Summary of KG888
Page 1
User manual.
Page 2
1 features: 1. Code hopping and code learning. 2. Remote starting. 3. Remote (silent) arming/disarming. 4. Starter disable (500ma negative output when armed) 5. Auto re-arm. 6. Driving lock mode. 7. Car (silent) searching. 8. Audible intrusion zone identification. 9. Defective zone alert and by-pass...
Page 3
2 3. If door Ε trunk Ε hood is opened or acc (ignition switch) is turned on, the system will sound for 60 seconds. Intrusion identification: if the vehicle is tampered with or intruded, when disarming the alarm, the siren will chirp different sounds to identify which zone has been tempered. 1. Secon...
Page 4
3 last door arming: 1. Whenever the ignition is turned from on to off and all doors are closed, after 20 seconds the siren will echo 2 chirps (lamps flash twice) to remind the driver and 10 seconds later, the system will lock the doors and enter armed mode automatically. 2. Set / release “last door ...
Page 5
4 1. One chirp turbo timer is on 2. Two chirps turbo timer is off (factory default) remote engine start warm-up time: this system has two options for start warm-up time - 6 or 18 minutes, which is programmed by remote. Turn on the ignition switch, press button ҇ʾ҉ ʳ at the same time for over 2 secon...
Page 6
5 > button ignition off ignition on engine start in arm mode press button ҇ arm/ car search lock lock press button ҈ disarm unlock disarm/ unlock press button ҉ silent arm/ silent car search press button Ζ ʳ ʳ ˹̂̅ʳ˄ʳ̆˸˶̂́˷ remote start on/off kill engine press button ҇ over 2 sec. Remote panic anti-...
Page 7
6 ϪϪϪʳ illustration of 2-way controller ʳ ϪϪϪʳ learning transmitter codes: step 1 : in disarmed mode, turn the ignition switch on/off five times ( each time must be finished within 1 second, or alarm system will skip it) and keep the ignition switch to "on" position, siren will echo 4 chirps. Step 2...
Page 12
Table of contents introduction………………………………………………………………………………………… 1 6-pin white plug red wire (12 volts positive input)…………………………………………………………….... 2 black wire (ground input)……………………………..………………………………………… 2 yellow/green wire (start output)…...……..……………..……………………………………. 2 blue/white wire (ignition 1)……...
Page 13
1 kg888 installation handbook introduction this installation handbook is designed for the professional installer. This book assumes the installer has a comprehensive understanding of how automotive electrical systems operate and the proper way to test and connect wiring for proper operation. Install...
Page 14
2 installation red wire- 12gauge 5 th pin of 6-pin white plug 12 volts positive input connect red wire to positive terminal of vehicle battery, do not connect main power at fuse box or ignition switch. Make certain fuses are removed from holders to prevent any possible shorts while routing wire. Bla...
Page 15
3 note: in some vehicles, additional secondary ignition may be required to operate separate ac/heater circuitry and anti-theft systems. Red/green wire- 14gauge 3 rd pin of 6-pin white plug ignition 2 this wire is for main ignition operation. Vehicle’s main ignition wires operates the coil, fuel pump...
Page 16
4 diagram 3: gm 1988-1994 grand prix, cutlass supreme, buick regal, and chevrolet lumina diagram 4: 1993 & later ford/lincoln/mercury (including trucks) diagram 5: toyota/lexus dual ignition diagram 6: dodge/chrysler/plymouth/eagle lh body style (intrepid\lhsew york\concorde\vision) ignition wirin...
Page 17
5 to overcome the passkey system when remote starting, a resistor of identical value must be installed to deactivate the anti-theft system. Use relay diagram below. Locate the two pass key wires in the steering column. These wires may have insulating jacket around them. These wires may also be locat...
Page 18
6 ignition wiring: special instructions general motors passlock system this system is currently found in general motors 1996 chevrolet cavalier, pontiac sunfire and pontiac grand am. Below is the diagram showing how to bypass this system. Gray wire - 20gauge 9 th pin of 9-pin white plug negative win...
Page 19
7 white wire - 18gauge 7 th pin of 9-pin white plug flashing parking light connect this wire to the vehicle's positive 12 volts parking/turn signal/hazard lights. American and japanese vehicles , the parking lights operate on a single fused circuit. Connect the white wire directly to the back of any...
Page 20
8 red/white wire - 20gauge 4 th pin of 9-pin white plug optional trunk release output unless the vehicle's trunk release switch negatively triggers a solenoid that draws no more than 250ma, an external relay must be used. The following diagram shows the typical connection: violet wire - 20gauge 3 rd...
Page 21
9 optional auxiliary plug-in dual zone sensor 4-pin white plug plug the auxiliary dual stage sensor's connector into the alarm's 4-pin white plug; this port supplies 12 volts (red wire), ground (black wire), 1 st stage trigger (green wire), and 2 nd stage trigger (blue wire). Plug-in red led status ...
Page 22
10 power door lock interface 3 -pin red plug for vehicle having negative pulse door lock switches, connect the green wire to the vehicle's lock switch wire and the blue wire to the vehicle's unlock switch wire directly. Show the connection below: ϥ ʳ the vehicle has original built-in central power l...
Page 23
11 ϥ ʳ the vehicle has built-in power lock and using compressor to control the switch. For example: benz, audi (note: active time 5 seconds). ϥ ʳ the vehicle has built-in power lock that utilizes a single wire between the door lock switch and a control unit that is used by both lock and unlock the d...
Page 24
User manual.