1. DL manuals
  2. Ratoc Systems
  3. Computer Hardware
  4. CBFW3
  5. User Manual

Ratoc Systems CBFW3 User Manual

Manual is about: IEEE 1394 OHCI CardBus PC Card for Windows 98SE/2000/Me & for Mac OS 9.0.4 or Later

Summary of CBFW3

  • Page 1

    Ieee 1394 ohci cardbus pc card for windows 98se/2000/me & for mac os 9.0.4 or later cbfw3 user’s guide rev. 1.0 april 2001.

  • Page 2: Cbfw3 User'S Guide

    Cbfw3 user's guide 1. Introduction........................................................................... 1 1-1. Before using the cbfw3 1 1-2. Package 1 1-3. Features 2 1-4. System requirements 2 1-5.Restrictions 3 1-6.Compatibility with video editing software. 4 2. Setup for windows ..............

  • Page 3

    4. How to use rsdvcap .......................................................... 31 4-1.Main menu 32 4-2.Control bars 33 4-2-1.Camera and audio select bar 33 4-2-2.Camera control bar 33 4-2-3.Video control bar 34 4-3.Application settings 35 4-4.Capturing a video from a dvcam in camera mode 39 4-5.Ca...

  • Page 4

    9. Registration and tech-support.......................................... 83 9-1. How to register 83 9-2. Software update and support 83 10. Options ............................................................................... 84 11. Specifications ...................................................

  • Page 5: 1. Introduction

    1 1. Introduction this user’s guide describes how to install, use, and troubleshoot the ratoc cbfw3 ieee1394(firewire) cardbus pc card for windows and macintosh users. If you purchased windows package, refer to the windows chapter. If you purchased macintosh package, refer to the macintosh chapter. ...

  • Page 6: 1-3. Features

    2 1-3. Features • two external ieee1394 ports are available at card. • ieee-1394.A compatible phy chip is on card. • full backward compatibility to ieee1394-1955 device. • ohci 1.0 fully compliant link chip is on card. • 100, 200 and 400mbps data rate is automatically supported at each ieee1394 port...

  • Page 7: 1-5.Restrictions

    3 1-5.Restrictions for windows users •if the following cardbus bridge chip name is the same as your laptop uses, you can not use the cbfw3 with your laptop. -ricoh rl5c465 cardbus controller -ricoh rl5c466 cardbus controller -cirrus logic pd6832 cardbus controller if your cardbus bridge name is rico...

  • Page 8

    4 for windows users microsoft standard wdm dv filter drivers captures dv data stream and save as an avi file which consists with original dv data stream. This dv data stream requires 3.6mb/ sec and includes 720x480 resolution video data(ntsc). Also, the file size is restricted up to 4gb (about 19 mi...

  • Page 9

    5 * 1 for macintosh users you can use the following video editing software with the cbfw3. (as of march in 2001) for more information, contact the manufacturer of the software. Data import from a dv device v ideo editing controlling a dv device exporting to a dv device manufacturer software adobe pr...

  • Page 10

    6 if you are a windows user, go to the chapter 2 to set up the cbfw3. If you are a macintosh user, go to the chapter 7 to set up the cbfw3..

  • Page 11: 2. Setup For Windows

    7 2. Setup for windows to use the cbfw3 on windows, follow the steps. 1.Insert the cbfw3 into the pc card slot. Refer to the chapter 2-1. 2.Install the ohci driver. Refer to the chapter 2-2. 3.Connect an ieee1394 device to the cbfw3. If you connect a dvcam, refer to the chapter 2-3. If you connect a...

  • Page 12: 2-2.Ohci Driver Installation

    Windows 98se 8 2-2-1.Windows 98 se installation to use the cbfw3 on windows 98 se, follow the steps. Step1.Install the ohci driver 1.When the cbfw3 is inserted into the pc card slot, hardware wizard will detect the cbfw3 automatically and you will see the screen below. Click [next]. Then, you need t...

  • Page 13

    Windows 98se 9 5.When the following window appears, click [next]. 4.When the following window appears, select [the updated driver (recommended) texas instruments ohci compliant ieee 1394 host controller]. Then click [next]. 3.When the following window appears, click [next]. (you do not need to check...

  • Page 14

    Windows 98se 10 6.When the following window appears, insert the windows 98 second edition cd-rom into the cd-rom drive. Then click [ok]. 7.If the following window appears, type “d:\win98” or “c:\windows\options\cabs” in the copy files from box, where “d” means the cd-rom drive. After that, click [ok...

  • Page 15

    Windows 98se 11 step3.Installing msdv.Sys update program install msdv update program(252640usa8.Exe) when you use windows 98 se. Follow the steps to install msdv update program. 1.Set the cbfw3 cd-rom into your cd-rom drive. 2.Open [my computer] and double-click cd-rom drive icon. 3.Double-click [wi...

  • Page 16

    Windows 98se 12 step4.Microsoft windows update you should update your windows 98 se to improve performance. To update your windows 98 se, follow the steps. 1.Click start with the left button of the mouse. 2.Select windows update. 3.You will see the screen below. Click product updates. 4.You will see...

  • Page 17

    Windows 2000 13 2-2-2.Windows 2000 installation to use the cbfw3 on windows 2000, follow the steps. Verify the ohci driver installation when you insert the cbfw3 into the pc card slot, the ohci driver is installed automatically by the hardware wizard. To verify the ohci driver installation, follow t...

  • Page 18

    Windows 2000 14 5.If there is a texas instruments ohci compliant ieee 1394 host controller string without any yellow “!” marks or red “x” marks under the ieee 1394 bus host controllers, the ohci driver for the cbfw3 is installed correctly. Check here.

  • Page 19

    Windows me 15 2-2-3.Windows me installation to use the cbfw3 on windows me, follow the steps. Step1.Install the ohci driver 1.When the cbfw3 is inserted into the pc card slot, hardware wizard will detect the cbfw3 automatically and you will see the screen below. Select [automatic search for a better...

  • Page 20

    Windows me 16 step2.Verify the ohci driver installation to verify the ohci driver installation,follow the steps. 1.Click my computer with the right button of the mouse. 2.Select properties. 3.You will see the screen below. Click the device manager tab. 4.Double-click “1394 bus controller”. 5.If ther...

  • Page 21: 2-3.Dvcam  Installation

    17 2-3.Dvcam installation this section describes how to connect a dvcam and install the dv driver. Connect the cbfw3 and a dvcam using the ieee1394 cable as shown below. And turn on the dvcam power switch. You can connect the dvcam without turning off the pc or dvcam. 4pin-6pin ieee1394 cable which ...

  • Page 22

    Windows 98se windows me 18 2-3-1.Windows 98 se/windows me dv driver setup verify the dv driver installation when you connect a dvcam on windows 98 se or windows me, the dv driver will be installed automatically. To verify the dv driver installation, follow the steps. 1.Click my computer with the rig...

  • Page 23

    Windows 2000 19 2-3-2.Windows 2000 dv driver setup verify the dv driver installation when you connect a dvcam on windows 2000, the dv driver will be installed automatically. To verify the dv driver installation, follow the steps. 1.Click my computer with the right button of the mouse. 2.Select prope...

  • Page 24

    Windows 2000 20 5.If there is a “microsoft dv camera and vcr” string without any yellow “!” marks or red “x” marks under the [imaging devices] as shown below, the dv driver is installed correctly. Check here.

  • Page 25

    21 2-4.Desktop ccd camera installation this section describes how to connect a ccd camera and install the driver. Follow the steps to connect a ccd camera. 1.Connect the optional ac adapter(sold separately) to the cbfw3. 2.Connect a ccd camera to the cbfw3 with an ieee1394 6pin-6pin cable. 3.You can...

  • Page 26

    Windows 98se windows me 22 2-4-1.Windows 98se/windows me ccd camera setup when the ccd camera is connected,the ccd camera will be recognized automatically. To verify the ccd driver installation, follow the steps. 1.Click my computer with the right button of the mouse. 2.Select properties. 3.Click th...

  • Page 27

    Windows 2000 23 when the ccd camera is connected, the ccd camera will be recognized automatically. To verify the ccd driver installation, follow steps through. 1.Click my computer with the right button of the mouse. 2.Select properties. 3.You will see the screen below. Click the hardware tab. 4.Clic...

  • Page 28

    Windows 2000 24 5.If there is a ccd camera name string without any yellow “!” marks or red “x” marks under the [imaging devices] as shown below, the driver is installed correctly. Check here.

  • Page 29

    25 2-5.1394 storage installation this section describes how to connect a 1394 storage and install the driver. 1394 storage means hard disk drives(hdds), magneto optical disks(mos), etc. Only windows 98 se, windows 2000 or windows me support such 1394 storage. The cable powered hdd, mo doesn’t work w...

  • Page 30

    Windows 98se windows me 26 when the 1394 hdd is connected, window will install the driver automatically. To verify the 1394 storage driver installation, follow the steps. 1.Click my computer with the right button of the mouse. 2.Select properties. 3.You will see the screen below. Click the device ma...

  • Page 31

    Windows 2000 27 when the 1394 hdd is connected, window 2000 will install the driver automatically. To verify the 1394 storage driver installation,follow the steps. 1.Click my computer with the right button of the mouse. 2.Select properties. 3.You will see the screen below. Click the hardware tab. 4....

  • Page 32

    Windows 2000 28 5.If there is a 1394 hdd name string without any yellow “!” marks or red “x” marks under the [disk drives] as shown below, the 1394 storage driver is installed correctly. Check here.

  • Page 33: 3. Setup Rsdvcap

    29 3. Setup rsdvcap installing rsdvcap/rsdvstill/compressavi 1.Close all programs currently running on your computer. 2.Set the cbfw3 cd-rom in your cd-rom drive. 3.Open [my computer] and double-click cd-rom drive icon. 4.Open [win98se], [win2000] or [winme] folder. If your windows version is window...

  • Page 34

    30 10.You will see the screen below. Select [yes, i want to restart my computer now] and click [finish]. You have now completed installing the capture software. Note if you have installed this software already and start this installer, this installer will delete the software and end. You have to sta...

  • Page 35: 4. How to Use Rsdvcap

    31 4. How to use rsdvcap what is the rsdvcap? This application software has the following functions. •preview and capture video/sound data from a dvcam. •preview and capture video data from a ccd camera. •export media file from a pc to a dvcam. •playback media file. Main menu camera control bar came...

  • Page 36: 4-1.Main Menu:

    32 4-1.Main menu: top menu sub menu description file review movie file end terminate this application. Setting dv batch capture show batch capture dialog box.Refer to 4-6.Dv batch capture. Application setting show rsdvcap parameter setting dialog box. Refer to 4-3.Application settings. Cam setting s...

  • Page 37: 4-2.Control Bars

    33 4-2.Control bars 4-2-1.Camera and audio select bar: this bar has the camera list box and sound device list box as shown above. Camera list box displays a list of camera device connected to your pc. If this list box is blank, your camera isn’t recognized. “microsoft dv camera and vcr” string will ...

  • Page 38: 4-2-3.Video  Control Bar :

    34 4-2-3.Video control bar : you can control a dvcam from this control bar. The dvcam have a switch which selects video mode or camera mode. If you set this switch to camera mode or a dv tape is not inserted, this control bar will be disabled automatically. Set this switch to video mode to control t...

  • Page 39: 4-3.Application Settings

    35 4-3.Application settings when you select [application setting] of the [setting] menu, you will see the dialog box below. You can set up this application’s behavior..

  • Page 40

    36 category item description camera mode ccd mode select when you use a ccd camera. Dv mode select when you use a dvcam. Preview settings display timecode if checked, timecode will be displayed. Dv codec resolution capture settings capture with preview rename file name every capture execution you ca...

  • Page 41

    37 category item description dvcam settings check dvcam mode if you click here, this application will detect whether your dvcam is in camera mode or video mode automatically. If your dvcam is in video mode, the camera control bar will disappear. If your dvcam is in camera mode, the camera control ba...

  • Page 42

    38 c category item description when you control a dvcam from the pc consecutively, it takes some time for the dvcam to get ready for a next command from the pc. This time depends on the dvcam. If you have trouble in controlling the dvcam from the pc consecutively, change this value to a longer time ...

  • Page 43

    39 4-4.Capturing a video from a dvcam in camera mode when you want to capture a video image from a dvcam set to camera mode, follow steps through. 1. Confirm a dvcam is set to camera mode. Camera mode means you can capture a video image. If your dvcam is in video mode, change mode selection switch f...

  • Page 44

    40 4-5.Capturing a video from a dv tape 1. Set a dv tape in a dvcam and confirm the dvcam mode is set to video mode. Video mode means you can control a video of a dv tape. If your dvcam is in camera mode, change mode selection switch from camera mode to video mode slowly as mentioned 4-4.Capturing a...

  • Page 45: 4-6.Dv Batch Capture

    41 4-6.Dv batch capture batch capture function saves video images files as your time scheduling. To batch capture video images from a dv tape, follow steps through. 1.To show the batch capture window as shown right, select [batch capture list] of the [view] in the system menu. 2.Set a dv tape in a d...

  • Page 46

    42 9. The batch capture dialog box will be shown. Click [run] to start batch capture.This application searchs automatically the timecode you have just set and starts to capture video images and saves the file in the folder written in the “export directory” under the name of video + (number) starting...

  • Page 47

    43 4-7.Exporting a video data to a dvcam when you want to export an video data to a dvcam, follow steps through. 1. Set a dvcam to video mode. Video mode means you can control a video of a dv tape. If your dvcam is in camera mode, change mode selection switch from camera mode to video mode slowly as...

  • Page 48: 5. How to Use Rsdvstill

    44 5. How to use rsdvstill what is the rsdvstill? This application software has the following functions. •preview video data from a dvcam/a ccd camera. •save a still image to a bmp file. When rsdvstill starts with a dvcam connected to the cbfw3, rsdvstill will detect whether the dvcam is in camera m...

  • Page 49

    45 category description dv maker this list box shows a list of dvcam manufacturer such as sony, jvc, panasonic, canon, sharp, etc. Choose your dvcam manufacturer. If you can’t find it, choose other. Image size there are 3 kinds of resolution:720 x 480, 360 x 240, 88 x 60. This value means raw data f...

  • Page 50

    46 category description time code this box shows the timecode information of your dv tape. This timecode format is hour:minute:second:frame. When you click this button, you will see the screen below. You can select a folder where you want to save a bmp file. This button will be enabled only when you...

  • Page 51: 5-2.How to Save A Bmp File

    47 5-2.How to save a bmp file (1)save a bmp file from a dv tape 1.Set a dv tape in a dvcamand confirm the dvcam mode is set to video mode. Video mode means you can control a video of a dv tape. If the dvcam is in camera mode, change mode selection switch from camera mode to video mode slowly as ment...

  • Page 52

    48 (2)save a bmp file from a dvcam in camera mode or a ccd camera 1.Set a dvcamto camera mode. Camera mode means you can capture a video image. If your dvcam is in video mode, change mode selection switch from video mode to camera mode slowly as mentioned 4-4.Capturing a video from a dvcam in camera...

  • Page 53: 6. How to Use Compressavi

    49 6. How to use compressavi what is compressavi application software? This application software has the following functions. Convert microsoft dv-avi2 format video file to another format video file bi-directionally. As current existent video editing software don't support ms dv-avi2 format video fi...

  • Page 54

    50 3.Please specify an original video file and a converted video file name. Click [next]. (after conversion, an original video file remains in the hdd.) 6-1.How to convert the ms dv-avi2 format to other formats 1.When you start the compressavi, you will see the screen below. Click [execute]. 2.Pleas...

  • Page 55

    51 4.Please choose a conversion filter from the compression formats list box. Avi files made by rsdvcap have a ms dv-avi2 format. So, select the other compression formats than dv video encorder. There are many kinds of compression formats. (compression formats appeared in the [compression formats] l...

  • Page 56

    52 5.Click [next]. The file conversion starts. It takes much time to convert an avi file. Conversion time depends on the type of compression format. Please wait patiently. 6.When conversion ends, you will see the screen below. Click [finish]. You can now do a video editing with your video editting s...

  • Page 57

    53 6-2.How to convert other formats to the ms dv-avi2 format? You can export a video to a dvcam after you convert an existing avi file to the ms dv-avi2 format. 1.When you start the compressavi, you will see the screen below. Click [execute]. 2. Please select “convert other video file format to dv-a...

  • Page 58

    54 5.When conversion ends, you will see the screen below. Click [finish]. You can now export the converted data to a dvcam by using rsdvcap. 4.Click [next]. It may take much time to convert an avi file. Please wait patiently..

  • Page 59: 7. Setup For Macintosh

    Macintosh 55 7. Setup for macintosh to use the cbfw3 on macintosh, follow the steps below. 1.Install the cbfw3 driver. Refer to the chapter 7-1. 2.Insert the cbfw3. Refer to the chapter 7-2. 3.Connect a firewire device to the cbfw3. Refer to the chapter 7-3..

  • Page 60

    Macintosh 56 7-1.Cbfw3 driver installation before you insert the cbfw3 into the pc card slot, you have to install the cbfw3 driver. To install the cbfw3 driver, follow the steps. 1.Close all programs currently running on your computer. 2.Insert the cbfw3 cd-rom into the cd-rom drive. 3.The following...

  • Page 61

    Macintosh 57 6.The following window will show up. Click [install]. 7.The following window will show up. Click [restart] to restart your mac. 8.Open [extensions] folder in the [system folder]. If you can find the rex-cbfw enabler, the cbfw3 driver was installed correctly..

  • Page 62: 7-2.Inserting The Cbfw3

    Macintosh 58 7-2.Inserting the cbfw3 1.Insert the cbfw3 into the pc card slot as shown below. Refer to the manual that accompanied with your mac for the location of the pc card slot. Note you may not be able to insert another pc card with the cbfw3 simultaneously. You may not be able to insert the c...

  • Page 63

    Macintosh 59 7-3.Connecting a firewire device to the cbfw3 follow the steps to connect a 1394 hard disk drive(hdd). 1.Insert the cbfw3 into the pc card slot. 2.Connect the optional ac adapter(sold separately) to the cbfw3 only when you connect a firewire device which needs cable power such as a hdd,...

  • Page 64: 8. Troubleshooting

    60 2. If you use windows 98 se or windows 2000,there have to be a [microsoft dv camera and vcr] string under the “imaging device” in the device manager. If you can not find it, make sure your dvcam is powered on. If you use windows me, there have to be a camera name string under the “imaging device”...

  • Page 65

    61 8-2.When you can not export smooth and clear video image to a dvcam(windows 98se/me) if you use windows 2000, see 8-3.When you can not export smooth and clear video image to a dvcam(windows 2000). In the cbfw3 cd-rom, there is the driver for cardbus bridge property setting controller named cbrpse...

  • Page 66: Cardbus Bridges Name List

    62 cardbus bridges name list cardbus bridge chip made by ricoh: -ricoh rl5c476 cardbus controller -ricoh rl/rb5c478 cardbus controller -ricoh rl5c475 cardbus controller cardbus bridge chip made by texas instruments(ti): -texas instruments pci-1210 cardbus controller -texas instruments pci-1211 cardb...

  • Page 67

    63 2. Restrictions. If you come across the following cardbus bridge chip, unfortunately you can not use the cbfw3. -ricoh rl5c465 cardbus controller -ricoh rl5c466 cardbus controller -cirrus logic pd6832 cardbus controller if you come across ricoh cardbus bridge rl5c476, please note the following re...

  • Page 68

    64 3.How to install the driver:cbprset.Sys or merpset.Sys you have already installed the driver [texas instruments ohci compliant ieee 1394 host controller]. You should replace it to the new “ratoc 1394 cardbus card(ti os version)” driver. You can replace it, simply following the instructins: 1.Inse...

  • Page 69

    65 you will see the screen below when you use windows me. Select [specify the location of the driver(advanced)] and click [next]. 7.Click the driver tab and click [update driver...]. 8.You will see the screen below if you use windows 98se. Click [next]..

  • Page 70

    66 9.You will see the screen below when you use windows 98 se. Select [display a list of all drivers in a specific location,so you can select the driver you want] and click [next]. You will see the screen below when you use windows me. Select [display a list of all drivers in a specific location,so ...

  • Page 71

    67 13.You will see the screen below. Click [next]. 11.You will see the screen below. Set the cbfw3 cd-rom in the cd-rom drive and type “d\win98se” or “d\winme”, where “d” means the cd-rom drive. When you use windows 98 se, type “d\win98se”. When you use windowsme, type “d\winme”. After that, click [...

  • Page 72

    68 15.When a dialog box says [the file cbrpset.Vxd on ratoc fw install cd can not be found. Insert ratoc fw install cd in the selected drive,and click ok.], type “d:\win98se” and click [ok]. This message may appears only when your windows is windows 98se. 14.If the following message appears,make sur...

  • Page 73

    69 18.Make sure you can find a [ratoc 1394 cardbus card(ti os version)] string in the device manager. If there is yellow “!” mark on a [ratoc 1394 cardbus card(ti os version)] string, restart your laptop pc again. 16.You will see the screen below. Click [finish]. 17.You will see the screen below. Cl...

  • Page 74

    70 8-3.When you can not export smooth and clear video image to a dvcam(windows 2000) if you use windows 98 se/windows me, see 8-2.When you can not export smooth and clear video image to a dvcam(windows 98se/me).In the cbfw3 cd-rom, there is the driver for cardbus bridge property setting controller n...

  • Page 75: Cardbus Bridges Name List

    71 cardbus bridges name list cardbus bridge chip made by ricoh: -ricoh rl5c476 cardbus controller -ricoh rl/rb5c478 cardbus controller -ricoh rl5c475 cardbus controller cardbus bridge chip made by texas instruments(ti): -texas instruments pci-1210 cardbus controller -texas instruments pci-1211 cardb...

  • Page 76

    72 2. Restrictions. If you come across the following cardbus bridge chip, unfortunately you can not use the cbfw3. -ricoh rl5c465 cardbus controller -ricoh rl5c466 cardbus controller -cirrus logic pd6832 cardbus controller if you come across ricoh cardbus bridge rl5c476, please note the following re...

  • Page 77

    73 3.How to install the driver:cbprset.Sys you have already installed the driver [texas instruments ohci compliant ieee 1394 host controller]. You should replace it to the new “ratoc 1394 cardbus card(ti os version)” driver. You can update and replace it, simply following the instructions below. 1.I...

  • Page 78

    74 7.You will see the screen below. Click the driver tab and click [update driver...]. 8.You will see the screen below. Click [next]..

  • Page 79

    75 11.You will see the screen below. Insert the cbfw3 cd-rom and type “d:\win2000”, where d means your cd-rom drive and click [ok]. 9.You will see the screen below. Check [search for a suitable driver for my device (recommended)] and click [next]. 10.You will see the screen below. Check [specify a l...

  • Page 80

    76 12.You will see the screen below. Click [next]. 13.You will see the screen below. Click [finish]..

  • Page 81

    77 you have now completed the installation of the driver. Please try dv export function with rsdvcap.Exe. 16.Make sure there is a [ratoc 1394 cardbus card (ti win2k version)] string in the device manager. I if there is yellow “!” mark on [ratoc 1394 cardbus card (ti win2k version)], restart your pc ...

  • Page 82

    78 8-4. A captured file is choppy or jerky i the data rate from a dvcam is 3.6mb/sec. If your hdd sustainted data write rate is lower than 3.6mb/sec., a captured file may get choppy or jerky when you play back the file. To avoid this trouble, enable dma function of your hdd, following the steps. 1.O...

  • Page 83

    79 8-5.Using the format utility named frfmtw9x.Exe you can format a 1394 storage device such as a hdd, zip, mo with format utility named frfmtw9x.Exe. This utility is included in the cbfw3 cd-rom. This frfmtw9x.Exe runs only on windows 98se, windows me. If you want to format a 1394 storage device on...

  • Page 84

    80 6.You will see the screen below. Select [initialize/format media] from the [edit] menu. 7.You will see the initialize/format screen below. Select format type. If you want to do low level format simultaneously, check [low level format]. Then, click [ok]. (caution) you can do low level format only ...

  • Page 85

    81 8.If you selected ibm-pc/at fdisk format at step 7), the message box saying [you should create partition next] appears. Then, click [ok]. You will see the screen shown in the step 6) and select [create partition] from the [edit] menu. After that, you will see the screen below. Select [file system...

  • Page 86

    82 8-6.Formatting media on windows 2000 when you want to format a 1394 storage device such as a hdd, zip, mo on windows 2000, you can use [computer management]. Here is a brief explanation: 1.Open [my computer] and double click [control panel]. 2.Double click [administrative tools] and start [comput...

  • Page 87: 9-1. How to Register

    83 9. Registration and tech-support 9-1. How to register we highly recommend to register yourself as our customer through our on-line registration. 1. On the internet, access our site (http://www.Ratocsystems.Com/english/) 2. Follow window menu guide to register. 3. Fill out and submit the registrat...

  • Page 88: 10. Options

    84 10. Options options are available (sold separately) at the web site: 1. Http://www.Ratocsystems.Com/english/ 2. Http://www.Firewireshop.Com -cbfw-466 (4pin-6pin ieee1394(firewire) cable(6 feet)) -cbfw-666 (6pin-6pin ieee1394(firewire) cable(6 feet)) -cbfw-463 (4pin-6pin ieee1394(firewire) cable(3...

  • Page 89: 11. Specifications

    85 11. Specifications product name :cbfw3 ieee1394 cardbus pc card transfer :pc card standard(cardbus) 32bit bus master data transfer rate :100/200/400mbps power requirements : voltage :+3.3v(supplied from pc card slot) current :110ma (idle) 220ma (max) operating environment : temperature : 0°c(32°f...

  • Page 90: Appendix

    86 appendix trademarks -windows is a registered trademark of microsoft corporation. -sony corporation has a original copyright of sonydvcr.Sys. - other brand and product names may be registered trademarks or trademarks of their respective holders. I)fcc statement this equipment has been tested and f...