Assembly instructions 4-wheel wagon reel model gh168-wg professional garden hose reels.
Page 2 10 year warranty coverage rapid-reel ® and reel quick, inc. (collectively here after referred to as the "warrantor"), guarantees this hose reel, components and parts, unless otherwise specified, to be free from defect, malfunction or failure in material, or workmanship, under normal use and s...
U a b aa r p bb y c o q g h x j f e d page 3 reel specifications 5/8” capacity ............225 feet 3/4” capacity ............175 feet max. Temperature ....140° f max. Pressure ..........100 psi patent pending release button s v k w z t l i m n reel capacities may vary depending on hose brand and st...
Page 4 reel & frame assembly 1 2 3 click click actual size of # 3 screwdriver. 3x press back bushing (e) into back flange (a). Press firmly until all tabs “click” into place. Press front bushing (f) into front flange (b). Press firmly until all tabs “click” into place. F a e a b using a #3 phillips ...
5 6 8 7 page 5 2x 2x 2x 2x 2x 3x 4 3x 3x actual size of # 3 screwdriver. I h k q o t l r t l using a #3 phillips screwdriver, attach the handle (h) using three nylon insert nuts (i) and three 5/8” screws (k). Tighten firmly as the nylon insert nuts will require extra force. Slide three frame tubes (...
11 12 page 6 2x 2x 2x 2x 9 2x 10 2x 13 slide the two tire spindles (s) onto the elbow assemblies. S be sure to take note of proper positioning of spindle notches. Slide two frame tubes (o) onto the elbow and into the tire spindles and align holes. O attach the elbow, spindle and tube together using ...
15 16 10x 17 18 page 7 14 4x p slide the t-handle (p) into the frame tube. T m using the hex key (m), firmly tighten all ten tube screws. Secure the t-handle to the frame tube using a 1-3/4” screw (t) and a serrated nut (l). L note: be sure to align the stub on the axle with the notch in the frame w...
21 22 page 8 19 20 4x 4x v w g firmly push the adjustable brake (g) onto the axle. Make sure it is fully seated into the front bushing. Push firmly do not tighten the brake at this time! Slide flange assembly onto the reel axle. Place the four tire washers (v) onto the tire axles. Insert the four co...
25 26 page 9 24 23 27 c d lock the swivel onto the reel by aligning it’s tabs with the slots in the axle and then firmly press the tabs into the slots. Swivel removal procedure not the next step. For reference purposes only. Simply place the screwdriver into the opening next to the tab and rotate 90...
29b 29c page 10 29 29a 28 32 in. 82 cm hose attachment push push pull feed hose strap (n), with smooth side up, through square hole in flange. Align the 32” mark with the square hole in flange. N measure 32 inches from the female end of your garden hose. Then lay the hose across the top of the reel ...
33 page 11 32 31 30 click click click reel in hose. Clicking sound during rewind is normal. Feed female end of garden hose through flange opening. Attach garden hose to brass swivel. Hand tighten. J insert kink-free spring (j) into garden hose. Note: the kink-free spring (j) is designed to prevent a...
Brake adjustment page 12 2007 © eley corporation p.O. Box 22640 lincoln, ne 68542 patent pending congratulations! Assembly and installation are complete. Enjoy your hose reel. 1/4 turn m test brake tension, (or drag), by pulling out a few feet of hose. If the brake effectively slows the reel, and pr...
