Randell 11318 Specifications - Custom

1055 Mendell Davis Drive, Jackson, MS 39272

888-994-7636, fax 888-266-5244

Information contained in this document is known to be current and accurate at the time 

of printing/creation.  Unified Brands recommends referencing our product line websites, 

unifiedbrands.net, for the most updated product information and specifications.

Custom 

Remote Refrigerated Equipment Stand 

models 24000AR

Description:

Remote,  CFC  free,  refrigerated  cooking  equipment  stand  with 

reinforced stainless steel equipment shelf. Integral backsplash 

with  45˚  return.  Refrigerated  drawers  on  16  gauge  stainless 

steel tracks with 1 5/8" stainless steel bearings and removable 

plastic  pan.  6"  high  adjustable  legs.    R-134a  cooling  system 

with evaporator blower coil and expansion valve supplied and 

installed.  

Shown with optional finished end.

Standard Features:

• Available under one piece top with other modular equipment up 

   to 16' in length

• 6" high legs—adjustable and movable

• 10 3/8" wide x 1 1/4" thick laminated maple work board

• Self-closing drawers with removable plastic pan

• Evaporator blower coil with expansion valve, solenoid valve, 

   thermostat, and refrigeration lines provided and installed, 

   R-134a refrigerant, CFC free 

• If unit is fitted with vent, then backsplash will be 3" thick to

   meet NFPA 96

• 45˚ integral stainless backsplash is standard. 90˚ stainless 

   steel backsplash is optional.

• Equipment Rails are optional

Specifications:

EQUIPMENT  SHELF:  Equipment  shelf  to  be  one  piece  of  die-

formed stainless steel with 2" nosing and marine edge. Shelf is 

reinforced with welded channel brace assembly. 

UNIT BODY: Body ends to be die-formed stainless steel, finished 

and polished on the inside, with corrosion resistant exterior. Ends 

at top fitted with recessed heavy duty steel bars for splining units 

together,  producing  a  hairline  seam.  Backsplash  to  be  coved 

cornered, with 45˚ return at top and overall height of 6 3/4". (If 

fitted with vent system, standard backsplash to be omitted and 

unit fitted with 3" thick backsplash to meet NFPA 96). 10 3/8" 

wide x 1 1/4" thick laminated maple cutting board provided with 

removable  supports.  Base  interior  to  be  ABS  thermoplastic  at 

ends only. Stainless steel interior liner to be coved cornered to 

form  bottom,  back  and  top.  Unit  insulated  with  CFC  free,  high 

density polyurethane expanding foam. Units totally prewired to 

junction box.  Legs to be 6" high stainless steel, with adjustable 

bullet foot. Legs mounted to full length channel frame assembly 

which is integrally welded to bottom of assembly. Legs can be 

moved left to right to avoid floor obstacles during installation.

DRAWERS:  Remote  refrigerated  drawers  are  located  below 

equipment  shelf.  Drawer  liners  are  plastic,  removable  without 

tools, with drawer tracks of 16 gauge stainless steel with 1 5/8" 

stainless steel bearings, self-closing. Drawer opening frame to be 

ABS  and  contain  magnetic  strip  for  positive  sealing  of  gaskets. 

Drawer  fronts  to  be  22  gauge  stainless  steel  with  16  gauge 

stainless steel handles, magnetic gaskets, and plastic pan. 

REFRIGERATION: Interior fitted with Randell R-134a evaporator 

blower  coil  for  cooling  base.  Expansion  valve,  solenoid  valve, 

thermostat,  and  refrigeration  lines  provided  and  installed  for 

connection  at  unit  rear.    Condensing  unit  and  controls  not 

provided. Units totally prewired to junction box.

Randell Custom, Page 7

Revised 09/04

model 

24348AR 

24366AR 

24378AR 

24384AR 

24396AR 

243102AR   243114AR