Rane AC 23B Operator's Manual

Other manuals for AC 23B: Datasheet, Operator's Manual, Datasheet, Datasheet

Summary of AC 23B

  • Page 1

    Manual-1 ac 23b active crossover operators manual quick start labels above the controls refer to the unit being operated in the 2- or 3-way stereo mode. Labels below the controls refer to the unit being operated in the 4- or 5-way mono mode. Set the stereo/mono switch appropriately. The fact that th...

  • Page 2

    Manual-2 front panel: stereo 2-way configuration observe the labels above the controls for stereo operation. * not used in 2-channel 2-way mode 햲 channel 1 master level control: sets the overall level of channel 1 without altering the relative settings of the low and high frequency outputs. Unity ga...

  • Page 3

    Manual-3 mono 5w (change internal switch for mono 4w) hi mid out-5w low out high out omit-4w omit mono n108 made in u.S.A. Rane corp. Low-3w / omit-2w mid-3w / low-2w high out 3w 2w channel 2 stereo channel 1 stereo mono mono 4w / 5w in omit mono sub out mid out low-3w / omit-2w mid-3w / low-2w 3w 2...

  • Page 4

    Manual-4 front panel: stereo 3-way configuration observe the labels screened above the controls for stereo operation. 햲 channel 1 master level control: sets the overall level of channel 1 without altering the relative settings of the low/mid/high frequency outputs. Unity gain for all level controls ...

  • Page 5

    Manual-5 mono 5w (change internal switch for mono 4w) hi mid out-5w low out high out omit-4w omit mono n108 made in u.S.A. Rane corp. Low-3w / omit-2w mid-3w / low-2w high out 3w 2w channel 2 stereo channel 1 stereo mono mono 4w / 5w in omit mono sub out mid out low-3w / omit-2w mid-3w / low-2w 3w 2...

  • Page 6

    Manual-6 front panel: mono 4-way and 5-way configuration observe the labels screened below the controls for mono operation. 햲 master level control: sets the overall level of the entire unit in mono mode, without changing relative settings of the individual sub/low/mid/high outputs. Unity gain for al...

  • Page 7

    Manual-7 헁 hlgh-mid mute switch: removes all signal from the high-mid output when pressed to the in position. This control is disabled in 4-way mode. 헂 hlgh-mid delay control: this control adds from 0 to 2 ms of time delay to the high-mid output only. This control is disabled in 4-way mode. 헃 hlgh-m...

  • Page 8: * *

    Manual-8 rear panel: mono 4-way and mono 5-way installation mono 5w (change internal switch for mono 4w) hi mid out-5w low out high out omit-4w omit mono n108 made in u.S.A. Rane corp. Low-3w / omit-2w mid-3w / low-2w high out 3w 2w channel 2 stereo channel 1 stereo mono mono 4w / 5w in omit mono su...

  • Page 9

    Manual-9 rear panel: alternate mono 4-way installation note: the switching in the ac 23b will result in a mono 4-way configuration with the crossover ranges sub, low, mid & high from left to right across the bottom front panel. By connecting a patch cable from the channel 1 high out to the channel 2...

  • Page 10

    Manual-10 operating instructions selecting crossover frequencies most speaker manufacturers supply low and/or high frequency cut-off points for each driver, especially if these are supplied in a system. These cut-off frequencies are based on each driver’s performance at and beyond this point, with a...

  • Page 11

    Manual-11 fig. 1 in-phase axis response without time delay fig. 2 corrected in-phase axis response with electronic time delay on low frequency driver time delay adjustment using realtime analyzer & pink noise this method outlines the use of a realtime analyzer, pink noise generator and flat response...

  • Page 12

    Manual-12 less amount of correction capability. If the drivers are built into a single cabinet and/or it is impossible to change relative positions, then you will have to obtain additional external delay to achieve proper phase alignment. The rane ad 22b would be suitable. Iv. If turning the mid del...

  • Page 13

    Manual-13 step by step procedure a 3-way mode consisting of high, mid and low drivers is used here as an example. For other configurations, use the same procedure starting with the highest crossover point and repeating steps 2 through 5 for each lower crossover point. 1. Set the tone generator to th...

  • Page 14

    Manual-14 voice coil displacement (inches) (hz) .75" 1.5" 3" 6" 9" 12" 15" 18" 21" 24" 70 1 1.5 2 2.5 3.5 5 6 7 8 max 80 1 1.5 2 2.5 3.5 5 6 7 8 max 100 1 1.5 2 2.5 3.5 5 6 7 8 max 150 1 1.5 2 2.5 3.5 5 6 7 max 200 1 1.5 2 2.5 3.5 5 6 7 max 250 1 1.5 2 2.5 3.5 5 7 8 max 300 1 1.5 2 2.5 3.5 5.5 7 max...

  • Page 15

    Manual-15 setting the output level controls choosing the crossover frequencies was the easy part. Now it gets real fun. The idea is to set the output level controls on the crossover so that the entire speaker system has a uniform, flat response. Unfortunately, the room in which the speakers are plac...

  • Page 16

    Manual-16 constant directivity horn eq mod constant directivity (or cd) horns need additional equalization to help cover the same area a long throw horn can cover. Additional circuitry has been added to the ac 23b for additional equalization of the high frequency outputs for the cd horns. This modif...