Rayburn 200S User Instructions - Cookmaster 200S and Rayburn

Summary of 200S

  • Page 1

    This information refers to the following products rayburn cookers model 200s model 212s please note that some original pages may not appear in original numerical order, but have been rearranged for clarity or deleted if not appropriate. Warning this information is a copy of an original archive, ther...

  • Page 2: Cookmaster 200S and Rayburn

    The user should obtain confirmation from the installer that the chimney is of sound airtight construction, is clear of obstructions and has been swept before installation. The rayburn cookmaster 200s has been designed to burn a variety of solid fuels and thereby provide heating facilities for cookin...

  • Page 3

    Oven door operation - see fig. 1 to open the doors. Twist the handle slightly to lift up the door catch from the locking spindle and pull the door open. To close the doors. Gently push the door shut until the door catch makes contact with the locking spindle. Fire door operation - see fig. 2 to open...

  • Page 4

    1. Check the flue pipe is free of blockage. 2. Open firebox door. 3. Open ashpit door. 4. Remove ashpan. 5. De-ash (fig. 3) also see page 3 de-ashing and remove any dead fuel from bottomgrate as described under ‘ removal of clinker and bottomgrate ’. 6. Replace ashpan. 7. Open flue chamber to maximu...

  • Page 5

    Control setting set spinwheel open which does not require to be open more than: 1. Coke - five complete turns. 2. Other recommended fuels - three complete turns during cooking period. Set the flue chamber damper fully open after refuelling and reset to position which has been found by practical expe...

  • Page 6

    The best results can only be obtained by using machined base utensils. The hottest part of the hotplate is immediately above the fire, the other end being for simmering. The circular plug in the hotplate (near the flue chamber end) is for flue cleaning and must not be removed for cooking. Note: to o...

  • Page 7

    Both insulating covers should be raised and allowed to cool before cleaning with a soapy, damp cloth. Use a wire brush to keep the cast iron hotplate clean. General cleaning is best carried out when the rayburn is cool. Important note: aga recommend vitreous enamel association approved cleaners for ...

  • Page 8

    The oven is indirectly heated from outside by hot gases from the heat source so no flames or elements within the ovens means full use can be made of the whole cooking space. The main oven is slightly hotter towards the top than the bottom. At a low idling heat the main oven can be used for long slow...

  • Page 9

    8 for further advice or information contact your local distributor/stockist with aga’s policy of continuous product improvement, the company reserves the right to change specifications and make modifications to the appliance described at any time. Manufactured by aga station road ketley telford shro...

  • Page 10

    The rayburn cookmaster 200s is intended to supply heating for cooking.The rayburn cookmaster plus 212s is intended to supply heating for cooking and domestic hot water. The cooker fully meets the requirements of bs: 1252 and is fully approved by the hetas ltd approval scheme. Air for combustion with...

  • Page 11

    The 28mm minimum diameter primary flow and return pipes must not exceed 10m in length and pipes longer than 5m must be lagged. Ensure that the flow pipe has an open vent and rises continuously from the boiler to the cylinder to ensure good gravity circulation. The water draw-off pipes to the taps mu...

  • Page 12

    Checking existing chimney the internal and external location of the chimney should be checked before the appliance is installed and rectification made where necessary to prevent leakage or porosity. The soundness of the chimney which should have a minimum flue dimension of 150mm can be confirmed by ...

  • Page 13

    The position of available types of flue layouts are shown in figs. 2, 3 and 4, the cooker flue chamber is adaptable to providing either top or back flue outlets, by means of the reversible loose socket. A) rear flue outlet this must only be used where there is a brick flue immediately behind the coo...

  • Page 14

    Place the cooker in the intended position and lift out the surface ground hotplate, checking that the joint between the underside of the hob and the top of the cooker are intact. Any joints which have opened should be made good with fire cement provided. Replace the hotplate making sure that it is s...

  • Page 15

    After completing the installation, the heating contractor should demonstrate to the user, the operation of the appliance and the routine flue operating method. (i) check that the system is full of water and free from air pockets. (rayburn cookmaster plus 212s only). (ii) when lighting pull the flue ...

  • Page 16

    7.

  • Page 17

    8 for further advice or information contact your local distributor/stockist with aga’s policy of continuous product improvement, the company reserves the right to change specifications and make modifications to the appliance described at any time. Manufactured by aga station road ketley telford shro...