Instruction manual instruction manual this radio control model is not a toy! Before beginning assembly, please read this manual thoroughly. The contents are subject to change without prior notice due to product improvements and specification changes. 本產品為高性能模型非一般玩具，組裝與操作前請詳閱本產品說明書。 本套件所附之零件可能跟圖示有所差異...
-2- introduction / 簡介 thank you for purchasing the thunder tiger raptor e820 r/c helicopter. This new helicopter is the latest innovation by thunder tiger. It has the perfect combination of flying stability and the agility for 3d flying. This helicopter is an excellent choice for flying enthusiasts ...
-3- flight safety checklist / 飛行前安全確認工作項目 post flight inspection / 飛行結束安全檢查事項 caution / 注意事項 1. Make sure that the transmitter battery is fully charged before flying. 2. Make sure all control surfaces are operated properly before flying. 3. Do a range check of the radio before the first flight. The ...
-4- screw driver 各種規格的螺絲起子 7mm 5.5mm 7mm 8mm hobby knife 美工刀 c.A glue 瞬間膠 grease 潤滑油 epoxy 環氧樹酯 hex wrench 六角板手 threadlocker 螺絲防鬆膠 needle nose pliers 尖嘴鉗 wrench 開口板手 5.5mm ball link pliers 拆連桿頭的專用鉗子 nipper 斜口鉗 scissors 剪刀 metric 4-way wrench 十字套筒板手 5.5mm 7mm 8mm 10mm socket drivers 套筒螺絲起子 tools requ...
Apply c.A glue 使用快乾膠黏合 assemble as many times as specified 依指示組裝所需數量 assemble left and right side the same way 左右側組件相同 assemble in right order 依標示順序組裝 drill holes with the specified diameter 依標示尺寸鑽孔 hint 組裝提示 must be purchased separately 改裝品需另購 cut off shaded portion 依標示部分裁切 ensure smooth, non-bindi...
-6- main rotor system / 主旋翼機構組裝 bag a apply threadlocker 使用螺絲防鬆膠 assemble left and right side the same way 左右側組件相同 bearing, d8xd16xw5 滾珠軸承, d8xd16xw5 thrust bearing, d8xd16xw5 止推軸承, d8xd16xw5 thrust collar, d8xd12xw0.5 止推軸環, d8xd12xw0.5 socket screw, m3x6 內六角螺絲, m3x6 linkage ball(a) 內六角連接頭螺絲(a) wash...
Apply threadlocker 使用螺絲防鬆膠 assemble left and right side the same way 左右側組件相同 ensure smooth, non-binding movement when assembling 確認組件靈活度 no. 15 16 17 18 19 20 21 22 23 24 25 26 26-1 26-2 qty description 名稱 thrust collar, d8xd12xw1.0 thrust collar, d8xd12xw0.2 thrust collar, d8xd12xw0.1 spindle outer...
-8- tail boom bracket assembly / 尾管固定座組裝 bag b pin, φ2x12 固定銷, φ2x12 bearing, d5xd13xw4 滾珠軸承, d5xd13xw4 set screw, m3x4 無頭內六角螺絲, m3x4 bearing, d12xd18xw4 滾珠軸承, d12xd18xw4 bevel collar, d12xd13.6xw11.85 傘齒軸環, d12xd13.6xw11.85 self-tapping screw, m2.6x16 扁圓自攻螺絲(粗) socket screw, m3x25 內六角螺絲, m3x25 lock...
Left frame 左側板 right frame 右側板 no. 1 2 3 4 5 6 7 8 9 10 qty description 名稱 碳纖側板-左 碳纖側板-右 機身固定柱 星型螺絲, m3x8 控制臂軸承座 軸承座螺帽 控制臂固定座 沈頭內六角螺絲, m2.5x5 扁圓自攻螺絲(粗), m2.6x12 腳架固定座 side frame-l side frame-r canopy retaining post torx screw, m3x8 elevator washer mount set nut control arm base sink socket screw, m2...
-10- main frame / 本體組裝 no. 1 2 3 4 5 6 7 qty description 名稱 no. 8 9 10 11 12 13 qty description 名稱 油門伺服機固定架 星型螺絲, m3x8 側板支柱 沈頭內六角螺絲, m3x10 墊圈, d3xd8xw1.4 止鬆螺帽, m3 電池盒軸襯 墊圈, d3xd9xw2 碳纖下側板 電池盒支柱 支撐架固定座 無頭內六角螺絲 機身固定柱(長) radio tray torx screw, m3x8 frame spacer sink socket screw, m3x10 washer, d3xd8xw1...
Torx srcew, m3x8 星型螺絲, m3x8 socket srcew, m3x10 內六角螺絲, m3x10 set screw, m3x18 無頭內六角螺絲 , m3x18 linkage ball(a) 內六角連接頭螺絲(a) bearing, d2.5xd7xw3.5 滾珠軸承, d2.5xd7xw3.5 socket srcew, m2.5x8 內六角螺絲, m2.5x8 (8) (6) (7) (9) (9) (7) (10) (10) no. 1 2 3 4 5 6 7 qty description 名稱 星型螺絲, m3x8 內六角螺絲, m3x10 無頭內六角螺絲...
Lower the upper main shaft bearing block to eliminate the play after securing all screws. 鎖固定位螺絲後，將上主軸軸承座下 壓以消除間隙。 socket screw, m4x8 內六角螺絲, m4x8 socket screw, m2.5x6 內六角螺絲 , m2.5x6 line up the holes of the autorotation tail drive gear, one way bearing shaft & main shaft, and then insert the socket ...
Assemble left and right side the same way 左右側組件相同 skid pipe end cap 圓管塞 set screw, m4x4 無頭內六角螺絲, m4x4 socket screw, m4x14 內六角螺絲, m4x14 landing skid brace skid pipe skid pipe end cap 腳架 底座圓管 圓管塞 2 2 4 no. 1 2 3 qty description 名稱 set screw, m4x4 socket screw, m4x14 no. 4 5 qty description 名稱 4 4 無頭內六...
(4) (2) (5) (1) (3) (4) (2) (5) -14- control arm set / 控制臂組組裝 qty description 名稱 no. 1 1-1 1-2 1-3 1-4 1-5 control arm set-l control arm-l link ball socket screw, m2x8 linkage ball(a) bearing, d8xd12xw3.5 側轉控制臂座組-左 側轉控制臂座-左 連結球座 內六角螺絲, m2x8 內六角連接頭螺絲(a) 滾珠軸承, d8xd12xw3.5 1 1 2 2 4 4 no. 2 3 3-1 4 5 q...
Metal tail grip washer, d7.5xd10xw0.3 washer, d7.5xd5xw0.3 thrust bearing, d5xd10xw4 bearing, d5xd10xw4 tail rotor hub set screw, m3x3 washer, d3xd7xw0.5 torx screw, m3x8 tail pitch control link 2 2 2 2 2 1 2 2 2 2 no. 1 2 3 4 5 6 7 8 9 10 qty description 名稱 金屬尾旋翼轉座 止推軸環, d7.5xd10xw0.3 止推軸環, d7.5xd5...
(18) (18) (14) (13) (17) (13) (16) (19) (19) (12) (8) (9) (15) (7) qty description 名稱 1 2 1 1 1 2 1 1 1 1 no. 1 2 3 4 5 6 7 8 9 10 metal tail unit housing bearing, d12xd18xw4 collar, d16.5xd18xw6.83 collar, d12xd13xw6.85 tail input bevel flange bearing, d5xd13xw4 tail output bevel pin, φ2x12 set scr...
No. 1 2 3 4 5 6 7 8 9 10 11 qty description 名稱 tail drive shaft tail drive shaft brg lock nut, m2.5 tail drive shaft linker socket screw, m2.5x12 carbom tail boom torx screw, m3x8 tail stopper socket screw, m3x10 carbon vertical fin metal tail boom support bracket 尾驅動軸 尾驅動軸軸套組 止鬆螺帽, m2.5 尾驅動連接棒 內六角螺...
-18- servo installation / 伺服機裝配 attach the servos onto the servo trays of main frame set as drawing. 參考圖示將伺服機裝入主側板組上伺服機座。 no. 1 2 3 4 5 qty description 名稱 伺服機擺臂軸套 伺服機擺臂 尾舵伺服機擺臂 連接球座 伺服機墊片 servo horn collar servo horn rudder servo horn link ball servo mounting 4 3 1 7 8 no. 6 7 8 9 10 qty description...
(3) (6) (6) (5) (4) (4) (5) (3) (2) (3) (1) (2) no. 1 2 3 qty description 名稱 no. 4 5 6 qty description 名稱 1. You may need to adjust the linkage to ensure the blade tracking. Please refer page 27:blade tracking adjustment. 2. Install the main blades with the socket screw. Do not over tighten and ensu...
Flat screw, m3x10 扁平頭螺絲, m3x10 collar, d3xd4xw3.1 軸套, d3xd4xw3.1 no. 1 2 3 qty description 名稱 battery tray battery tray catch collar, d3xd4xw3.1 電池座 電池座夾扣 軸套, d3xd4xw3.1 1 1 2 no. 4 5 qty description 名稱 flat screw, m3x10 spring 扁平頭螺絲, m3x10 拉伸彈簧 2 2 -20- electronic device & battery tray / 電子設備及電池座組裝...
Button phillips tapping screw, m3x12 扁圓自攻螺絲(粗), m3x12 no. 1 2 3 qty description 名稱 fiberglass canopy, red rubber grommet button phillips tapping screw, m3x12 玻纖機殼(紅) 機身固定墊圈 扁圓自攻螺絲(粗), m3x12 1 4 2 no. 4 5 qty description 名稱 body clip b canopy bracket 機身夾扣b 機身固定扣a 1 1 -21- electronic device & canopy /...
-22- radio system setup / 遙控系統設定 swashplate type setting / 十字盤模式設定 choose and activate the swashplate mixing for a 135°ccpm program in your transmitter is the best recommended. Please refer your transmitter manual to find a proper swashplate setting. A 140°ccpm program is also applicable to the heli...
Warning! / 警告! Remember to turn the receiver power off and extract the handle drivers from the helicopter before performing the next procedure. 執行下一設定步驟前，請記得關閉接收機電源，並自機體上移除手工具。 90° 0。 3. Mechanism neutral position setting / 中立點設定 -23- the innovative quick-calibration system helps you to get a mechan...
Ensure there is none of the control bind at full travel before going through following setting procedures. Next, refer the illustrations below to check the direction of servo & swashplate with a given transmitter input. Adjust the servo reversing function in your transmitter if incorrect. 繼續設定前，請確認伺...
-25- tail control & gyro setup / 尾舵控制及陀螺儀控制 it is recommended to use a heading lock gyro. With a heading lock gyro, you may not use the trim and the revolution mixing function of tail control. Mount the servo arm for the moment and check the movement of the tail servo: 1. While giving the right rudd...
-26- throttle & pitch curve setting / 油門及螺距曲線設定 the following is the setting up data of pitch curve and throttle curve for your reference only. Please ask an experienced pilot to help if you have never done this before. 下列參數設定僅供參考，請依實際狀況進行調整，或詢求有經驗的玩家協助。 ■ novice / 初學者設定 ■ 3d flight / 進階玩家設定 1. Too ...
-27- blade tracking adjustment / 主旋翼軌跡調整 1. Use a color tape at the tip of main blades for tracking identification easily. 2. Increase the main blade speed to just before the helicopter lifts-off. 3. Observe which blade appears to be lower than the other, and increase the pitch of the lower blade on...
-28- after flight checklist / 飛行後的檢查項目 (1) check every screw and bolt to make sure none has loosened due to vibration. (2) check every rotating and movable part to ensure they still move smoothly and normally. (3) clean off the exhaust residue from the muffler, engine, and helicopter. (4) check all ...
Pv0041 ball link 單頭連接桿 pv0062 rubber grommets (white) 機身固定墊圈組 pv0126-1 spindle 固定軸 pv0172 thrust bearing, d8xd16xw5 止推軸承組, d8xd16xw5 pv0588 canopy retaining post set 機身固定柱 pv0589 control arm base 控制臂固定座 pv0586 side frame-l 碳纖側板-左(單片) pv0587 side frame-r 碳纖側板-右(單片) pv0195 tail drive shaft bearing set...
Pv1503 metal flybarless head button 金屬無平衡翼煞車盤 pv1379 linkage ball screw set 球頭螺絲組 pv1432 thrust bearing, d5xd10xw4 止推軸承組,d5xd10xw4 pv1505 metal flybarless main rotor hub set 金屬無平衡翼主旋翼固定座 pv0596 metal tail unit housing set 金屬尾座組 pv0597 fiberglass canopy 玻纖機殼 pv0619 3d damper set 3d避震墊圈組 pv0595 metal ...
Pv1533-1 flybarless linkage rod set 無平衡翼連接桿組 pv1543 main gear,111t 主齒輪(111t) pv1542 metal servo mount 金屬伺服機固定座 pv1541 rear tail helical bevel gear set 後尾螺旋傘齒輪組 pv1540 front tail bevel gear set 前尾傘齒輪組 pv1539 tail drive gear-26t 尾驅動齒輪26t pv1538 tail drive gear shaft 尾驅動齒輪軸 pv1537 tail drive gear set 尾...
Pv1575 radio tray 油門伺服機固定架 pv1589 metal tail boom support bracket 金屬尾管支撐固定座 pv1587 rod guide set 推拉桿固定環組 pv1584 landing skid brace 腳架 pv1583 landing skid set 腳架組 pv1582 metal rudder servo horn 金屬尾舵伺服機擺臂 pv1581 collar set 軸環組 pv1579 battery tray set 電池座組 pv1576 metal frame spacer 金屬側板支柱 pv1578 batter...
Pv1604 servo mounting set 伺服機墊片組 pv1718 tail drive shaft 尾驅動軸組 pv1717 carbon tail boom 碳纖尾管 pv1629 torx driver tip 星型圓棒 pv1623-f servo horn collar(futaba) 伺服機擺臂軸套(futaba) pv1613 self tapping screw set 扁圓自攻螺絲組 pv1612 pin set 固定銷組 pv1611 flange bearing,d5xd13xw4 凸緣軸承組,d5xd13xw4 pv1605 rotor spacer 主旋翼...
-34- spare parts / 零件包 pv0212 pv0213 pv0214 pv0215 pv0216 pv0218 pv0220 pv0223 pv0256 pv0637 pv0777 pv1614 內六角螺絲, m3x10 內六角螺絲, m3x12 內六角螺絲, m3x14 內六角螺絲, m3x18 內六角螺絲, m3x25 內六角螺絲, m3x8 內六角螺絲, m4x12 內六角螺絲, m4x8 內六角螺絲, m3x6 內六角螺絲, m2.5x12 內六角螺絲, m2x8 內六角螺絲組 socket screw, m3x10 (20) socket screw, m3x12 ...
Pv1621 landing skid brace, black 腳架組, 黑 pv1622 carbon horizontal fin 碳纖水平安定面 pv1616 reinforced metal motor pinion block, 8mm 強化金屬馬達齒輪固定座,8mm pv1630 reinforced metal motor pinion block, 6mm 強化金屬馬達齒輪固定座,6mm pv1547 metal motor mount 金屬馬達固定座 pv0598 u type motor mount(6mm) u型馬達座組(6mm) electronic device &...
Main rotor head main gear set -36- exploded view / 爆炸圖檢索 pv1503 pv1505 pv0172 pv0620 pv1627 pv0126-1 pv0619 pv1627 pv1516 pv0175 pv0580 pv0581 pv0579 pv0621 pv1521 pv1530 pv1532 pv1523 pv1533-1 pv1525 pv1529 pv1527 pv1543 pv1545 pv1544 pv1546.
Main frame -37- exploded view / 爆炸圖檢索 pv1542 pv0586 pv1576 pv0587 pv0588 pv0588 pv1567 pv0588 pv1578 pv1564 pv1567 pv0592 pv0588 pv1567 pv1569 pv1569 pv0592 pv0589 pv1573 pv1575 pv1576 pv1576 pv1578 pv1578 pv0582 pv1572 pv1570 pv1578 pv1564 pv0589 power system pv1579 pv0584 pv0585 pv0583 must be pur...
Arms & skid -38- exploded view / 爆炸圖檢索 pv0590 pv1583 pv1584 pv1623-f pv1603 pv1604 pv1598 pv1598 pv1603 pv1534 pv1613 pv1603 pv1604 pv1604 pv0591 pv1614 pv1535 pv0590 pv1613 pv1534 pv1623-f pv1535 pv1623-f pv1536 pv1244 pv1576 pv0216 pv0214 pv1537 pv1538 pv1539 pv1540 pv1581 pv0197 pv0050 pv1612 mus...
Tail unit -39- exploded view / 爆炸圖檢索 pv1718 pv1719 pv1582 pv1604 pv1623-f pv0195 pv0593 pv0594 pv1587 pv1589 pv1593 pv0595 pv1594 pv1593 pv1595 pv1596 pv1611 pv1598 pv1541 pv0425 pv0215 pv1717 pd1244 pv0596 pv1600-1 must be purchased separately 改裝品需另購.
-40- memo.
