- DL manuals
- Rane
- Mixer
- TTM 56S
- Manual
Rane TTM 56S Manual
Summary of TTM 56S
Page 1
Ttm 56s performance mixer 17812 contents important safety instructions 2 quick start 3 rear panel hook-up 4 mixer controls 5 maintaining magnetic faders 8 block diagram 10 specifications 12 dimensions 13 serato scratch live 14 sound system interconnection 17 warranty 25 declaration of conformity 27.
Page 2
2 risk of electric shock do not open caution to reduce the risk of electrical shock, do not open the unit. No user serviceable parts inside. Refer servicing to qualified service personnel. The symbols shown below are internationally accepted symbols that warn of potential hazards with electrical pro...
Page 3
3 ttm 56s performance mixer quick start congratulations! You are the proud owner of an exceptional performance instrument. Experienced turntablists will find the ttm 56s comfortable and familiar. The ttm 56s has many unique features which are mastered quicker if you read the manual. Right! We know y...
Page 4
4 rear panel hook-up power the ttm 56s features an internal universal switching power supply that operates on any ac mains 100 to 240 vac, 50 or 60 hz (most places in the world). All that is required when traveling is the appropriate iec line cord available in each country. The universal supply is a...
Page 5
5 mixer controls mic section mic level sets the gain of the mic input. The range is off to +44 db. There is no engage switch, so set the mic level to zero (0) when you aren't using it. The mic input minimum gain is 26 db, so a line- level mic source (such as a wireless receiver) must be padded. The ...
Page 6
6 channel swap switch allows the left-hand or right- hand fader to alternately control pgm 1 or pgm 2. (don't confuse with the reverse switches, see below.) contour controls allow smooth, continuous adjustment of contour. The range of control is from slow blend to fast cut, adjustable independently ...
Page 7
7 +12 -12 +12 -12 ol 10 0 r l +6 off 10 0 6 4 2 8 6 4 2 8 10 0 6 4 2 8 ol +8 +4 +2 0 –4 –2 –8 –16 –24 performance mixer 10 0 6 4 2 8 +6 off +6 off out in out r l out in out +6 off +6 off +6 off 10 0 2 4 8 6 10 0 2 4 8 6 10 0 2 4 8 6 mic low mic high aux in output levels main source pgm 1 pgm 2 2 1 a...
Page 8
8 maintaining magnetic faders there are no electrical contacts to clean! The faders in the ttm 56s are designed with materials highly resistant to corrosion and most chemicals. While the faders will handle millions of operations, they may become dirty over time. Bad things may be spilled or sprayed ...
Page 9
9 fader removal for more effective cleaning and lubrication, follow the directions outlined below: 1. Required tools: #1 philips screwdriver and a pair of clean hands. 2. Disconnect the power. 3. Remove the fader caps by pulling them away from the lexan faceplate. 4. Remove the four 4-40 screws atta...
Page 10
10 ttm 56s performance mixer block diagram 15 hz hp riaa phono line gain off +44 db low high eq -12 +12 ol eq +6 ol send return pgm 4 left 3 source 4 pgm 3 left low mid high low mid high eq off off +6 ol ch 1 fader channel swap ch 2 fader +5 +5 +12 -12 +12 -12 left master out aux out +10 +7 -2 -4 -7...
Page 11
11 ttm 56s performance mixer 15 hz hp riaa phono line gain off +44 db low high eq -12 +12 ol eq +6 ol send return pgm 4 left 3 source 4 pgm 3 left low mid high low mid high eq off off +6 ol ch 1 fader channel swap ch 2 fader +5 +5 +12 -12 +12 -12 left master out aux out +10 +7 -2 -4 -7 -20 -10 +4 +2...
Page 12
12 ©rane corporation 10802 47th ave. W., mukilteo wa 98275-5000 usa tel 425-355-6000 fax 425-347-7757 web dj.Rane.Com parameter specification conditions & comments program inputs: phono: switchable line / phono unbalanced rca jacks ..........Response riaa ±1 db ..........Gain 40 db 1 khz ..........I...
Page 13
13 ttm 56s performance mixer dimensions rear view front view aux phono grounds power pgm 1 pgm 2 4 3 2 1 4 4 3 3 2 2 1 1 4 3 2 1 100-240v 50/60 hz 20 watts acn 001 345 482 made in u.S.A. Rane corp. Out in out in mic balanced master outputs r l r l r l r l r l r l line phono ttm 56s commercial audio ...
Page 14
Serato scratch live • data sheet 1 file preparation build waveform overviews, check for file corruption and use scratch live’s optional auto-gain and bpm calculation with the analyze files button. Use the offline player to prepare crates, audition tracks, and set cue and loop points, without needing...
Page 15
Serato scratch live • data sheet 2 track overview display shows an overview of the track waveform, which is useful for finding transitions in a track and for jumping quickly to any part of the song. Colored waveforms are by frequency for visual identification of instruments and vocals. Scratch live ...
Page 16
Serato scratch live • data sheet 3 serato control vinyl & cd serato control vinyl and control cds are included with rane hardware. These each contain the serato noisemap™ control tone, a unique control signal which allows scratch live to track the motion of the record, simulating the same movement w...
Page 17: Ranenote
Interconnection-1 introduction this note, originally written in 1985, continues to be one of our most useful references. It’s popularity stems from the continual and perpetual difficulty of hooking up audio equipment without suffering through all sorts of bizarre noises, hums, buzzes, whistles, etc....
Page 18
Interconnection-2 ground loops almost all cases of noise can be traced directly to ground loops, grounding or lack thereof. It is important to understand the mechanism that causes grounding noise in order to effectively eliminate it. Each compo- nent of a sound system produces its own ground in- ter...
Page 19
Interconnection-3 the absolute best right way to do it the method specified by aes48 is to use balanced lines and tie the cable shield to the metal chassis (right where it enters the chassis) at both ends of the cable. A balanced line requires three separate conduc- tors, two of which are signal (+ ...
Page 20
Interconnection-4 another way to create the necessary isolation is to use a direct box. Originally named for its use to convert the high impedance, high level output of an electric guitar to the low impedance, low level input of a re- cording console, it allowed the player to plug “directly” into th...
Page 21
Interconnection-5 buzzing, there is an incompatibility somewhere in the system’s grounding configuration. In addition to these special cable assemblies that may help, here are some more things to try: 1. Try combinations of lifting grounds on units sup- plied with lift switches (or links). It is wis...
Page 22: To Input
Interconnection-6 figure 4. Interconnect chart for locating correct cable assemblies on the following pages. Note: (a) this configuration uses an “off-the-shelf” cable. Note: (b) this configuration causes a 6 db signal loss. Compensate by “turning the system up” 6 db. To input male balanced xlr ¼" b...
Page 23: Input
Interconnection-7 10 9 s=shield r=nc t=red s=shield r=nc t=red 8 7 s=shield r=black t=red s=shield r=black t=red male 6 5 3=black black 4 3 3=nc 2=red 1=shield shield shield 2 female 1 3=black 2=red 1=shield male b b b b s=nc r=black t=red s=shield r=black t=red 11 cross-coupled output only: connect...
Page 24: Input
Interconnection-8 doc 102907 ©rane corporation 10802 47th ave. W., mukilteo wa 98275-5000 usa tel 425-355-6000 fax 425-347-7757 web www.Rane.Com 22 21 male (any unbalanced connector) (any unbalanced connector) (check: no standard polarity on euroblocks) (check: no standard polarity on euroblocks) 20...
Page 25
25 ttm 56s performance mixer factory authorized service your unit may be serviced by the rane factory or any authorized rane service center. To find a service center near you, please call the rane factory, or check the rane website. Please do not return your unit to rane without prior authorization....
Page 26
26 ttm 56s performance mixer warranty procedure - valid in usa only notice! You must complete and return the warranty card or register your product online to extend the warranty from 2 years to 3 years! To validate your extended warranty: use the postcard that came in the box with your unit, or go t...
Page 27
· · (signature) june 30, 2010 (date) mukilteo wa, usa (place) compliance engineer (position) declaration of conformity application of council directive(s): 2001/95/ec 2002/96/ec 2004/108/ec 2006/95/ec 2011/65/eu manufacturer: rane corporation 10802 47th avenue west mukilteo wa 98275-5000 usa this eq...
Page 28: Ttm 56S
Ttm 56s performance mixer ©rane corporation 10802 47th ave. W., mukilteo wa 98275-5000 usa tel 425-355-6000 fax 425-347-7757 web dj.Rane.Com aux phono grounds power pgm 1 pgm 2 4 3 2 1 4 4 3 3 2 2 1 1 4 3 2 1 100-240v 50/60 hz 20 watts acn 001 345 482 made in u.S.A. Rane corp. Out in out in mic bala...