Raven MPV-7100 Owners And Operation Manual

Manual is about: MULTI-PURPOSE VEHICLE

Summary of MPV-7100

  • Page 1

    Multi-purpose vehicle owner’s and operation manual mpv -7100/7100s d100100 r1:01:14.

  • Page 3

    C ong rat ulat i ons on t h e purc h ase of y our new raven mpv ( mult i - purpose veh i c le) ! This advanced new product is unlike anything you've ever used, so please read this instruction manual carefully before first use. The mpv is designed to help you accomplish a variety of tasks, from mowin...

  • Page 5

    Www. Ravenameri c a. C om c ontents introduction ................................................................................................................................................................ 6 customer responsibilities .................................................................

  • Page 6

    Locating the serial number label (snl) raven mpv-7100/7100s owner’s manual the raven multi-purpose vehicle (mpv) was carefully designed and assembled in the usa to provide the best performance when properly operated and maintained. This advanced new product is designed to help you accomplish a varie...

  • Page 7: Warning!

    Www. Ravenameri c a. C om i ntroduction death or serious injury will occur if instructions are not followed. Warning! Serious injury or even death can occur if instructions are not followed. Caution! Injury can occur if instructions are not followed. Important damage to the mpv or other property cou...

  • Page 8

    Install the steering wheel a. Locate the steering wheel and steering wheel hardware packet. B. Ensure that the front wheels are pointing forward and slide steering wheel onto the steering spindle, making sure that the steering wheel spoke between the hub connectors is centered and pointing towards t...

  • Page 9

    Install the 30 a fuse a. Locate the green 30 a fuses in the bag containing the mpv keys inside the instruction manual bag. B. Lift the seat. C. Locate the fuse connections under the black plate. D. Open the fuse holder. E. Insert the fuses. F. Close the fuse holder. G. Lower the seat back into place...

  • Page 10: Warning!

    Check the oil a. Remove the dipstick and wipe with a cloth. B. Insert and press the dipstick all the way into the tube. C. Remove the dipstick and visually check the oil level on the dipstick gauge. D. Keep the oil level between the hi and lo levels on the dipstick. E. Firmly press the dipstick into...

  • Page 11

    1 12 12 11 14 17 22 23 24 25 26 27 18 20 21 2 3 4 5 6 7 8 9 10 19 28 15 13 11 16 www. Ravenameri c a. C om 1 drive mode switch 2 cruise control switch 3 ignition 4 reverse mow override switch 5 blade engage switch 6 steering wheel 7 hood 8 fuel tank with sta-bil ® pouches (under hood) 9 headlights 1...

  • Page 12: Warning!

    Ignition switch operation a. Stop - disables all functions of the mpv. Must be in this position to avoid battery drainage when not in use. Battery will be depleted if left in electric mode position. B. Electric mode - drive in forward and reverse. C. Hybrid mode - (gas and electric) - mow, tow and d...

  • Page 13: Cruise Off

    Cruise control operation disengaging the cruise control a. Push the brake pedal or push the cruise control button. B. Cruise control will no longer be activated. Setting the cruise control a. Push the throttle down until you accelerate to the desired speed. B. Hold the throttle at that speed and pus...

  • Page 14

    Gauges, lights and switches fuel gauge the fuel gauge indicates the current level of fuel in the gas tank. Led light indicator cluster indicates low battery (in low gear, electric mode only), power on, and the parking brake status. Headlight switch press the headlight symbol on the switch to turn th...

  • Page 15: Warning!

    Deck power connector blade engage switch pull up to engage the blades. Press down to stop the blades. Deck height operation pull back to raise the deck. Push forward to lower the deck. D eck h eight 5 432 1 h i l o www. Ravenameri c a. C om cutting deck features reverse mow override (rmo) the revers...

  • Page 16: Warning!

    Service hatch pull back on the service latches, then rotate the hatch down to open. Opening the hood squeeze the latch and lift the hood to open. Squeeze and hold the latch, then press down on the hood to close. The customer service phone number and web address of on-line videos are located on the u...

  • Page 17: Warning!

    Seat adjustment while seated, pull up on the seat adjustment lever and slide the seat forward or backward to adjust the position. Removing the tailgate a. Lower the tailgate all the way down. B. Press down on the tailgate at the hinge points to remove. C. Reverse these steps for reassembly. Gear sel...

  • Page 18: Warning!

    Generator panel raven mpv-7100/7100s owner’s manual the safety interlock system the safety interlock system is a system of sensors that will stop your mpv and/or disengage your blades if the operator leaves the seat or other hazardous situations arise. This system includes the operator presence swit...

  • Page 19: Warning!

    Operating on electric only mode a. Select high or low gear. (see page 17). B. Set the drive mode switch to neutral. C. Turn the key in the ignition switch to the position labeled with the battery icon until it clicks one time. D. Step on the brake pedal to release the parking brake. The mpv will now...

  • Page 20: Warning!

    Raven mpv-7100/7100s owner’s manual towing and using mpv attachments t o w i n g sa f e t y your mpv has a towing capacity of 550 lbs. Tow only trailers or attachments with a standard towing hitch. Do not attach equipment except at the hitch point. Warning! Use extreme caution when hauling or towing...

  • Page 21

    Adjusting the cutting height a. Pull the deck lift lever towards you out of the height slot. B. The numbers indicated on the lever are for reference only (1 - low, 5 - high). C. Push the lever forward to lower the deck. D. Pull back to raise the deck. E. Push the lever into the height slot to lock t...

  • Page 22

    Engaging reverse mow override (rmo): a. Start the engine, then check the area behind and below your mpv to make sure it is clear of adults, children, pets or other objects. B. Engage the blades, then press the rmo switch. C. Put the drive mode switch into the reverse position. D. Once activated, the...

  • Page 23

    Slope sighting www. Ravenameri c a. C om o peration 2 3.

  • Page 24: Warning!

    Raven mpv-7100/7100s owner’s manual generate mode safety information exhaust contains high levels of carbon monoxide (co), a poisonous gas you cannot see or smell. If you can smell the generator exhaust, you are breathing co. But even if you cannot smell the exhaust, you could be breathing co. Even ...

  • Page 25: Caution!

    Www. Ravenameri c a. C om using the generator caution! • for outdoor use only. Only use the mpv generator outdoors and far away from open windows, doors, and vents. These openings can pull in generator exhaust. • do not allow children or untrained individuals to use this unit. • keep all bystanders,...

  • Page 26: Important

    Plugging a device in to the ac receptacles a. Engage the parking brake and start the mpv without devices connected. B. Allow the engine to run for several minutes after it has been started. C. Confirm that the electrical device is switched off, then plug it into the unit. D. Switch the generator mod...

  • Page 27: Caution!

    Plugging a device to the dc receptacle plug the electrical device power cord into the 12v dc outlet and ensure the power cord is securely in place. Use the device as instructed. Remove after use by pulling the power cord out of the receptacle. Www. Ravenameri c a. C om load connection method the loa...

  • Page 28

    Power management to prolong the life of the mpv generator and attached devices, it is important to take care when adding electrical loads to the generator. There should be nothing connected to the generator outlets before starting the mpv engine. The correct and safe way to manage generator power is...

  • Page 29: Important

    Www. Ravenameri c a. C om ansi /ul 2 2 01 mpv g e n e r a t o r sp e c i t e m ra t i n g t o l e r a n c e voltage 120 (rated) -5% frequency 60hz (rated) -5% phases single phase amperes 54a -10% volt-amperes 6500va -10% watts 6500w -10% power factor 1.0 -10% watts and volt-amperes 6.5kw/6500va rpm ...

  • Page 30

    Removing the cutting deck a. Ensure the mpv is turned off with the key removed. B. Lower the cutting deck completely to the ground using the deck lift lever. C. Disconnect the deck power plug. D. Disconnect the front pin, then disconnect the two rear pins. E. Raise the deck lever to the highest posi...

  • Page 31

    Attaching the cutting deck a. Ensure the mpv is turned off with the key removed. B. Check that the deck lift lever is in the lowest position, then slide the deck under the mpv. C. Place the deck lift lever into the lowest setting. D. Align and connect the front and rear pins. E. Connect the deck pow...

  • Page 32

    Side to side adjustment a. Ensure the mpv is turned off with the key removed, and that the deck is unplugged (see page 30 step c). B. Raise the cutting deck to the highest position. C. Measure the distance from the outside edges of the deck to the ground. If they are equal, the deck is level. D. If ...

  • Page 33

    Front to rear (lock nut) adjustment a. Ensure the mpv is turned off with the key removed, and that the deck is unplugged (see page 30 step c). B. Remove the pin from the deck front link rod. C. Loosen the lock nut using a 16mm wrench. D. Tighten or loosen the rod end to adjust. E. Measure and adjust...

  • Page 34: Warning!

    Removing the blades a. Ensure the mpv is turned off with the key removed, and that the deck is unplugged (see page 30 step c). B. Remove the cutting deck. See remove the cutting deck section on page 30. C. Turn the deck over, this requires two people. D. Use a 17mm socket wrench to remove the lock n...

  • Page 35

    Hi lo changing the oil a. Start the engine and allow it to run briefly to warm the oil in the mpv, then turn the engine off, remove the key and engage the parking brake. B. Pull back on the service hatch latches and rotate the service hatch down to open. C. Place an appropriate oil collection contai...

  • Page 36

    Check the oil a. Turn the engine off and allow the engine to cool. B. Open the service hatch. C. Remove the dipstick from the tube and wipe off any oil, then insert and press the dipstick all the way into the oil fill tube. D. Remove the dipstick and visually check the oil level on the dipstick gaug...

  • Page 37

    Changing the spark plug a. Ensure the engine is cool before changing the spark plug. B. Open the service hatch. C. Remove spark plug cap to reveal the spark plug. D. Remove the spark plug using a 13/16” spark plug torque wrench (not included). E. Place the new spark plug into the socket and rotate u...

  • Page 38

    Changing the air filter a. Turn the engine off and allow it to cool. B. Open the service hatch. C. Release the latches on the black air filter cover, then remove the metal filter cover. D. Replace the air filter, positioning the flat side toward the engine and ensure the plastic filter cover is on t...

  • Page 39: Warning!

    Front to rear adjustment a. The brake adjustment is located on top of the rear axle on the inboard side of each wheel. B. Tighten or loosen each adjuster equally by adjusting one and then the other to ensure even wear. Use a 14mm wrench to turn clockwise to tighten, and counterclockwise to loosen. C...

  • Page 40

    Removing the battery and cleaning the 12 volt battery terminals a. Remove the 5 bolts from the right side panel using an 8mm wrench, then remove the panel. B. Use an 8mm wrench (not included) to remove the two bolts securing metal bracket around the battery, then remove the bracket. C. Use an insula...

  • Page 41: Caution!

    Charging the 12 volt battery a. Use the 12 volt charger included with your mpv to charge the 12 volt battery. B. Connect the 12 volt charger to the 12 volt receptacle on the generator panel. C. Connect the charger to a power source. D. Allow the unit to charge for 14 ̶ 16 hours. Www. Ravenameri c a....

  • Page 42

    Replacing a fuse a. Lift the seat b. Locate the fuse connections under the black plate. C. Open the fuse holder cover of the fuse needing replacement. D. Replace the blown fuse. E. Close the fuse holder cover. F. Lower the seat back into place. Raven mpv-7100/7100s owner’s manual s ervice & m ainten...

  • Page 43: Caution!

    Www. Ravenameri c a. C om s ervice & m aintenance cleaning to maximize the longevity and appearance of your mpv, it is best to keep the unit stored in a covered, well ventilated area if possible. Clean and wax the painted metal parts periodically, using a high quality non-abrasive automotive wax. Th...

  • Page 44

    Raven mpv-7100/7100s owner’s manual prob lem c ause solut i on engine runs erratically fuel line blocked. Clean fuel line/filter. Dirty or old fuel. Drain tank. Refill with fresh, clean gasoline. Dirty air filter. Clean/replace air filter. Spark plug wire loose. Check and connect wire. Engine overhe...

  • Page 45

    Www. Ravenameri c a. C om prob lem c ause solut i on mpv will not move generate mode is set to on. Set generate mode to off. Parking brake engaged. Disengage parking brake. Important information about the generator note: the generator is equipped with five (5) circuit breakers. One each for the 20a,...

  • Page 46

    Raven mpv-7100/7100s owner’s manual important information about system fuses warning! This system is equipped with several fuses that protect the electrical system and components from severe damage in the event of a system failure. Please note that if any of the following occur do not attempt to ser...

  • Page 47

    Www. Ravenameri c a. C om t ec h ni c al i nf ormat i on model number: mpv-7100 engine displacement 420cc engine manufacturer rato engine type ohv extended life gasoline capacity: 5 gal/19 ltr gasoline type: unleaded front tires: 18 x 8.5-8 4-ply rear tires: 20 x 8-10 4-ply inflate front tires to 12...

  • Page 48

    Raven mpv-7100/7100s owner’s manual part s and ac c essori es/servi c e i t ems mpv re p l a c e m e n t pa r t s part name component description part number mpv blade set mpv replacement blades – qty 2 bl46 mpv blade bolt & adapter kit blade adapter, bolt, flat washer & lock washer bl46a universal ...

  • Page 49

    Www. Ravenameri c a. C om w arranty & r egistration 6 exclusions: this warranty does not cover: normal wear; contaminants in the fuel or oil; damage as a result of use in a manner for which the product was not designed; damage caused by modification or use of unsuitable attachments or accessories, o...

  • Page 50

    Raven mpv-7100/7100s owner’s manual 5 0

  • Page 51

    Www. Ravenameri c a. C om 5 1.

  • Page 52: I Mport Ant

    The mpv is not an atv. Avoid driving through water. Never interact with the generator if it is wet. Store the mpv in a covered, well-ventilated area at all times. I mport ant.