1. DL manuals
  2. Ratoc Systems
  3. Computer Hardware
  4. CB32U
  5. User manual

Ratoc Systems CB32U User manual

Manual is about: Ultra Wide SCSI (FAST-40) CardBus PC Card

Summary of CB32U

  • Page 1

    Ultra wide scsi (fast-40) cardbus pc card cb32u user’s guide april 2002 rev. 3.0

  • Page 2: Cb32U

    Cb32u 1. Introduction........................................................................... 1 1-1. Package confirmation ..................................................................................................... 1 1-2. System requirements .................................................

  • Page 3

    5. Installing windows 95/98 ................................................... 50 5-1. Making a windows 95 startup floppy disk .................................................................... 51 5-2. Making a windows 98 startup floppy disk...........................................................

  • Page 4: 1. Introduction

    1. Introduction 1 1. Introduction this user’s guide describes how to install, use, and troubleshoot the ratoc cb32u ultra wide scsi cardbus pc card(called cb32u in this user’s guide). The information in the readme.Txt file on the floppy disk may include the latest information. Be sure to read the re...

  • Page 5: 2. Setup

    2. Setup 2 2. Setup when you use windows 95, proceed to chapter 2-1. When you use windows 98, proceed to chapter 2-2. When you use windows me, proceed to chapter 2-3. When you use windows nt4.0, proceed to chapter 2-4. When you use windows 2000, proceed to chapter 2-5. When you use windows xp, proce...

  • Page 6: 2-1. Windows 95 Setup

    W indows95 3 2. Setup 2-1. Windows 95 setup here’s how to get started with the cb32u and scsi devices on windows 95: 1. Read the restrictions before you install the cb32u. 2. Install the cb32u into the pc. Refer to chapter 2-1-1. 3. Confirm the installation. Refer to chapter 2-1-2. 4. Remove the cb3...

  • Page 7

    W indows95 4 2. Setup if you find a pcic or compatible pcmcia controller string under the pcmcia socket, your pc card slot may not support cardbus pc cards or cardbus setting may be set disable in the bios of your pc. If cardbus setting is set disable in the bios, select cardbus from disable/pcic co...

  • Page 8

    W indows95 5 2. Setup 3. Grasp the cb32u by the edges with the label facing upward. Insert the cb32u into the slot and push it in until it is firmly seated. If the cb32u can not be firmly seated, check to see if the pc card slot supports cardbus pc cards. If the following window as shown at step 4 d...

  • Page 9

    W indows95 6 2. Setup e. Wait until the pc card (pcmcia) icon appears on the windows taskbar. This icon indicates that the cb32u is recognized. F. Remove the floppy disk from the pc. C. If a message requesting insertion of a floppy disk appears, click ok. D. The copying files... Dialog appears. Type...

  • Page 10

    W indows95 7 2. Setup 2-1-2. Confirming the installation 1. Right-click on my computer. 2. Select properties. You will see the system properties window below. 3. Click the device manager tab. 4. Double-click scsi controllersin the list. 5. Make sure there is a scsi cardbus pc card rex cb32 string wi...

  • Page 11: 2-1-3. Removing The Cb32U

    W indows95 8 2. Setup 2-1-3. Removing the cb32u when you want to remove the cb32u from the pc, you have to follow these steps through: 1. Click the pc card iconon the windows taskbar. 2. Select stop scsi cardbus pc card rex cb32. 3. When the window saying you may safely remove this device appears, y...

  • Page 12: 2-2. Windows 98 Setup

    W indows98 2. Setup 9 2-2-1. Installing the cb32u on windows 98 1. Check to see if your pcmcia controller supports cardbus pc cards. A. Right-click on my computer. B. Select properties. You will see the system properties window below. C. Click the device manager tab. D. Double-click pcmcia socket an...

  • Page 13

    W indows98 2. Setup 10 if you find a pcic or compatible pcmcia controller string under the pcmcia socket, your pc card slot may not support cardbus pc cards or cardbus setting may be set disable in the bios of your pc. If cardbus setting is set disable in the bios, select cardbus from disable/ pcic ...

  • Page 14

    W indows98 2. Setup 11 b. When the following window appears, select the search for the best driver for your device (recommended) option and click next. 3. When the add new hardware wizard window appears a. When the add new hardware wizard window appears, insert the cb32u floppy disk for wi n - dows ...

  • Page 15

    W indows98 2. Setup 12 f. When the following window appears, click finish. G. Wait until the pc card (pcmcia) icon appears on the windows taskbar. This icon indicates that the cb32u is recognized. H. Remove the floppy disk from the pc. To confirm the installation of the driver, refer to chapter 2-1-...

  • Page 16: 2-2-2. Removing The Cb32U

    W indows98 2. Setup 13 2-2-2. Removing the cb32u when you want to remove the cb32u from the pc, you have to follow these steps through: 1. Click the pc card iconon the windows taskbar. 2. Select stop scsi cardbus pc card rex cb32. 3. When the window saying you may safely remove this device appears, ...

  • Page 17: 2-3. Windows Me Setup

    14 w indows me 2. Setup 2-3. Windows me setup here’s how to get started with the cb32u and scsi devices on windows me: 1. Read the restrictions before you install the cb32u. 2. Install the cb32u into the pc. Refer to chapter 2-3-1. 3. Confirm the installation. Refer to chapter 2-1-2. 4. Remove the c...

  • Page 18

    15 w indows me 2. Setup e. Double-click the cardbus controller name string to show the property window. If this device is working properly appears under the device status, you can use the cb32u. 2. Grasp the cb32u by the edges with the label facing upward. Insert the cb32u into the slot and push it ...

  • Page 19

    16 w indows me 2. Setup 3. When the add new hardware wizard window appears a. When the add new hardware wizard window appears, insert the cb32u floppy disk for windows 98/95 and select the automatic search for a better driver(recommended) option. Click next. B. When the following window appears, cli...

  • Page 20: 2-3-2. Removing The Cb32U

    17 w indows me 2. Setup 2-3-2. Removing the cb32u when you want to remove the cb32u from the pc, you have to follow these steps through: 1. Click the pc card iconon the windows taskbar. 2. Select stop scsi cardbus pc card rex cb32. 3. When the window saying you may safely remove this device appears,...

  • Page 21: 2-4. Windows Nt4.0 Setup

    2. Setup 18 w indows nt4.0 2-4. Windows nt4.0 setup here’s how to get started with the cb32u and scsi devices on windows nt4.0: 1. Read the restrictions before you install the cb32u. 2. Install the cb32u driver. Refer to chapter 2-4-1. 5. Confirm the installation. Refer to chapter 2-4-2. 6. Remove t...

  • Page 22

    2. Setup 19 w indows nt4.0 2-4-1. Installing the cb32u driver 1. Turn off your pc and grasp the cb32u by the edges with the label facing upward. Insert the cb32u into the slot and push it in until it is firmly seated. If the cb32u can not be firmly seated, check to see if the pc card slot supports c...

  • Page 23

    2. Setup 20 w indows nt4.0 4. Click the drivers tab and click add. 5. You will see the screen below. Click have disk. 6. You will see the screen below. Type a:\ at copy manufacturer’s files from and click ok..

  • Page 24

    2. Setup 21 w indows nt4.0 7. You will see the screen below. Click ok. 8. You will see the screen below. Click yes..

  • Page 25

    2. Setup 22 w indows nt4.0 2-4-2. Confirming the installation of the cb32u driver follow the steps through to confirm the installation of the cb32u driver. 1. Double-click on the icon on the windows taskbar. 2. Confirm the ultrawide scsi cb32 string is shown. Then, click the property button. 3. You ...

  • Page 26: 2-4-3. Removing The Cb32U

    2. Setup 23 w indows nt4.0 2-4-3. Removing the cb32u when you want to remove the cb32u from the pc, you have to follow these steps through: 1. Shut down windows nt4.0. 2. Turn off the pc and remove the cb32u..

  • Page 27: 2-5. Windows 2000 Setup

    2. Setup 24 w indows 2000 2-5-1. Installing the cb32u on windows 2000 1. Check to see if your pcmcia controller supports cardbus pc cards. A. Right-click on my computer. B. Select properties. You will see the system properties window below. C. Click the hardware tab. 2-5. Windows 2000 setup here’s h...

  • Page 28

    W indows2000 2. Setup 25 d. Click the device manager button. E. Double-click pcmcia adapters and make sure there is a cardbus controller name string without “!” or “x” marks. If you find a intel pcic compatible pcmcia controller string under the pcmcia adapters, your pc card slot may not support car...

  • Page 29

    2. Setup 26 w indows 2000 f. Double-click the cardbus controller name string to show the property window. If this device is working properly appears under the device status, you can use the cb32u. 2.Grasp the cb32u by the edges with the label facing upward. Insert the cb32u into the slot and push it...

  • Page 30

    W indows2000 2. Setup 27 3. You will see the screen below. Click next. 4. You will see the screen below. Select the search for a suitable driver for my device(recommended) option and click next. 5. You will see the screen below. Insert the cb32u floppy disk for windows 2000. Then, select the floppy ...

  • Page 31

    2. Setup 28 w indows 2000 6. You will see the screen below. Click next. 7. You will see the screen below. Click yes. 8. You will see the screen below. Click finish. 9. Wait until the pc card (pcmcia) icon appears on the windows taskbar. This icon indicates that the cb32u is recognized. 10. Remove th...

  • Page 32

    W indows2000 2. Setup 29 2-5-2. Confirming the installation 1.Right-click on my computer and select properties.You will see the screen below. Click the hardware tab. Click the device manager button. 2.You will see the screen below.Double-click scsi pc card rex-cb32 win2k..

  • Page 33: 2-5-3. Removing The Cb32U

    2. Setup 30 w indows 2000 2-5-3. Removing the cb32u when you want to remove the cb32u from the pc, you have to follow these steps through: 1. Click the pc card iconon the windows taskbar. 2. Select stop scsi pc card rex-cb32 win2k. 3. When the window saying you may safely remove this device appears,...

  • Page 34: 2-6. Windows Xp Setup

    W indows xp 31 2-6-1. Installing the cb32u on windows xp 1. Check to see if your pcmcia controller supports cardbus pc cards. A. Right-click on the start button. B. Right-click on my computer and select properties. You will see the system properties window below. C. Click the hardware tab. D. Click ...

  • Page 35

    W indows xp 32 e. Double-click pcmcia adapters and make sure there is a cardbus controller name string without “!” or “x” marks. If you find a intel pcic compatible pcmcia controller string under the pcmcia adapters, your pc card slot may not support cardbus pc cards or cardbus setting may be set di...

  • Page 36

    W indows xp 33 2.Grasp the cb32u by the edges with the label facing upward. Insert the cb32u into the slot and push it in until it is firmly seated. If the cb32u can not be firmly seated, check to see if the pc card slot supports cardbus pc cards. If the following window as shown at step 3 does not ...

  • Page 37

    W indows xp 34 5. You will see the screen below. Select scsi and raid controllers and click next. 6. You will see the screen below. Select have disk... And click next. 7. You will see the screen below. Type a:\ at the copy manufacturer’s files from and click ok..

  • Page 38

    W indows xp 35 8. You will see the screen below. Click next. 9. You will see the screen below. Click continue anyway. 10. You will see the screen below. Click finish. 11. Wait until the pc card (pcmcia) icon appears on the windows taskbar. This icon indicates that the cb32u is recognized. 12. Remove...

  • Page 39

    W indows xp 36 2-6-2. Confirming the installation 1.Open system properties.You will see the screen below. Click the hardware tab. Click the device manager button. 2.You will see the screen below.Double-click scsi pc card rex-cb32 win2k..

  • Page 40: 2-6-3. Removing The Cb32U

    W indows xp 37 3. You will see the screen below.Click the general tab.If this device is working properly appears under the device status, you have installed the cb32u driver correctly. 2-6-3. Removing the cb32u when you want to remove the cb32u from the pc, you have to follow these steps through: 1....

  • Page 41: 3. Using Scsi Devices

    38 3. Using scsi devices 3. Using scsi devices 3-1. Connecting a scsi device 1. Attach an external active terminator to the scsi device, as shown below. If the scsi device has an internal terminator and the switch, set it on state. Refer to the scsi device manual if you are not sure how to activate ...

  • Page 42

    39 3. Using scsi devices 5. Attach the scsi connector into the scsi device. 6. Turn on all the scsi devices connected to the cb32u. 7. Wait until access led of the scsi devices goes off. 8. Turn your pc on and insert the cb32u into your pc..

  • Page 43

    40 3. Using scsi devices 3-2. Confirming the scsi device connection if you use windows 95/98/me/2000/xp, follow the steps through: if you use windows nt4.0, proceed to the next page. 1. Open device manager. Make sure the scsi device name string appears in the device manager. The following device man...

  • Page 44

    41 3. Using scsi devices if you use windows nt4.0, follow the steps below. 1. Open scsi adapters in the control panel. 2. You will see the following window. Click scsi cardbus pc card rex cb32 to confirm your scsi device is connected to the cb32u correctly. Select the scsi device name and click prop...

  • Page 45: 4. Installing Scsi Utility

    42 4. Installing scsi utility 4. Installing scsi utility to install scsi utility, follow the steps through: 1. If you use windows 95/98/me, insert the cb32u floppy disk for windows 95/98 into the floppy drive. If you use windows nt4.0, insert the cb32u floppy disk for windows nt4.0 into the floppy d...

  • Page 46: 4-1. Format Utility

    43 4.Installing scsi utility you can format a hdd, jaz, mo, zip drive, etc., with this uiliity. Note: you can not format cd-r, cd-rw or dvd-ram. Follow these steps through to format your scsi drive. 1. Make sure the scsi device is connected and powered on. 2. If the device is a removable disk and a ...

  • Page 47

    44 4. Installing scsi utility 5.You will see the window below. Select initialize/format media from the edit menu. 6.You will see the window below. Choose format type. If you want to do low level format simultaneousely, check the low level format check box. Then click ok..

  • Page 48

    45 4.Installing scsi utility 7. A. If you have selected ibm-pc/at fdisk format at step 6, the message box saying [you should create partition next] appears. Click ok. You will see the screen shown at step 5. Select create partition from the edit menu to create partition. You will see the screen belo...

  • Page 49

    46 4. Installing scsi utility 4-2. Rexscsi configuration utility normally you don’t need to use this configuration utility. But, when you use the following scsi devices, you need to use this configuration utility to change scsi configuration. -fujitsu m2512a/m2513a mo drive (you need to set 10mb/s a...

  • Page 50

    47 4.Installing scsi utility 4. Scsi configuration window will appear. If you connect fujitsu mo(m2512a, m2513a), select 10mb/sec.At maxtransfer. If you connect an asynchronous scanner device, don’t put check mark at sync. Transfer enable. Then click write. Hostadapter scsi id default setting is 7.I...

  • Page 51

    48 4. Installing scsi utility 4-3. Scsi device check utility with this utility, you can check whether your scsi device connected to the cb32u is recognized or not. Follow these steps through to check it. 1. Connect your scsi device to the cb32u and turn on the scsi device. 2. Click the [start] butto...

  • Page 52

    49 4.Installing scsi utility when you double-click on the scsi device name in the device list, you will see information on it as shown below..

  • Page 53: 5. Installing Windows 95/98

    Ms-dos 50 5. Installing windows 95/98 5. Installing windows 95/98 this chapter explains how to make a startup floppy disk and how to access to a scsi cd-rom connected to the cb32u with the startup floppy disk. If you can accees to a scsi cd-rom with the startup floppy disk, you can install windows 9...

  • Page 54

    Ms-dos 51 5. Installing windows 95/98 5-1. Making a windows 95 startup floppy disk this section gives you information on how to make a windows 95 startup flopply disk. With the startup floppy disk, you can access to the scsi cd-rom drive connected to the cb32u and install windows 95 from the scsi cd...

  • Page 55

    Ms-dos 52 5. Installing windows 95/98 5-2. Making a windows 98 startup floppy disk this section gives you information on how to make a windows 98 startup flopply disk. With the startup floppy disk, you can access to the scsi cd-rom drive connected to the cb32u and install windows 98 from the scsi cd...

  • Page 56

    Ms-dos 53 5. Installing windows 95/98 ----------------------------- cbenable.Exe parameter -------------------------- format: device = : \ cbenable.Exe [irq] [io] [mem] parameter [irq] set irq number used by the cb32u. If you don’t set anything to this parameter, ah(10) is set as irq number. If this...

  • Page 57

    Ms-dos 54 5. Installing windows 95/98 --------------------------- aspcb32.Sys parameter ------------------------------ format: device = : \ aspcb32.Sys [/l] [/d] parameter [/l] lun(logical unit no). When you set this parameter, all lun will be searched. If you don’t set anything to this parameter, o...

  • Page 58

    Ms-dos 55 5. Installing windows 95/98 ----------------------------- rexcd.Sys parameter ------------------------------ rexcd.Sys is a cd-rom driver based on aspi manager for dos. Format: device = : \ rexcd.Sys [/d:][/u:1] [/scanid:id + id + …… ] [/noscanid: id + id + ……][/n:1][/e][/ha:0] [/noprefetc...

  • Page 59

    Ms-dos 56 5. Installing windows 95/98 --------------------------- rexdiskw.Sys parameter ----------------------------- rexdiskw.Sys is a driver for hard disk/jaz/zip drives based on aspi manager for dos. Rexdiskw.Sys can use only fat12, fat16 file system. Rexdiskw.Sys can not use fat32 file system. ...

  • Page 60: 6. Installing Windows 2000

    W indows2000 6. Installing windows 2000 57 6. Installing windows 2000 this chapter explains how to install windows 2000 from a scsi cd-rom connected to the cb32u. If you upgrade windows 98 or windows nt4.0 to windows 2000, refer to chapter 6-1. If you install a new copy of windows 2000(clean install...

  • Page 61

    W indows2000 6. Installing windows 2000 58 6-2. Installing a new copy of windows 2000 from windows 98/nt4.0 follow these steps through: 1.Start windows 98 or windows nt4.0. 2.You will see setup program of windows 2000 running from the scsi cd-rom connected to the cb32u. 3.When setup starts, you can ...

  • Page 62: 7. Linux

    59 7. Linux linux 7. Linux 7-1. How to install the driver for linux this chapter explains how to install the cb32u driver for linux. To install the driver, development module is required for your linux. If you do not know how to set up development module, ask the distributor of your linux. If you wa...

  • Page 63

    60 7. Linux linux 3.Making driver module (1)copying the driver source file copy the driver source file to the directory which includes pcmcia client driver source. (the directory normally means pcmcia-cs clients directory) if there is the extracted driver source file in the directory /root/cb32, typ...

  • Page 64

    61 7. Linux linux 4.Installing the driver module (1)copying the driver module file (cb32_cb.O) copy the driver module file named cb32_cb.O to the directory which includes module related to pcmcia. # cp cb32_cb.O /lib/modules/2.2.12-32/pcmcia/. (2)editing pcmcia database (/etc/pcmcia/config) add the ...

  • Page 65

    62 7. Linux linux 7-2. Scsi configuration utility for linux:inicconf this section explains the instructions to set up the cb32u on redhat linux 6.1. Login as as an root user before setting up the cb32u scsi configuration utility. 1.Copying the file to your hdd insert the cb32u for linux into the flo...

  • Page 66

    63 7. Linux linux 4. Compiling inicconf.C execute make and compile inicconf.C. # make inicconf note: you might see some warning messages. If you can build inicconf, don't worry about it. 5. Copying inicconf copy inicconf to the directory where you can execute it. (for example : /usr/local/bin ) # cp...

  • Page 67

    64 7. Linux linux executing inicconf [format] inicconf [command, parameter] -v to show the status of current setting -x to show the value of eeprom (hex) --disc_all= to set enable/disable of disconnect for all scsi id (for example) --disc_all=on : enable disconnect with scsi-id 0-15 --disc_all=off :...

  • Page 68

    65 7. Linux linux -wide_all= to set enable/disable of wide negotiation for all scsi id (for example) --disc_all=on : enable wide negotiation with scsi-id 0-15 --disc_all=off : disable wide negotiation with scsi-id 0-15 --wide= to set enable/disable of wide negotiation for specific scsi id (for examp...

  • Page 69

    66 7. Linux linux [example] # inicconf -v pci31/33, cb32 scsi configuration utility .... Initio inic-850 on ratoc cb32 found. I/o base = 0800 view eeprom setting: id-0 id-1 id-2 id-3 id-4 id-5 id-6 id-7 enable disconnect : on off off on on on on on syncronous transfer : 20mb 10mb 40mb 40mb 40mb 40mb...

  • Page 70: 8. Troubleshooting

    67 8. Troubleshooting 8. Troubleshooting 8-1. Deleting the cb32u driver completely if you use windows 95/98/me, refer to chapter 8-1-1. If you use windows nt4.0, refer to chapter 8-1-2. If you use windows 2000, refer to chapter 8-1-3. 8-1-1. Deleting the cb32u driver on windows 95/98/me if you faile...

  • Page 71

    68 8. Troubleshooting 8-1-2. Deleting the cb32u driver on windows nt4.0 if you failed to install the cb32u driver and want to re-install it from the start, delete it first. Follow the steps through to delele the cb32u driver completely. 1. Remove the cb32u from the scsi adapters. A. Open [scsi adapt...

  • Page 72

    69 8. Troubleshooting 8-1-3. Deleting the cb32u driver on windows 2000 if you failed to install the cb32u driver and want to re-install it from the start, delete it first. Follow the steps through to delele the cb32u driver completely. 1. Remove the cb32u from the device tree. A. Right-click on my c...

  • Page 73

    70 8. Troubleshooting 8-2. Updating the cb31u driver for windows95/98 1. Download the latest driver from the ratoc web site.(http://www.Ratocsystems.Com/english/) 2. Make the latest driver floppy disk. A. Download cb32u_xx.Exe (tentative name) into an empty folder on the hard disk drive. B. Double-c...

  • Page 74

    71 8. Troubleshooting e. Click the properties button, and then select the driver tab. F. Check the date before updating the driver. G. Click the update driver... Button. If your windows is windows 95, follow 4. To update the driver for windows 95 procedure. If your windows is windows 98, follow 4. T...

  • Page 75

    72 8. Troubleshooting c. If a message requesting insertion of a floppy disk appears, click ok. D. When copying files... Dialog appears, type a:\ for the source of files and click ok. E. You have finished updating the driver. Remove the floppy disk from the pc. Proceed to step 5. 4. To update the dri...

  • Page 76

    73 8. Troubleshooting 4. To update the driver for windows 98. A. When the update device driver wizard window appears, click next. B. When the following window appears, select thesearch for a better driver than the one your device is using now.(recommeded) option and click next. C. When the following...

  • Page 77

    74 8. Troubleshooting f. When the following window appears, click finish. You have finished updating the driver. G. Remove the support floppy disk from the pc. Proceed to step 5. E. When the following window appears, click next. D. When the following window appears, select the the updated driver (re...

  • Page 78

    75 8. Troubleshooting 5. Confirm the driver is updated. A. In the scsi cardbus pc card rex cb32 properties window,click the driver tab. B. Make sure the date is later than the date you checked in the step 3-f before. C. Click thedriver file details...Button. D. Check the file version of the cb32u dr...

  • Page 79

    76 8. Troubleshooting 8-3. If my laptop is made by toshiba i can use 16-bit pc card with my laptop made by toshiba, but i can not get a cardbus pc card up and running. 1. Shut down your laptop. 2. Start your computer. 3. Press the esc key at boot time. 4. When check system. Then press [f1] key is di...

  • Page 80

    77 8. Troubleshooting 8-6. The cb32u is registered as pci bridge the cb32u is registered as pci bridge in other devices in device manager window. I have not installed the cb32u driver yet. Remove the pci bridge and restart your pc. Hardware wizard will appear. Install the cb32u driver. 8-7. The cb32...

  • Page 81

    78 8. Troubleshooting 8-10. When i can not finish windows 95/98 if your pc has an usb port and a pc card inserted at the same time, you may not be able to shut down your pc. 1. Disable fast shut down. Refer to the help file for information on how to do it. 2. If you can not resolve this issue at ste...

  • Page 82

    79 8. Troubleshooting 5. Double-click theintel 82371ab/eb pci to usb universal host controller under universal serial bus controllers. 6. Select the resources tab and remove the check mark at the use automatic settings. And double- click input/output range. 7. Set value number larger than 1600 by cl...

  • Page 83

    80 8. Troubleshooting 8-11. When i can not detect a scsi scanner on windowsnt/2000 when i try to start scanner software, i get an error saying failed to detect the scsi scanner. You need to install aspi manager for windows nt4.0 or 2000. To install it, you must be logged on as administrator or have ...

  • Page 84

    81 8. Troubleshooting 8-12. When i can not assign a drive letter i can find the scsi drive name string in the device manager, but the drive icon does not appear in my computer. 1. If your computer is in a network and all the driver letters are used, the drive icon does not appear in my computer. To ...

  • Page 85: 9-1. How to Register

    82 9. Registration and tech-support 9-1. How to register we highly recommend to register yourself as our customer through our on-line registration. 1. On the internet, access our site (http://www.Ratocsystems.Com/english/) 2. Follow window menu guide to register. 3. Fill out the registration form an...

  • Page 86: 10. Specifications

    83 10. Specifications 10. Specifications specifications of the cb32u scsi interface •ultra wide scsi or ultra scsi •single ended scsi pc card •pc card standard compliant cardbus (type ii) data transfer rate •up to 40mb/sec with ultra wide scsi devices (synchronous) •up to 20mb/sec with ultra scsi de...

  • Page 87: Appendix

    Appendix trademarks -windows and ms-dos are registered trademarks of microsoft corporation. -initio corporation has an original copyright of aspi manager, miniport driver. -other brand and product names may be registered trademarks or trademarks of their respective holders. This equipment has been t...