Installation and operating instructions for ramsey universal wireless remote control for atv winches kit #’s 251203, 251204, 251205, & 251206 warnings 1. T he r amsey u niversal w ireless r emote for atv w inches is designed for use on self - recovery winches only . T he remote is not designed for a...
251203 superwinch atv 2000 & t 1500 parts list ........................................................1 before beginning installation ............................2 installing the kit ...............................................2-4 electrical schematic ........................................5 te...
1 251203 superwinch atv 2000 & t 1500 item no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 qty. 1 1 1 1 1 2 2 2 1 1 2 1 4 3 1 part no. 282058 251198 251234 251190 * 416227 418140 440125 251235 440274 description wireless receiver & transmitter kit dipole antenna kit solenoid kit replacement transmitter repl...
251203 superwinch atv 2000 & t 1500 before beginning installation 1. Disconnect power lead from winch to battery. 2. Disengage winch clutch. 3. Remove hood or cowling as necessary for easier access to installation area. 4. Locate & mark mounting locations for receiver, toggle switch, solenoid assemb...
Note: for clarification see wiring schematic on page 5. 1. Attach black with yellow stripe motor lead to lower right terminal stud “b” on solenoid. 2. Attach black motor lead to lower left terminal stud “c” on solenoid. 3. Attach connector with 2 yellow wires to the terminal directly above the black...
Note: for clarification see wiring schematic on page 5. 1. Connect red wire to center spade. 2. Connect green wire to the toggle switch terminal in the “out” position. 3. Connect the yellow wire to the toggle switch terminal in the “in” position. 1. Locate accessory wire from atv ignition. Note: acc...
E a c b 5 programing instructions: press and hold membrane below, press on/off button on transmitter for 3 seconds , press out button for 3 seconds or until winch activation . Www.Ramsey.Com (918)438-2760 fax(918)438-6688 tulsa . Oklahoma, usa . . Push black wire to ground yellow wire solenoid ass’y...
251203 superwinch atv 2000 & t 1500 6 1. Reconnect the positive power lead from solenoid to battery. 2. Pull approximately 20 ft of cable off the winch by hand. 3. Re-engage the winch clutch. 4. Test the remote transmitter. The transmitter has push buttons labeled accord- ing to their function. To t...
251204 warn a2000 / superwinch x1, x2, x1f, x2f, ex1 * sony cr2032 or duracell dl2032 item no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 qty. 1 1 1 1 1 2 2 4 2 1 1 2 1 1 part no. 282058 251198 251234 251190 * 416227 418140 440125 251235 440274 299724 description wireless receiver & transmitter kit dipole ant...
Installing the receiver 1. Insert plastic tie through mounting ears on receiver and secure receiver to location determined above. 2. Tighten plastic tie and clip excess. 3. Attach ground wire to atv frame. Caution: do not alter the length of the ground wire as this will affect performance of the rem...
9 note: for clarification see wiring schematic on page 11. 1. Attach black with yellow stripe motor lead to lower right terminal stud “b” on solenoid. 2. Attach black motor lead to lower left terminal stud “c” on solenoid. 3. Attach connector with 2 yellow wires to the terminal directly above the bl...
251204 warn a2000 / superwinch x1, x2, x1f, x2f, ex1 note: for clarification see wiring schematic on page 11. 1. Connect red wire to center spade. 2. Connect green wire to the toggle switch terminal in the “out” position. 3. Connect the yellow wire to the toggle switch terminal in the “in” position....
E a c b 11 programing instructions: press and hold membrane below, press on/off button on transmitter for 3 seconds , press out button for 3 seconds or until winch activation . Www.Ramsey.Com (918)438-2760 fax(918)438-6688 tulsa . Oklahoma, usa . . Push black wire to ground yellow wire solenoid ass’...
251204 warn a2000 / superwinch x1, x2, x1f, x2f, ex1 12 1. Reconnect the positive power lead from solenoid to battery. 2. Pull approximately 20 ft of cable off the winch by hand. 3. Re-engage the winch clutch. 4. Test the remote transmitter. The transmitter has push buttons labeled accord- ing to th...
251205 warn a2500 * sony cr2032 or duracell dl2032 item no. 1 2 3 4 5 6 7 8 9 qty. 1 1 1 1 1 1 1 1 1 part no. 282058 251198 251190 * 440125 440274 289189 description wireless receiver & transmitter kit dipole antenna kit replacement transmitter replacement battery wire splice cable ties warn adapter...
251205 warn a2500 before beginning installation 1. Disconnect power lead from solenoid to battery. 2. Disengage winch clutch. 3. Remove hood or cowling as necessary for easier access to installation area. 4. Locate & mark mounting locations for receiver, & antenna. Note: make sure locations are clos...
251205 warn a2500 15 installing the antenna note: for clarification see wiring schematic below. 1. Clean predetermined mounting surface with isopropyl alcohol and buff dry. (in atvs without hoods the best place to mount the antenna will be the underside of the atv cowling in the highest possible pos...
251205 warn a2500 16 1. Reconnect the positive power lead from solenoid to battery. 2. Pull approximately 20 ft of cable off the winch by hand. 3. Re-engage the winch clutch. 4. Test the remote transmitter. The trans- mitter has push buttons labeled accord- ing to their function. To operate the winc...
251206 superwinch x1, x2, x1f, x2f, ex1 (with hand held remote) 17 * sony cr2032 or duracell dl2032 item no. 1 2 3 4 5 6 7 8 9 qty. 1 1 1 1 1 1 1 1 1 part no. 282058 251198 251190 * 440125 440274 289190 description wireless receiver & transmitter kit dipole antenna kit replacement transmitter replac...
251206 superwinch x1, x2, x1f, xf2 ex1 (w/ hand held remote) before beginning installation 1. Disconnect power lead from solenoid to battery. 2. Disengage winch clutch. 3. Remove hood or cowling as necessary for easier access to installa- tion area. 4. Locate & mark mounting locations for receiver, ...
251206 superwinch x1, x2, x1f, xf2 ex1 (w/ hand held remote) 19 installing the antenna note: for clarification see wiring schematic below. 1. Clean predetermined mounting surface with isopropyl alcohol and buff dry. (in atvs without hoods the best place to mount the antenna will be the underside of ...
251206 superwinch x1, x2, x1f, x2f, ex1(with hand held remote) 20 1. Reconnect the positive power lead from solenoid to battery. 2. Pull approximately 20 ft of cable off the winch by hand. 3. Re-engage the winch clutch. 4. Test the remote transmitter. The transmitter has push buttons labeled accord-...
Trouble shooting guide correction turn transmitter on (see testing/operation) . Replace battery. In extremely cold tempera- tures, keep transmitter in a pocket of innermost layer of clothing when not in use. Make sure receiver ground wire has good connection to atv ground. Program receiver (refer to...
Ramsey winch company p.O. Box 581510 tulsa, oklahoma 74158-1510 usa phone: (918) 438-2760 fax: (918) 438-6888 http://www.Ramsey.Com om-914059-0106-j warranty information if the need should arise, warranty procedure is outlined on the back of your self-addressed, postage paid warranty card. Please re...
