- DL manuals
- Ransomes
- Lawn Mower
- 933308G
- Operator's manual
Ransomes 933308G Operator's manual
Summary of 933308G
Page 1
Opera t or’s manual man 4166158-gb rev .A 05-201 1 original language instructions models: 933308g 36 hydro z-control mid-fs541v kaw side discharge self propelled walk behind mower 933309g 36 hydro z-control mid-fs541v kaw rear discharge self propelled walk behind mower parts manual 4166157.
Page 2: Advertencia
California proposition 65 warning diesel engine exhaust and some of its constituents are known to the state of california to cause cancer, birth defects and other reproductive harm. Californie proposition 65 avertisse- ment les échappements des moteurs diesel et certains de leurs composés sont recon...
Page 3: Hydro
3 ec hydro midsize 05-2011 important message thank you for purchasing this ransomes product. You have purchased a world class mowing product, one of the best designed and built anywhere. This machine comes with an operation and safety manual and a separate setup, parts and maintenance manual. The us...
Page 4: Hydro
4 ec hydro midsize model number: this number appears on sales literature, technical manuals and price lists. Serial number: this number appears only on your mower. It contains the model number followed consecutively by the serial number. Use this number when ordering parts or seeking warranty inform...
Page 5: Hydro
5 ec hydro midsize labels operation & safety manual - read and understand operation & safety manual. - replace if lost or damaged. Thrown objects hazard - keep area clear of people and pets. - remove objects blade may strike and throw. - stop blades to cross gravel ares. - do not operate without chu...
Page 6: Hydro
6 ec hydro midsize labels tire infl ation - infl ate tires to 0.97 kg/cm 2 [14lb/in 2 ] high pressure fluid - leaks can penetrate skin. - seek immediate attention for oil penetration injury. - see operation & safety manual for procedures to fi nd leaks and to service hydraulic system. Hydraulic flui...
Page 7: Hydro
7 ec hydro midsize labels operation & safety manual - read and under- stand operation & safety manual. - replace if lost or damaged. Thrown objects - keep bystanders a safe distance away. - remove objects on ground blade may strike - stop blades before crossing gravel. Slope hazard - do not use on w...
Page 8: Hydro
8 ec hydro midsize j) never operate the equipment in wet grass. Always be sure of your footing. Keep a fi rm hold on the handle and walk, never run. Before using machine for the fi rst time, check engine and hydraulic fl uid levels and lubricate all points. Training a) read the operator’s manual car...
Page 9: Hydro
9 ec hydro midsize general instructions q) stop the engine, wait for the blades to come to a complete stop, and disconnect the spark plug wire: before clearing blockages or unclogging chute. Before checking, cleaning or working on the mower. after striking a foreign object. Inspect the mower for d...
Page 10: Hydro
10 ec hydro midsize general instructions leaving the driving position park the machine on level ground. Before leaving the driving position, stop the engine, make sure all moving parts are stationary and that the traction control levers are in the neutral position. Apply parking brake. Maintenance a...
Page 11: Hydro
11 ec hydro midsize controls control levers (a) the control levers must be in the neutral position and the blades must be off for the engine to start. The control levers must be held in for pto operation. If the pto switch is on, and the control levers are released, the engine will kill. The neutral...
Page 12: Hydro
12 ec hydro midsize controls tracking adjustment turnbuckle the tracking adjustment turnbuckle provides tracking control to correct for any hydraulic circuit or linkage differences from one side to the other. To correct tracking: 1. Loosen wing nut x. 2. Rotate the tracking adjustment turnbuckle y t...
Page 13: Hydro
13 ec hydro midsize machine operation before starting the engine: • disengage cutterdeck drive. • traction levers are positively locked in neutral. • parking brake is on and speed selector is in neutral. 1. Check the engine oil level and add if necessary. Open the fuel valve under the fuel tank. Set...
Page 14: Hydro
14 ec hydro midsize machine operation cutting with the machine 1. Make sure the discharge chute is in position or a grass collector is correctly fi tted before starting to cut. 2. Depress the operator present controls. 3. Turn blades on with the pto switch. 4. Do not start blades at full throttle. U...
Page 15: Hydro
15 ec hydro midsize pushing the machine with the engine stopped: open dump valve v on each pump by turning counter clockwise two revolutions. Move the machine and close dump valve v by turning clockwise until valve is fi rmly seated. Machine operation.
Page 16: Hydro
16 ec hydro midsize make all adjustments with the engine shut off, spark plug wire disconnected and mower drive disengaged. Fixed cutterdeck height of cut the cutting height is determined by the position of the blades in relation to the wheels. Variation to this height may be made at three points. (...
Page 17: Hydro
17 ec hydro midsize height of cut setting cutterdeck height cutterdeck position . 1. Support rear of power unit. 2. Place blocks under both outside edges of cutter- deck at b. See block chart below. 3. Remove (2) upper deck mounting bolts c. 4. Loosen (2) lower deck mounting bolts d several turns. L...
Page 18: Hydro
18 ec hydro midsize height of cut speed control bar the speed control bar f is held by friction pads. If the setting will not hold, tighten knob e to increase friction on speed control bar f. Parking brake - apply parking brakes and open the bypass valves on the hydraulic pumps. Try to push the mach...
Page 19: Hydro
19 ec hydro midsize belt replacement cutterdeck belt 1. Remove pto belt. 2. Rotate idler arm using a 3/8" (9mm) ratchet or breaker bar and remove belt. 3. Replace in the reverse order. Pump-drive belt 1. Remove pto belt from the engine clutch. 2. Disconnect the clutch wire harness. 3. Unbolt clutch ...
Page 20: Hydro
20 ec hydro midsize adjustments tracking width adjustment the tracking width originally set from the factory can be increased an additional 83 mm overall by performing the following steps. 1. Loosen wheel lug nuts on both drive tires. 2. Raise rear of unit so that drive tires are off the ground. Sup...
Page 21: Hydro
21 ec hydro midsize traction drive hydrostat adjustments: the following adjustments must be done in order. Adjustments step 1 - set neutral neutral is set at the factory. If it should require adjustment, raise the wheels off the ground by setting the machine on jackstands or blocks. Disconnect the c...
Page 22: Hydro
22 ec hydro midsize adjustments control levers the control levers are controlled by spring tension, and require no adjustment. Handle bar height adjustment to adjust handle bar height: remove swivel b at each pump control arm and the parking brake rod. Remove bolts g and loosen bolts e on each side ...
Page 23: Hydro
23 ec hydro midsize specifications power units controls: throttle, choke, pto switch, speed selector knob, key switch, operator present,control levers (1 per wheel), parking brake. Ground speed: 0-5.2 mph forward 0-1.7 mph reverse drive tires: 16 x 7.50 turf saver brakes: hydrostat provides dynamic ...
Page 24: Hydro
24 ec hydro midsize specifications.
Page 25: Hydro
25 ec hydro midsize specifications.
Page 26: Hydro
26 ec hydro midsize ec declaration of conformity the undersigned manufacturer: ransomes one bob-cat lane johnson creek, wi 53038 authorized representative: earlsmere limited unit 18 valley road station road industrial estate wombwell, barnsley, south yorkshire, s73 obs uk notifi ed body: av technolo...
Page 28
Ransomes jacobsen limited ransomes way ipswich, england, ip3 9tt.