D7679-1 contents introduction this handbook explains how to install, connect, operate and maintain your seatalk 2 keyboard (e55061). This keyboard is also supplied with the remote station kit (t82005) - details of how to integrate these devices is given on page 6. Intended use this keyboard is inten...
Active wpts mob data menu cancel ok 9 wxyz 8 tuv 7 pqrs . 4 ghi 5 jkl 2 abc 3 def 1 6 mno range page 0 out in wpts mob to manage waypoints and initiate mob. Menu to access set up menus and help information. Page to change page and configure page sets. Active to select the active window. Soft keys pr...
Warning: navigation aid although this product has been designed to be accurate and reliable, many factors can affect its performance. As a result, it should only be used as an aid to navigation and should never replace common sense and navigational judgement. Always maintain a permanent watch so you...
Planning the installation where can the seatalk 2 keyboard be mounted? The seatalk 2 keyboard can be flush or trunnion mounted either indoors or outdoors. It is waterproof to cfr-46 standard. Important: the drain tube is not required if the keyboard is mounted indoors or in an area protected from ra...
Configuration 2 cable length between e-series display and keyboard exceeds 4.5m and not linking into an existing seatalk 2 system. Configuration 3 integrating the keyboard into an existing seatalk 2 system. E-series display seatalk 2 keyboard junction box additional junction box e series display ter...
Seatalk 2 keyboard alarm alarm red black red black vga out cable, 5m not waterproof m1500 monitor junction box not supplied/accessory/existing system station 1 station 2 no other seatalk devices connected other seatalk devices connected seatalk 2 cable (1.5 m) keyboard cable (attached/3 m) remote st...
How do i install the keyboard? 1. Using self-adhesive or masking tape, fix the template in the required position. Note: ensure that there are no cables or other parts that will be damaged, when the panel is drilled and sawn. 2. Drill a pilot hole inside the shaded area of the template. 3. Saw around...
5. Peel the backing from the gasket and stick it to the underside of the cradle. 7. If mounting the keyboard in an area unprotected from rain and/or sea spray, fit the drain tube and ensure that it runs to a suitable exit point below the level of the keyboard and the studs. 8. Fit the keyboard assem...
What spares are available? ... Description part no. Cradle assembly (includes cradle, cable, drain tube, gasket and latch) r58213 flush mount kit (includes gasket, clamps, drain tube, studs and thumb nuts) r58211 latch r89043 suncover r58212 what accessories are available? ... Description part no. S...
Removing/refitting what routine checks and servicing can i do? ... On a regular basis, examine all cables for signs of damage, such as chafing, cuts or nicks and check that all cables are securely connected. The seatalk 2 keyboard has no user serviceable parts. How should i clean my keyboard? ... Re...
Important information 11 d7707-1 emc conformance all raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment. The design and manufacture of raymarine equipment and accessories conforms to the appropriate electromagnetic compatibi...
Raymarine uk limited quay point, northarbour road, portsmouth, hampshire england po6 3td tel: + 44 (0)23 9269 3611 fax: + 44 (0)23 9269 4642 www.Raymarine.Com raymarine incorporated 21 manchester street merrimack, nh03054 - 4801 usa tel: 603-881-5200 fax: 603-864-4756 www.Raymarine.Com document no: ...
Configuration 4 cable length between e-series display and k eyboard less than 4.5m and linking into an existing combined seat alk/seat alk 2 system with st290 dpu . Do not connect the st290 to the e-series seat alk 2 connection. Seatalk 2 keyboard junction box e series display terminator terminator ...
