Eci-100 engine & contr o l interf ace installation instructions english date: 12-2013 document number: 87202-2-en © 2013 raymarine uk limited eci–100
Trademark and patents notice autohelm, hsb 2 , raytech navigator, sail pilot, seatalk, seatalk ng , seatalk hs and sportpilot are registered trademarks of raymarine uk limited. Raytalk, seahawk, smartpilot, pathfinder and raymarine are registered trademarks of raymarine holdings limited. Flir is a r...
Contents chapter 1 important information certified installation water ingress disclaimer emc installation guidelines suppression ferrites connections to other equipment declaration of conformity product disposal warranty registration imo and solas technical accuracy chapter 2 document and product in...
Chapter 1: important information certified installation raymarine recommends certified installation by a raymarine approved installer. A certified installation qualifies for enhanced product warranty benefits. Contact your raymarine dealer for further details, and refer to the separate warranty docu...
Product disposal dispose of this product in accordance with the weee directive. The waste electrical and electronic equipment (weee directive requires the recycling of waste electrical and electronic equipment. Whilst the weee directive does not apply to some raymarine products, we support its polic...
Chapter 2: document and product information chapter contents • 2.1 document information • 2.2 product overview document and product information.
2.1 document information this document contains important information related to the installation of your raymarine product. The document includes information to help you: • plan your installation and ensure you have all the necessary equipment; • install and connect your product as part of a wider ...
Chapter 3: planning the installation chapter contents • 3.1 installation checklist • 3.2 parts supplied • 3.3 required additional components • 3.4 compatible multifunction displays • 3.5 compatible autopilot systems • 3.6 software updates • 3.7 tools required • 3.8 typical systems • 3.9 warnings and...
3.1 installation checklist installation includes the following activities: installation task 1 plan your system. 2 obtain all required equipment and tools. 3 site all equipment. 4 route all cables. 5 drill cable and mounting holes. 6 make all connections into equipment. 7 secure all equipment in pla...
3.3 required additional components this product forms part of a system of electronics and requires the following additional components for full operation. • engine specific adaptor cables are required to connect your unit to the engine(s) can bus. Refer to chapter 10 spares and accessories for suita...
3.5 compatible autopilot systems for steering control this product is compatible with the following raymarine autopilots. • ev2 — evolution tm autopilot 3.6 software updates the software running on the product can be updated. • raymarine periodically releases software updates to improve product perf...
3.7 tools required product installation requires the following tools: item description quantity power drill 1 pozidrive screwdriver 1 drill bit of appropriate size* 1 note: * the appropriate drill bit size is dependent on the thickness and material of the mounting surface. 3.8 typical systems import...
Item description 1 multifunction display 2 vessel engines (connection to engine’s can bus) 3 engine specific adaptor cables 4 eci units 5 seatalk ng 5–way block example: expanded system in the example below the unit is used as both engine interface and steering control interface simultaneously. Stby...
3.10 general location requirements important considerations when choosing a suitable location for your product. This product is suitable for mounting below decks. The product should be mounted where it will be: • protected from physical damage and excessive vibration. • well ventilated and away from...
Chapter 4: cables and connections chapter contents • 4.1 general cabling guidance • 4.2 connections overview • 4.3 power connection • 4.4 data and control connections cables and connections.
4.1 general cabling guidance cable types and length it is important to use cables of the appropriate type and length • unless otherwise stated use only standard cables of the correct type, supplied by raymarine. • ensure that any non-raymarine cables are of the correct quality and gauge. For example...
4.3 power connection both connections need power to be supplied from each network i.E. The seatalk ng connection is powered by the seatalk ng backbone or seatalk ng device and the engine (devicenet) connection is powered from the engine’s can bus network. The information in this section relates to p...
4.4 data and control connections the illustrations below are examples of how the unit can be connected to seatalk ng and a compatible engine’s can bus to enable engine data transmission and steering control. Important: raymarine does not recommend that the eci-100 is used on the same can bus as othe...
Chapter 5: mounting chapter contents • 5.1 mounting the unit mounting 23.
5.1 mounting the unit the eci is designed to be surface mounted. Before mounting the unit ensure that you have: • identified the routes that the cables will take. D12973-1 1. Switch off the vessel’s power supply. 2. Check the selected location for the unit, a clear, flat area is required, which is s...
Chapter 6: system checks and troubleshooting chapter contents • 6.1 initial power on test • 6.2 further information • 6.3 troubleshooting system checks and troubleshooting 25.
6.1 initial power on test once your product is fully connected and installed, perform an initial power on test to verify correct operation. 1. Switch on the vessel’s power supply. 2. Look at the diagnostics leds. • during power up the leds will be illuminated red (power up usually takes approximatel...
System data troubleshooting aspects of the installation can cause problems with the data shared between connected equipment. Such problems, their possible causes and solutions are described here. Problem possible causes possible solutions check the data bus (e.G. Seatalk ng ) wiring and connections....
Led indications this product contains 2 diagnostic leds, one for the seatalk ng connection and one for the engine can bus connection. The leds for this product flash (blink) in set sequences which provides information on the current status of the unit for diagnostics and troubleshooting purposes. Le...
Chapter 7: maintenance chapter contents • 7.1 routine checks • 7.2 unit cleaning instructions maintenance.
7.1 routine checks the following periodic checks should be made: • examine cables for signs of damage, such as chafing, cuts or nicks. • check that the cable connectors are firmly attached and that their locking mechanisms are properly engaged. Note: cable checks should be carried out with the power...
Chapter 8: technical support chapter contents • 8.1 raymarine customer support • 8.2 viewing product information technical support.
8.1 raymarine customer support raymarine provides a comprehensive customer support service. You can contact customer support through the raymarine website, telephone and e-mail. If you are unable to resolve a problem, please use any of these facilities to obtain additional help. Web support this con...
Chapter 9: technical specification chapter contents • 9.1 technical specification technical specification.
9.1 technical specification physical specification dimensions • length : 109.2 mm (4.3 in) • height : 30.2 mm (1.19 in) • width : 21.35 mm (0.84 in) weight 43 g (1.52 oz) power specification seatalk ng engine can bus (devicenet) nominal supply voltage 12 v dc 12 to 24 v dc operating voltage range 10...
Chapter 10: spares and accessories chapter contents • 10.1 spares and accessories • 10.2 seatalk ng cables and accessories spares and accessories.
10.1 spares and accessories engine specific adaptor cables description engine connector eci connector part number volvo evc link cable – 1 m (3.3 ft) e70240 yamaha command link plus cable – 1 m (3.3 ft) e70242 y loom cables description engine connectors (black) adaptor cable connector (gray) part nu...
Description part no notes seatalk ng inline terminator a80001 provides direct connection of a spur cable to the end of a backbone cable. No t-piece required. Seatalk ng blanking plug a06032 acu / spx seatalk ng spur cable 0.3 m (1.0 ft) r12112 connects an spx course computer or an acu to a seatalk n...
Appendix a supported messages the table below shows a list of the standard parameters and messages that the unit supports. Standard j1939 engine parameter pgn spn engine speed 61444 190 engine oil temperature 65262 175 engine temperature 65262 110 engine oil pressure 65263 100 engine coolant pressur...