Rane MPE 28 Operating And Service Manual

OPERATING / SERVICE MANUAL

MPE 28

MIDI PROGRAMMABLE EQUALIZER

QUICK START

Reading owners manuals is like eating vegetables—a nuisance which is necessary, at least according to your mother. It

ensures longevity and proper operation of your systems but chocolate soda is more fun. In the event you want to find a

short-cut we provide this section to help you avoid the spinach. At least read this and save the rest for later. And remem-

ber—clean your plate, people are starving somewhere.

Upon initial power-up, you should see the words, “Rane MPE 28...rX.X” (the current revision level) scroll by in

the SYSTEM display window. Then the SYSTEM display indicates the last memory location used before the power was

turned off, and the green MEMORY indicator lights. The MPE 28 is now ready to use.

(The MPE 28 has two levels of security lockout. If you think your unit may be in either of these lockout modes, please

consult the enclosed MPE Users Guide for further instructions.)

Two terms need to be learned early on. The first is Stored Memory. Stored Memory is any of the 128 locations provided

for curves. The second is Working Memory. Working Memory is a scratch-pad location used for changing curves before

you put them into Stored Memory. Working Memory is also what you hear.

The first few Stored Memory locations (programs 1 to 21) were preset at the factory. A table of these is in the MPE

Users GuideAppendix. In the beginning these give you instant curves for experimenting. If you want a different curve,

press the UP/DOWN buttons to scroll, or directly enter a Stored Memory number via buttons 0 through 9 (observe the red

SYSTEM display). Please note that all Stored Memory numbers must be at least two digits; e.g., Stored Memory number4

is entered as 04, etc. For direct access to Stored Memory locations above99, push the 100 button, then the next two digits.

For example, to recall Stored Memory125, press 100, 2 and 5, and you will have arrived! Once the last digit is entered,

the Stored Memory is instantly called up (what you see is what you hear).

Changing the overall level or equalizer curve requires the use of the EQ Edit mode. Push the EQ button (repeated

operation cycles between the first half of the frequencies, the second half and neither) to select the frequencies you wish to

modify. Now press LEVEL or the frequency button desired (the yellow LED lights). Next scroll the UP/DOWN buttons

until the desired level shows on the green EQUALIZER display. When finished editing, push the STORE button once,

enter a new Stored Memory number if needed, then push STORE again to place the new curve into the Stored Memory

shown on the red SYSTEM display. Presto facto, it’s Miller time. See the enclosed MPE Users Guide for futher details.

The MPE 28 presets can be recalled either by front panel or externally through MIDI. If you have a PC with a MIDI

interface, Rane can supply you with a DOS graphic editor program just for asking (no charge). If you have a Mac, see the

Galaxy Universal Librarian from Opcode Systems. Other software companies may have other librarians that will work. If

you would like to change presets with external switches, check out the Rane RPS 4 Remote Program Selector.

CAUTION: NEVER CONNECT ANYTHING EXCEPT RANE MODELS RS 1, RAP 10 OR FRS 8 AC POWER SUPPLIES

TO THE RED THING THAT LOOKS LIKE A TELEPHONE JACK ON THE REAR OF THE MPE 28. This is a low-voltage

AC power input and requires some special attention if you use anything except an approved Rane power supply.

SYSTEM CONNECTION

When connecting the MPE 28 to other components in

your system for the first time, leave the power supply for last.

This will give you a chance to make mistakes and correct

them before any damage is done to fragile components in the

system.

INPUT. The input on the MPE 28 is balanced/unbalanced.

This means that standard ¼" connectors on the ends of any

good quality cable will work well between your signal

sources, signal processing and amplification. If balanced ¼"

input is your choice, use a Tip-Ring-Sleeve connector; wire

the tip as hot (+), the ring as return (–), and the sleeve as

signal ground. The MPE 28 also gives you the opportunity to

use a 3-pin (XLR) input connector. Balanced operation

through this Input requires pin 2 be used as hot (+), pin 3 as

return (–), and pin 1 as signal ground. Unbalanced sources

require that pin 1 be connected to pin 3 on the Input connec-

tor only. Therefore, pin 2 is hot, pins 1 and 3 are signal

ground.

OUTPUT. The MPE 28 offers a similar choice of output

connector and the wiring is the same as far as polarity of pins

is concerned. When hooking up an unbalanced Output using

the 3-pin, disregard the italics in the preceding paragraph.

DO NOT connect pin 3 to pin 1. Leave it open, please. Thank

you.

You should be aware, also, that just because we indicate

that a sleeve on a ¼" or pin one on a 3-pin is used for ground-

ing, it is not always wise to use it. Rane Note 110 (included

with your unit) goes into the reasons and logic behind all of

this madness. Please have a look at it to try to attain the best

performance possible from your MPE 28.