Summary of RAM 30 30
Page 1
Ramset www.Ramsetinc.Com.
Page 2
Ramset www.Ramsetinc.Com.
Page 3: Ram 30-30
Ram 30-30 1 ramset www.Ramsetinc.Com important safety requirements & instructions ...................................................................................1 responsibilities of installers and technicians ....................................................................................2 ...
Page 4: Ram 30-30
2 ram 30-30 ramset www.Ramsetinc.Com installation •read and understand the instruction manual before attempting any installation. •do not exceed the equipment specifications. •insure a safe and proper installation. •install this equipment in accordance with the ul 325 specifications. •make sure to e...
Page 5: Ram 30-30
Ram 30-30 3 ramset www.Ramsetinc.Com prior to installation, the following must be observed: (per ul 325.56.8.4). A) install the gate operator only when: 1. The operator is appropriate for the construction of the gate and the usage class of the gate, 2. All openings of a horizontal slide gate are gua...
Page 6: Ram 30-30
4 ram 30-30 ramset www.Ramsetinc.Com vehicular horizontal slide-gate operator (or system) - a vehicular gate operator (or system) that controls a gate which slides in a horizontal direction that is intended for use for vehicular entrance or exit to a drive, parking lot, or the like. Vehicular swing-...
Page 7: Ram 30-30
Ram 30-30 5 ramset www.Ramsetinc.Com general specifications warning do not exceed the specifications. The warranty on your unit will be void if the installation exceeds the recommended specifications. Maximum gate size & weight: 20’ @ 3000 lbs gate traveling speed: approx 90° opening in 16 sec motor...
Page 8: Ram 30-30
6 ram 30-30 ramset www.Ramsetinc.Com concrete pad construction: dimensions given for the pad are based on soil bearing shear of 2000 p.S.F. These figures may have to be adjusted depending on local soil conditions. 1. Construct form for mounting pad according to dimensions shown in figure 1 and 2. 2....
Page 9: Ram 30-30
Ram 30-30 7 ramset www.Ramsetinc.Com note: 15 amp wires connected to independent breaker. Outlet leads gate travel is adjusted by loosening the lim- it cams and adjusting them until proper gate travel has been achieved. Standard installation for gates from 8’ to 16’ in length hookup electrical power...
Page 10: Ram 30-30
8 ram 30-30 ramset www.Ramsetinc.Com standard installation for gates from 16’ to 20’ in length space required for a standard gate in the open position 4’ gate opened 15 1/4” inside property outside property 4 ft. Length is the minimum space required between the open gate to the wall for this standar...
Page 11: Ram 30-30
Ram 30-30 9 ramset www.Ramsetinc.Com sensor installation reversing loops on the ground floor, prevents gate from closing when vehicle is in loop area. Exit loops on the ground floor, opens gate when vehicle crosses loop area. Photoelectric safety sensor (photo eye) prevents the gate from closing whe...
Page 12: Ram 30-30
10 ram 30-30 ramset www.Ramsetinc.Com three pushbuttons are located under the dip switches for operation of the gate (see figure 11). The opening, stop and closing buttons can be utilized to set limit switches and verify proper system operation when installing or servicing an operator. Opening: pres...
Page 13: Ram 30-30
Ram 30-30 11 ramset www.Ramsetinc.Com dip switch configuration dip switch "a" 1, 2 & 3; automatic timer to close gate ‘0’ is “off” ‘1’ is “on” switch 1 2 3 gate open duration: 1 1 1 60 seconds 1 1 0 45 seconds 1 0 1 30 seconds 1 0 0 15 seconds 0 1 1 10 seconds 0 1 0 05 seconds 0 0 1 00 seconds 0 0 0...
Page 14: Ram 30-30
12 ram 30-30 ramset www.Ramsetinc.Com dip switch "c" 4; “one pass” sw. Function: off normal operation - fully opens and closes on one pass mode - the gate will open until “the re- versing loop” is initially activated and then cleared, the gate will then close. If the “reversing loop” is then activat...
Page 15: Ram 30-30
Ram 30-30 13 ramset www.Ramsetinc.Com safety for ram 30 30 for ram 30 30 3/4 hp figure 14 terminal strip connection.
Page 16: Ram 30-30
14 ram 30-30 ramset www.Ramsetinc.Com terminal # 1 - common: low voltage common. Terminal # 2 - rev loop: stops the gate from closing. If the gate is open, it holds the gate open. If the gate is closing, it stops and reopens the gate. If the gate is closed, the gate will remain closed. The function ...
Page 17: Ram 30-30
Ram 30-30 15 ramset www.Ramsetinc.Com ramset “intelligate” control board introduction: ramset’s “intelligate” control board works with sliding, swinging and overhead vehicular gate operators. It is controlled by a program- mable microprocessor that reads and precisely executes all functions of the c...
Page 18: Ram 30-30
16 ram 30-30 ramset www.Ramsetinc.Com jp9 - input power: 1,2) 24 vac power. Connection from external transformer to power control board. Jp3 - 3 button: 1) open 2) stop 3) close 4) common used with a 3-button station to open, stop, and close the gate. The open and close are normally open connections...
Page 19: Ram 30-30
Ram 30-30 17 ramset www.Ramsetinc.Com figure 16 parts diagram 10 28 15 42 45 46 16 43 2 5 6 17 8 38 35 37 32 39 27 19 1 26 7 4 21 20 31 22 18 23 14 24 41 25 9 3 13 32 34 33 36 34 39 40 13 12 29 11 44.
Page 20: Ram 30-30
18 ram 30-30 ramset www.Ramsetinc.Com bill of materials for: ram 30-30 item part # part description 3/4 hp 1 hp 1 800-00-06 chassis 1 1 2 800-02-08 gear reducer - size 70, ratio 60:1 1 1 3 800-04-12 motor, standard - 120vac 3/4 hp 1 4 800-04-13 motor, standard - 220vac 1hp 1 5 800-06-00 sprocket - 1...
Page 21: Ram 30-30
Ram 30-30 19 ramset www.Ramsetinc.Com bill of materials for: ram 30-30 item part # part description 3/4 hp 1 hp 41 800-75-00 arm assembly 1 1 42 800-28-00 arm, metal tubing - 1” x 2” x 32” 1 1 43 800-28-01 arm, metal tubing - 1” x 2” x 42” 1 1 44 800-54-10 bracket, channel - 1 3/4” x 10” 1 1 45 800-...
Page 22: Ram 30-30
20 ram 30-30 ramset www.Ramsetinc.Com gate entrance safety precautions 1. Never let children operate or play with gate con- trols. Keep the controls away from children. 2. The entrance is for vehicles only. Pedestrians should use a separate entrance. 3. Always keep people, children and objects away ...
Page 23: Ram 30-30
Ram 30-30 21 ramset www.Ramsetinc.Com * ask your technician about all the features of our new ramset operator. * safety devices, such as reversing loops, phantom loops, photo eyes, or miller edges must be installed on your gate before the operator may be used. Ask your technician which safety device...
Page 24: Ram 30-30
22 ram 30-30 ramset www.Ramsetinc.Com troubleshooting table condition no lights are 'on'. Gate moves a couple of feet and then reverses. "exit" l.E.D. Is always 'on'. "rev loop" l.E.D. Always 'on'. "radio" l.E.D. Always 'on'. Gate doesn't open. Gate doesn't close. Gate doesn't close automatically. G...
Page 25: Ram 30-30
Ram 30-30 23 ramset www.Ramsetinc.Com lcd-keypad 1,024 codes 5,112 event log lcd display 7-day timer time zones latching stainless steel faceplate fire box allows the fire department to open the gate in the case of an emergency. Post mounts 1/4” angle iron flats. 3/16” square tubing legs. Used to mo...
Page 26
9116 de garmo ave. Sun valley, ca 91352 tel: (818) 504-2533 • fax: (818) 504-1141 www.Ramsetinc.Com.