Pciu2 user’s manual june 2001 rev.1.0 usb2.0 pci host board.
2 contents 1. Introduction........................................................................... 3 1-1. Features ....................................................................................................... 3 1-2. Restrictions .............................................................
3 •supports 480mbps(high-speed), 12mbps(full-speed), 1.5mbps(low-speed) data transfer mode. This usb2.0 host adapter is fully backwards compatible with the currrent usb1.1 devices. •certified and passed usb hi-speed compliance test. •includes our original usb2.0 ehci driver. Supports windows 98se, w...
4 2. Before installing... 2-1. Package check the package contents: •pciu2 pci board •low profile bracket •software cd-rom •user’s manual note if any of these items are missing from the pciu2 retail package, contact your supplier immediately. 2-2. Using low-profile bracket if you use the pciu2 with a...
5 after installing it, start your pc. Then, you need to install the driver for the pciu2. A)when you use windows 98se----------- proceed to chapter 3-2. B)when you use windows 2000------------proceed to chapter 3-3. C)when you use windows me--------------proceed to chapter 3-4. Turn off your compute...
6 3-2. Installing the driver(windows 98se) when you use windows 98se, follow the steps to install the driver. 1. When you start your pc after installing the pciu2, the following hardware wizard will appear. Insert the pciu2 cd-rom into the cd-rom drive and click [next]. 2. Select [search for the bes...
7 4. Select [the updated driver(recommended) nec usb open host controller] and click [next]. 5. Click [next]. 6. Click [finish]. 7. The same hardware wizard as shown at the step 1 through 6 will appear again. Follow the same procedure..
8 10. Select [specify a location] and type in [d:\pciu2] and click [next]. (d means your cd-rom drive letter. If your cd-rom is “e”, you have to type in [e:\pciu2].) 8. Then, the following hardware wizard will appear. 9. Select [search for the best driver for your device.(recommended)] and click [ne...
9 11. Make sure windows found the pciehci.Inf file in the pciu2 folder in the cd-rom drive. Then, click [next]. 12. Click [finish]. 13. Restart your pc. You have now finished installing the driver..
10 14. To verify that the driver is installed correctly, right-click on [my computer], select [system properties], and then select the [device manager] tab. If you can find two [nec usb open host controller] strings and a [ratoc pci usb enhanced host controller] string under the [universal serial bu...
11 3-3. Installing the driver(windows 2000) before you install the driver, make sure windows 2000 service pack2 or later is already installed . To verify service pack2 or later is installed, right-click on [my computer], and then select [system properties].If you can find a “service pack” string as ...
12 3. Select [specify a location] and click [next]. 4. The following dialog box will appear.Type in [e:\pciu2] and click [ok]. (e means your cd-rom drive letter. If your cd-rom is “d”, you have to type in [d:\pciu2].) 5. Make sure windows found the pciehci.Inf file in the pciu2 folder in the cd-rom ...
13 8. To verify that the driver is installed correctly, right-click on [my computer], select [system properties], and then select the [hardware] tab. Then, click the [device manager] button. If you can find two [nec pci to usb open host controller] strings and a [ratoc pci usb enhanced host controll...
14 2. Select [ratoc pci usb enhanced host controller] and click [ok]. 3-4. Installing the driver(windows me) when you use windows me, follow the steps to install the driver. 1. When you start your pc after installing the pciu2, the following hardware wizard will appear. Insert the pciu2 cd-rom into ...
15 note you may find the [ratoc pci usb enhanced host controller] string with green ? Marks. But this doesn’t affect the peformance of this pciu2 board. 5. To verify that the driver is installed correctly, right-click on [my computer], select [system properties], and then select the [device manager]...
16 4-1. How to register we highly recommend to register yourself as our customer through our on-line registration. 1. On the internet, access our site (http://www.Ratocsystems.Com/english/) 2. Follow window menu guide to register. 3. Fill out and submit the registration form. 4-2. Software update an...
17 option is available (sold separately) at the web site: 1. Http://www.Ratocsystems.Com/english/ 2. Http://www.Firewireshop.Com -usb2-01 (usb2.0 cable(3 feet)) if you have any questions about the option, contact to: ratoc systems insternational, inc. Tech support tel : (408)955-9400 fax: (408)955-9...
18 model name board type pci bus transfer usb data transfer rate e n v i r o n m e n t usb connector usb port corrent optional connector usb 2.0 type a x 2port 500ma at each port(max.) j4 connector to be used for an optional front bay 6. Specifications pciu2 usb2.0 pci host board 32bitpci bus master...
19 copyright ©2001 ratoc systems,inc. All rights reserved. No part of this publication may be reproduced, store in a retrieval system, or transmitted in any form or by any means(electronic, mechanical, photocopying, recording or otherwise) without the prior written consent of ratoc systems,inc. Trad...
