- DL manuals
- Raymarine
- Marine GPS System
- gS125
- Installation And Operation Instructions Manual
Raymarine gS125 Installation And Operation Instructions Manual
Summary of gS125
Page 1
Gs series installation and operation instructions english date: 10-2014 document number: 81344-6-en © 2014 raymarine uk limited release 12 gs series.
Page 3
Document and software changes the following tables describe the main changes that have been made since the last release of both the product software and this document. • applicable software version: lighthouse ii — release 12.Xx • applicable documents: 81344–6 • applicable products: gs95 / gs125 / g...
Page 4
Description applicable application applicable chapter(s) or section(s) changed ip camera connections section to show the ethernet coupler instead of the cross over coupler and added parts numbers for adaptor cable and ethernet coupler. N/a • 4.12 ip camera connections added ip camera guidance to ip ...
Page 5
Contents chapter 1 important information.......................... 9 certified installation ..................................................... 9 product operation in high temperatures ....................... 10 power over ethernet (poe)......................................... 11 tft displays ......
Page 6
7.2 gps status........................................................ 104 7.3 raymarine gps / gnss receiver compatibility ............................................................ 105 7.4 radar check ...................................................... 106 7.5 sonar check ........................
Page 7
19.7 the sonar image .............................................. 262 19.8 depth range ................................................... 263 19.9 sidevision tm range ........................................ 264 19.10 fishfinder scrolling ......................................... 264 19.11 fishfi...
Page 8
26.10 glossary of weather terms .............................. 383 chapter 27 sirius audio application (north america only)..................................................... 385 27.1 sirius audio overview........................................ 386 chapter 28 mobile applications.....................
Page 9
Chapter 1: important information certified installation raymarine recommends certified installation by a raymarine approved installer. A certified installation qualifies for enhanced product warranty benefits. Contact your raymarine dealer for further details, and refer to the separate warranty docu...
Page 10
Warning: radar transmission safety the radar scanner transmits electromagnetic energy. Ensure all personnel are clear of the scanner when the radar is transmitting. Warning: sonar operation • never operate the sonar with the vessel out of the water. • never touch the transducer face when the sonar i...
Page 11
Caution: product cleaning when cleaning products: • if your product includes a display screen, do not wipe the screen with a dry cloth, as this could scratch the screen coating. • do not use abrasive, or acid or ammonia based products. • do not use a jet wash. Power over ethernet (poe) this product ...
Page 12
Memory cards and chart cards microsd memory cards can be used to back up / archive data (e.G. Waypoint, and tracks). Once data is backed up to a memory card old data can be deleted from the system, creating capacity for new data. The archived data can be retrieved at any time. Chart cards provide ad...
Page 13
Uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful ...
Page 14
Connections to other equipment requirement for ferrites on non-raymarine cables if your raymarine equipment is to be connected to other equipment using a cable not supplied by raymarine, a suppression ferrite must always be attached to the cable near the raymarine unit. Declaration of conformity ray...
Page 15
Chapter 2: document and product information chapter contents • 2.1 handbook information on page 16 • 2.2 handbook conventions on page 17 • 2.3 product overview on page 19 • 2.4 system feature highlights on page 20 document and product information 15.
Page 16
2.1 handbook information this handbook contains important information regarding your multifunction display. The handbook is for use with gs series multifunction displays. About this handbook this handbook describes how to operate your multifunction display in conjunction with compatible electronic c...
Page 17
2.2 handbook conventions the following conventions are used throughout this handbook when referring to: type example convention icons the term "select" is used in procedures involving icons to refer to the action of selecting an on-screen icon, either using touch or physical buttons: • touch — press...
Page 18
Type example convention with the numeric adjust control displayed you can also select on the keypad icon or press and hold the ok button to open a numeric keypad to enter a new value for the setting. Slider bar controls the term “adjust” is used in procedures involving slider bar controls to refer t...
Page 19
2.3 product overview product information gs series multifunction displays (mfds) are touchscreen displays which have hybridtouch functionality when paired with a remote keypad. The following raymarine mfd variants are available. Model part number gs95 e70124 gs95 inverted e70183 gs125 e70125 gs125 i...
Page 20
2.4 system feature highlights features that enable you to connect and control a complete marine electronics system. Feature benefits what it is how to use it control your entire marine electronics system from one display. Alternatively, create a network of several displays to control your system fro...
Page 21
Feature benefits what it is how to use it custom “application panes”, each one representing a different combination of “channels” (frequencies) to suit different user scenarios. Note: not all mfds include an internal sonar module. An external sonar module may be required for fishfinder operation. Re...
Page 22
Feature benefits what it is how to use it control an autopilot system. • with a suitable connected evolution autopilot system, you can control an autopilot directly from your mfd, without a separate dedicated pilot control head. • make the most of raymarine’s automagic™ technology. Evolution autopil...
Page 23
Feature benefits what it is how to use it view and record ip cameras. Ip video cameras provide powerful networking capabilities and have many monitoring uses: • security. • engine room. • rear of boat. • docking. • any regular surveillance. • mast-top camera. • the mfd can be set up to continuously ...
Page 24
Feature benefits what it is how to use it control your vessel’s electrical systems the digital switching (“switch panel”) application and optional empirbus™ digital switching modules allow you to take control of your vessel's electrical systems: • control lighting. • monitor ac and dc electrical sys...
Page 25
Feature benefits what it is how to use it you own custom pages to suit your exact needs. Choose any combination of applications for each page — chart / sonar, chart / radar, chart / thermal camera and so on. • each application can be customized to suit you with comprehensive “setup” options. Configu...
Page 26
26 gs series.
Page 27
Chapter 3: planning the installation chapter contents • 3.1 system integration on page 28 • 3.2 installation checklist on page 33 • 3.3 multiple data sources (mds) overview on page 33 • 3.4 identifying your display variant on page 34 • 3.5 networking constraints on page 34 • 3.6 typical systems on p...
Page 28
3.1 system integration your multifunction display is compatible with a wide range of marine electronics devices. R ay240 1 2 8 5 6 7 3 16 10 9 11 12 13 15 4 18 17 19 20 21 22 23 24 d12890-1 14 0 0 0 0 0 0 a udio 0 0 0 antenna 0 network 0 0 p ower 00 0 0 tack true/app display vmg the display uses a n...
Page 29
Item device type maximum quantity suitable devices connections 3 vessel tank sensors — third-party • up to 5 x fuel. • 1 x fresh water. • 1 x waste water. • 1 x sewage. • 1 x bait / fish. Third-party nmea 2000 interfaces nmea 2000 (via optional devicenet adaptor cables) 4 gps / gnss receiver (extern...
Page 30
Item device type maximum quantity suitable devices connections • s2 • s3 8 ais — raymarine ® 1 • ais350 • ais650 • ais950 • ais250 • ais500 seatalk ng® , or nmea 0183 8 ais — third-party 1 third-party nmea 0183–compatible ais class a or class b receiver / transceiver nmea 0183 9 vessel trim tabs — t...
Page 31
Item device type maximum quantity suitable devices connections 17 raymarine ® sirius marine weather / satellite radio receiver (north america only) 1 seatalk hs : • sr150 • sr100 • sr6 seatalk ng® : • sr50 seatalk hs , seatalk ng® 18 additional multifunction display(s) — raymarine ® 9 3rd generation...
Page 32
Item device type maximum quantity suitable devices connections 23 fusion entertainment systems multiple fusion 700 series entertainment systems: • ms-ip700 • ms-av700 seatalk hs 24 pc / laptop 1 windows-compatible pc or laptop running raymarine voyager planning software. Seatalk hs note: raymarine ®...
Page 33
3.2 installation checklist installation includes the following activities: installation task 1 plan your system. 2 obtain all required equipment and tools. 3 site all equipment. 4 route all cables. 5 drill cable and mounting holes. 6 make all connections into equipment. 7 secure all equipment in pla...
Page 34
3.4 identifying your display variant to discover which model display you have follow the steps below: from the homescreen: 1. Select set-up. 2. Select maintenance. 3. Select diagnostics. 4. Select select device. 5. Search the network column for the 'this device' entry. 6. The device column for this ...
Page 35
Note: • all mfds must have lighthouse ii release v10.41 software or later to enable multiple sonar support. • sonar modules should be updated to the latest available software version to ensure compatibility. Incompatible displays if you connect a multifunction display to your system that is not comp...
Page 36
3.6 typical systems the illustrations below show examples of possible system configurations. For more details on compatible devices please refer to 3.1 system integration . Example: basic system seatalk ng seatalk hs / raynet raynet seatalk hs / raynet 0 0 d12891-1 1 3 2 4 5 6 8 7 1. Multifunction d...
Page 37
2. Weather sensor. 3. Sirius weather receiver. 4. Sonar module. 5. Seatalk ng pilot controller. 6. Seatalk ng instrument display. 7. Ais receiver / transceiver. 8. Audio system. 9. Smartphone / tablet. 10. Remote keypad. 11. Devicenet spur (for nmea 2000 devices). 12. Network switch. 13. Multifuncti...
Page 38
3.7 system protocols your multifunction display can connect to various instruments and displays to share information and so improve the functionality of the system. These connections may be made using a number of different protocols. Fast and accurate data collection and transfer is achieved by usin...
Page 39
3.8 data master any system containing more than one networked multifunction display must have a designated data master. The data master is the display which serves as a primary source of data for all displays, it also handles all external sources of information. For example the displays may require ...
Page 40
Hd-sdi additional parts supplied the gs195 is supplied with the following additional parts for use with the hd-sdi connection. D13051-2 1 2 3 1 protective boot 2 75 ohm bnc connector 4 cable ties x 2 (to secure the protective boot) 3.10 tools required for installation d12171-2 1 4 5 3 8 7 6 2 1. Pow...
Page 41
3.11 selecting a location warning: potential ignition source this product is not approved for use in hazardous/flammable atmospheres. Do not install in a hazardous/flammable atmosphere (such as in an engine room or near fuel tanks). General location requirements when selecting a location for your pr...
Page 42
Caution: mounting surface requirements this product is heavy. To prevent potential damage to the product and / or your vessel, observe the following before installing the product: • refer to the weight information provided in the technical specification for this product and ensure that the intended ...
Page 43
D 36 mm (1.4 in) e 39.2 mm (1.5 in) f 90 mm (3.5 in) planning the installation 43.
Page 44
44 gs series.
Page 45
Chapter 4: cables and connections chapter contents • 4.1 general cabling guidance on page 46 • 4.2 gs95 / gs125 / gs165 connections overview on page 47 • 4.3 gs195 connections overview on page 47 • 4.4 power connection on page 48 • 4.5 card reader connection on page 51 • 4.6 auxiliary alarm connecti...
Page 46
4.1 general cabling guidance cable types and length it is important to use cables of the appropriate type and length • unless otherwise stated use only standard cables of the correct type, supplied by raymarine. • ensure that any non-raymarine cables are of the correct quality and gauge. For example...
Page 47
4.2 gs95 / gs125 / gs165 connections overview details of the connections available on the multifunction display are shown below. D12700-1 1 2 4 5 6 3 1 seatalk ng 2 hdmi 3 3 x poe / raynet seatalk hs 4 card reader 5 video in / alarm out 6 power / nmea 0183 / video in 4.3 gs195 connections overview d...
Page 48
4.4 power connection 1 2 4 5 7 3 8 6 9 d12715-1 1. Multifunction display connections. 2. Power and data cable. 3. Connection to 12/24 v power supply. 4. Red cable (positive). 5. Fuse. 6. Black cable (negative). 7. Video input cable. 8. Nmea 0183 data cables. 9. Ground (drain) wire (thin black wire; ...
Page 49
6. Vessel battery 7. Vessel rf ground point connection battery connection with no rf ground if your vessel does not have a distribution panel or an rf ground point then your product may be wired directly to the battery with the drain wire also connected to the battery’s negative terminal. D13019-1 2...
Page 50
Touchscreen interference in exceptional circumstances, due to the proximity of certain electronic equipment that may be on the vessel the touchscreen may become unresponsive due to electrical interference. In the unlikely event of this occurring the interference can be suppressed by adding a groundi...
Page 51
4.5 card reader connection the card reader must be connected directly to the dedicated card reader connector on the rear of the display. Note: do not use cable extensions when connecting the card reader to the display. D12698-1 1 2 • multifunction display. • card reader. Note: the card reader must b...
Page 52
4.7 network connections you can connect a number of digital devices to your multifunction display using the network connector(s) at the rear of the unit. A typical network of digital devices may include: • up to 6 raymarine multifunction displays. • seatalk hs and raynet digital devices such as a so...
Page 53
The product can power up to 3 devices using the available network / poe ports as long as the combined max power of the poe devices does not exceed 20 watts. When a poe device is connected it is interrogated to establish if the device is poe and if so what class of device it is. The max power for tha...
Page 54
4.8 keypad connection the keypad can be connected directly to a multifunction display’s network connector or via a network switch. Multiple keypads can be connected to a system. Each keypad can be used to control up to 4 multifunction displays. If the network does not provide power over ethernet (po...
Page 55
4.9 radar connection the multifunction display is compatible with raymarine non-hd digital radomes and hd / superhd radar scanners. The scanner is connected using over seatalk hs . The radar is usually connected via a raymarine network switch. On smaller systems (with only 3 network devices) the rad...
Page 56
D 12254-1 1 4 2 3 1. Radar extension cable. 2. Radar power and data digital cable. 3. Raymarine network switch (or crossover coupler if connecting radar directly to display). 4. Raynet cable (or raynet to seatalk hs cable if connecting via crossover coupler). Note: the extension cable connects to th...
Page 57
Note: the maximum length for the radar power and data digital cable (including any extensions) is 25 m (82 ft). 4.10 sonar module connection a sonar connection is required for fishfinder applications. The multifunction display can be used with the following sonar modules: • cp450c • cp300 • cp100 no...
Page 58
Sonar variant multifunction display connection the gs series multifunction display can also be networked to raymarine multifunction display that has a built-in sonar module. Seatalk hs / raynet 4 3 d12898-1 1 2 1. Gs multifunction display. 2. Sonar variant multifunction display (e.G. E97). 3. Sonar ...
Page 59
4.11 thermal camera connection you can connect a thermal camera to your gs series multifunction display. The camera is usually connected via a raymarine network switch. If you want to use the optional joystick control unit (jcu) with the camera this must also be connected to the network switch. A co...
Page 60
4.12 ip camera connections you can connect ip cameras to your multifunction display. Note: compatible ip cameras must be able to be configured to: • automatically assign an ip address via dhcp prior to connecting to your multifunction display or network. • allow unauthenticated, anonymous onvif acce...
Page 61
4.13 weather receiver connection you can connect a sirius xm weather receiver to your multifunction display. Raynet 0 0 0 0 0 0 a udio 0 0 0 antenna 0 network 0 0 power 0 0 d12902-2 1 2 1. Raymarine weather receiver. 2. Multifunction display. The weather receiver can also be connected to a raymarine...
Page 62
Network connection 6 d12905-1 6 5 1 2 3 4 1. Network switch. 2. Fusion system. 3. Raynet to seatalk hs adaptor cable. 4. Fusion ethernet connector. 5. Second fusion system (the multifunction display can be connected to multiple fusion entertainment systems). 6. Networked multifunction displays. Note...
Page 63
4.16 ais connection a compatible ais can be connected using seatalk ng or nmea 0183. Connection using seatalk ng d12908-1 seatalk ng 2 1 1. Multifunction display. 2. Seatalk ng ais receiver / transceiver. Connection using nmea 0183 nmea0183 (38400) nmea 0183 (4800) 3 1 2 d12909-1 1. Vhf radio. 2. Ai...
Page 64
4.18 seatalk ng connections the display can connect to a seatalk ng network. The display can use seatalk ng to communicate with: • seatalk ng instruments (for example, i70). • seatalk ng pilot control head (for example, p70). • seatalk ng autopilots (for example, evolution autopilots or smartpilot s...
Page 65
4.19 nmea 2000 connection the display can receive data from nmea 2000 devices (e.G. Data from compatible engines). The nmea 2000 connection is made using seatalk ng and appropriate adaptor cables. You can either: • use your seatalk ng backbone and connect each nmea 2000 device on a spur, or • connec...
Page 66
4.21 nmea 0183 connection nmea 0183 devices can be connected to the multifunction display using the power and data cable. 6 1 2 3 4 5 11 7 8 9 10 12 nmea device 4800 / 38400 baud nmea device 4800 / 38400 baud d12714-1 nmea 0183 devices are connected using the supplied power and data cable. The displ...
Page 67
4.22 camera / video connections a camera or a video device can be connected directly your multifunction display using the video connector on the power and data cable or using the dedicated video / alarm connector. Examples of video sources that you can connect to the display include: • video camera....
Page 68
4.24 hd-sdi connection (gs195) the gs195 includes a high definition serial digital interface (hd-sdi), which can be used to view a compatible video source using the multifunction display’s camera application. D13045-2 3 1 2 1. Hd-sdi camera 2. Hd-sdi input data cable 3. Gs195 multifunction display n...
Page 69
4.25 media player connection you can use your multifunction display to wirelessly control a bluetooth-compatible media player (such as a smartphone). The media player must be compatible with the bluetooth avrcp protocol (version 2.1 or higher). D12917-1 1 3 2 1. Multifunction display. 2. Bluetooth c...
Page 70
Selecting back will hide the audio controls. Media player controls using a remote control you can control audio wirelessly using a raymarine rcu-3 remote control unit. The shortcut key on the rcu-3 must be set to start/stop audio playback, refer to the using a remote control section for further deta...
Page 71
Your multifunction display, with the homescreen displayed: 1. Select set-up. 2. Select system settings. 3. Select wireless connections. 4. Select bluetooth > on. 5. Select new bluetooth connection. A pop-up message will be displayed to confirm that the device you are connecting to is discoverable. 6...
Page 72
4.27 remote control functions ra n g e bu tto n s p a ir s e le c t o r d 12051-2 arrow buttons shortcut button button application where function available: default functions: chart radar fishfinder weather home- screen range / zoom. • press up or down arrow for momentary response. • hold up or down...
Page 73
Button application where function available: customizable functions: open homescreen. Shortcut switch active application (only available when multiple applications are displayed). Shortcut reconnecting the rcu 1. When you pair the rcu-3 with a multifunction display a wireless connection is establish...
Page 74
4.28 wifi connections raymarine mobile app connection you can use compatible tablet and smartphone devices as a wireless repeat display or remote control for your multifunction display. Raymarine apps allow you to stream and / or control, remotely what you see on your multifunction display to a comp...
Page 75: Chapter 5: Mounting
Chapter 5: mounting chapter contents • 5.1 bracket mounting hole locations on page 76 • 5.2 mounting surface requirements on page 76 • 5.3 flush mounting the display on page 77 • 5.4 flush mounting the card reader on page 78 • 5.5 surface mounting the display on page 79 • 5.6 surface mounting the ca...
Page 76
5.1 bracket mounting hole locations the location of the bracket mounting holes on each display variant is shown below. 1 1 1 1 2 2 2 2 3 3 3 3 d12727-1 1 gs165 and gs195 bracket mounting hole locations 2 gs125 bracket mounting hole locations 3 gs95 bracket mounting hole locations 5.2 mounting surfac...
Page 77
5.3 flush mounting the display for flush mounting you must rebate the mounting surface. D12706-1 1. Check the selected location for the unit. A clear, flat area with suitable clearance behind the panel is required. 2. Before modifying the mounting surface, refer to the dimensions supplied in this do...
Page 78
13. Using a suitable sized wrench tighten the lock nut against the washer and the mounting bracket to lock in position. The lock nut should be tightened sufficiently to securely hold the display in position. Do not overtighten. Note: the supplied gasket provides a seal between the unit and a suitabl...
Page 79
5.5 surface mounting the display 1. Check the selected location for the unit. A clear, flat area with suitable clearance behind the panel is required. 2. Before modifying the mounting surface, refer to the dimensions supplied in this document to ensure there is enough space for the display and all c...
Page 80
12. Using a suitable sized wrench tighten the lock nut against the washer and the mounting bracket to lock in position. The lock nut should be tightened sufficiently to securely hold the display in position. Do not overtighten. Note: the supplied gasket provides a seal between the unit and a suitabl...
Page 81
Chapter 6: getting started chapter contents • 6.1 display power on page 82 • 6.2 controls on page 83 • 6.3 homescreen overview — touch only displays on page 85 • 6.4 pages on page 87 • 6.5 applications on page 88 • 6.6 splitscreen controls on page 89 • 6.7 screen overview on page 90 • 6.8 basic touc...
Page 82
6.1 display power powering the display on 1. Press the power button on the display. 2. Select accept to acknowledge the disclaimer message. Putting the display into standby 1. Press and hold the power button until the countdown reaches zero. If the power button is released before the countdown reach...
Page 83
6.2 controls d12701-1 1 2 3 descrip- tion functions 1 touch- screen touch the screen to operate functions, including all menu operations. 2 power • press once to switch the unit on. • when powered on, press the power button again open the shortcuts page. • when powered on, press and hold to put the ...
Page 84
Unicontrol non-touch, hybridtouch and the remote keypad include a unicontrol which consists of rotary, joystick and a push button control. D12180-1 1 2 3 1. Rotary — use this to select menu items, move the on-screen cursor, and adjust the range in the chart and radar applications. 2. Joystick — use ...
Page 85
6.3 homescreen overview — touch only displays the homescreen provides a central point of access for your display's applications, data and settings. • the homescreen provides quick access to your data (waypoints, routes, tracks, images and videos) and backup settings. • the homescreen consists of a n...
Page 86
Radar scanner status symbols the radar scanner power mode status is indicated in the databar. Symbol radar power mode description trans- mit (tx) rotating icon, signifying that the scanner is on and transmitting. When scanner is set to on, select this mode to activate the scanner. This is the usual ...
Page 87
6.4 pages pages are made up of 1 to 4 panes that are used to display applications on your multifunction display (mfd). Pages are accessed using the icons on the homescreen. • you can create up to 2 application panes per page using an mfd that has a screen size of 7 inches or less. • you can create u...
Page 88
4. Select the page icon that you want to move. 5. Select the page icon that you want to swap positions with. The page icon is moved to the new position. Renaming a page on the homescreen with the homescreen displayed: 1. Select the customize icon. 2. Select homescreen. 3. Select rename page. 4. Sele...
Page 89
Fusion link application — link to and control a compatible fusion entertainment system from your multifunction display. Sirius audio application — control sirius radio from your multifunction display. User manual — opens the english version of the product user manual stored on the display. To open t...
Page 90
3. Use the range in or range out controls to switch the active application between splitscreen and fullscreen views. Switching the active pane or display using the keypad the switch active button is used to switch the active pane on a multi application page and / or to switch the active display. Wit...
Page 91
D12281- 4 3 4 5 1 2 screen item description 1 back — on displays with a touchscreen you can press the onscreen (back) icon to go back to a previous menu. On non-touchscreen displays or hybridtouch displays use the back button. 2 close — on displays with a touchscreen you can press the onscreen x (cl...
Page 92
1 decrease display brightness 2 increase display brightness 3 power up / power down radar 4 radar standby / radar transmit 5 autopilot standby (during active navigation) 6 display pilot control dialog 7 powersave mode 8 screenshot / screen capture edit dialogs edit dialogs enable you to edit the det...
Page 93
Using slider bar controls slider bar controls provide a graphical representation of numeric data and enables you to quickly change setting values. 1 2 3 d12570-1 item descrip- tion non—touch operation touch operation 1 current value n/a n/a 2 slider control use the rotary control to adjust value sli...
Page 94
6.9 multi-touch gestures raymarine a series and gs series multifunction displays support multi-touch. Multi-touch means that the display is capable of recognizing multiple simultaneous touch inputs. This means that you can use 2 or more fingers on the screen at the same time to perform multi-touch g...
Page 95
1. Press the power button once. The shortcuts menu is displayed. 2. Adjust the brightness to the required level using the on-screen brightness slider bar control, or 3. Touch the sun icon to increase the brightness level or the moon icon to decrease the brightness level. Note: the brightness level c...
Page 96
• routes and waypoints • radar • sonar • data received from the autopilot, instruments, the engine and other external sources. Your system may be wired for redundancy with data connections made to repeat displays. However these connections will only become active in the event of a fault and/or reass...
Page 97
6.11 enabling autopilot control enabling the autopilot control function — seatalk and spx seatalk ng autopilots to enable control of your seatalk or spx seatalk ng autopilot using your multifunction display follow the steps below. From the homescreen: 1. Select set-up. 2. Select system settings. 3. ...
Page 98
6.12 engine identification engine data can be displayed on your mfd using the data application, which provides some preset engine pages for displaying some of the most common types of engine data. Important: before you can display engine data on your mfd, you must: • ensure that your mfd is running ...
Page 99
Engine setup with an eci interface before you can display engine data on your mfd, you may need to use the "engine identification wizard” on the mfd to setup the engines. Important: when setting up on a multiple engine system, engines should always be turned on in sequence from port to starboard. Th...
Page 100
6.13 enabling ais functions before proceeding ensure your ais unit is connected to nmea port 1. With the homescreen displayed: 1. Select set-up. 2. Select system settings. 3. Select nmea set-up. 4. Select nmea input port 1. 5. Select the ais 38400 option. 6. Select back to return to the system setti...
Page 101
6.15 software updates raymarine’s multifunction display software is updated regularly to provide new and enhanced features and improved performance and usability. You should ensure you have the latest software by regularly checking the raymarine website for new software. You can identify your multif...
Page 102
14. If you have a remote keypad connected then select yes to update the keypad software update. When the software update process has been completed a confirmation pop-up is displayed. 15. Select ok to confirm. 16. Remove the microsd card from the card reader. 17. Perform a factory reset of your mult...
Page 103: Chapter 7: System Checks
Chapter 7: system checks chapter contents • 7.1 gps check on page 104 • 7.2 gps status on page 104 • 7.3 raymarine gps / gnss receiver compatibility on page 105 • 7.4 radar check on page 106 • 7.5 sonar check on page 107 • 7.6 thermal camera setup and checks on page 108 system checks 103.
Page 104
7.1 gps check checking gps operation you can check that the gps is functioning correctly using the chart application. 1. Select the chart page. 2. Check the screen. With the chart displayed, you should see: your boat position (indicates a gps fix). Your current position is represented by a boat symb...
Page 105
Including satellite geometry, system errors in the data transmission and system errors in the receiver. A higher figure signifies a greater positional error. A typical receiver has an accuracy of between 5 and 15 m. As an example, assuming a receiver error of 5 m, an hdop of 2 would represent an err...
Page 106
7.4 radar check warning: radar scanner safety before rotating the radar scanner, ensure all personnel are clear. Warning: radar transmission safety the radar scanner transmits electromagnetic energy. Ensure all personnel are clear of the scanner when the radar is transmitting. Checking the radar fro...
Page 107
7.5 sonar check sonar transducer and sonar module selection you must select the sonar transducer and sonar module that you want to use in the displayed fishfinder application pane. Sonar module selection • sonar and downvision tm variant displays are fitted with an internal sonar module. • all varia...
Page 108
D9343--2 1 2 3 1 waterline offset 2 transducer / zero offset 3 keel offset if an offset is not applied, displayed depth readings represent the distance from the transducer to the sea bed. Setting the depth offset from the fishfinder application: 1. Select menu. 2. Select set-up. 3. Select transducer...
Page 109
Unicontrol joystick — is used for rotating the camera left or right (panning), or tilting the camera up or down. Unicontrol rotary — is used to zoom in and out. Resetting the thermal camera to the home position when connected to a pan, tilt thermal camera the home position of the camera can be set. ...
Page 110
110 gs series.
Page 111
Chapter 8: managing display data chapter contents • 8.1 memory cards and chart cards on page 112 • 8.2 inserting a memory card or chart card on page 112 • 8.3 removing a memory card or chart card on page 113 • 8.4 saving user data and user settings on page 113 • 8.5 save and restore items on page 11...
Page 112
8.1 memory cards and chart cards microsd memory cards can be used to back up / archive data (e.G. Waypoint, and tracks). Once data is backed up to a memory card old data can be deleted from the system, creating capacity for new data. The archived data can be retrieved at any time. Chart cards provid...
Page 113
8.3 removing a memory card or chart card from the homescreen: 1. Select my data. 2. Select eject card. A message is displayed prompting you to select the memory device you want to eject. 3. Select sd1 for a memory card in the top card slot, or sd2 for a memory card in the bottom card slot. 4. Open t...
Page 114
5. Select save waypoints to card. The waypoint group list is displayed. 6. Select the group or groups you want to save, or select select all. 7. Select save. The on-screen keyboard is displayed. 8. Using the on-screen keyboard enter the filename you want to save the file as. 9. Select save. If your ...
Page 115
5. Browse to and select the file you want to import. A confirmation dialog is displayed. 6. Select ok. Note: when routes and tracks are imported they will be hidden by default, to display the imported routes and tracks please refer to the showing or hiding routes and tracks section. Erasing user dat...
Page 116
8.5 save and restore items the table below details the data items and settings which will be saved to and restored from a memory card on your multifunction display. Homescreen and settings menu setting homescreen default page configuration set-up > system settings autopilot control dsc alerts set-up...
Page 117
Menu setting databox 2 content presentation > vectors vector length vector width presentation > objects show rocks nav marks nav marks symbols light sectors routing systems caution areas marine features land features business services panoramic photos roads additional wrecks colored seabed areas ves...
Page 118
8.6 screenshots you can take a screenshot of what is currently displayed on the screen. Screenshots are saved to a microsd card in .Bmp (bitmap) format. The saved image can be viewed from any device capable of viewing bitmap images. Taking a screenshot you can take a screenshot by following the step...
Page 119
Chapter 9: customizing your display chapter contents • 9.1 language selection on page 120 • 9.2 boat details on page 121 • 9.3 units set-up on page 122 • 9.4 time and date set-up on page 123 • 9.5 display preferences on page 124 • 9.6 databar and databox overview on page 127 • 9.7 list of data items...
Page 120
9.1 language selection the system can operate in the following languages: english (us) english (uk) arabic bulgarian chinese croatian czech danish dutch finnish french german greek hebrew icelandic italian japanese korean norwegian polish portuguese (brazilian) russian slovenian spanish swedish turk...
Page 121
9.2 boat details you can customize various settings to make them specific to your vessel. Menu item description options boat type you can change the appearance of the vessel in the chart application. Select the option that most closely resembles the type and size of your vessel. Note: when boat type...
Page 122
9.3 units set-up you can specify your preference for the units of measurement that will be used in all applications. Menu item description options distance units the units of measure that will be used in all applications for the display of all values related to distance. • nautical miles • nm & m (m...
Page 123
9.4 time and date set-up you can specify your preference for the way that time and date will appear in all applications. Menu item description options date format allows you to specify the preferred format for the display of date information in all applications. • mm:dd:yy (month, day, year) • dd:mm...
Page 124
9.5 display preferences you can specify your preference for general display behavior. Menu item description options starting page allows you to select what page the display opens at start up. • homescreen (default) • last page — after power up the last used page is displayed. • choose page — after p...
Page 125
Menu item description options note: this option is only available on displays with multiple card reader slots. • microsd 2 onscreen range controls you can enable and disable onscreen range controls on new e series and gs series displays by following the steps below. From the homescreen: 1. Select cu...
Page 126
6. Select an appropriate brightness group. 7. Repeat the process for the other displays you want in the brightness group. If the display is not a multifunction display, refer to the documentation that accompanies the unit for instructions on setting-up shared brightness. 8. Once all required display...
Page 127
9.6 databar and databox overview you can customize the data displayed in the databar and onscreen databoxes. Customizable data is displayed in the databar, extended databar (hybridtouch displays only) or databoxes. The databar, extended databar and databoxes are available in all applications. These ...
Page 128
Customizing the databar from the homescreen: 1. Select customize. 2. Select databar set-up. 3. Select edit databar. 4. In the databar, select the cell that you want to change. The select data category menu will be displayed. 5. Select the category that reflects the type of data you want to display i...
Page 129
9.7 list of data items categories of data available to display in the data application, databoxes, databar, and expanded databar are shown below. Dial graphics are not available in databoxes or databars. The following table shows the data items available by category. Data category description data i...
Page 130
Data category description data item data application graphics rpm rpm & sog coolant temperature coolant pressure oil temperature oil pressure oil pressure & coolant temperature transmission oil temperature transmission oil pressure transmission gear boost pressure fuel pressure fuel flow rate fuel f...
Page 131
Data category description data item data application graphics fuel level (%) total fuel (%) total fuel (vol) fuel flow total economy estimated fuel remaining distance to empty time to empty fuel used (trip) fuel** types of data related to the fuel system. For example, fuel levels. Fuel used (season)...
Page 132
Data category description data item data application graphics minimum water temperature maximum water temperature vessel position cog & sog cog sog maximum sog gps gps-related data. For example, vessel position. Average sog heading heading and speed (data application only.) locked heading locked hea...
Page 133
Data category description data item data application graphics waypoint info active waypoint name target position bearing to waypoint btw & dtw (data application only.) course made good cmg & dmg cmg & vmg (data application only.) distance to waypoint distance made good waypoint eta waypoint ttg rout...
Page 134
Data category description data item data application graphics fresh water (%) grey water (%) black water (%) tanks** data related to water tanks live well (%) local time time time-related data. For example, local time. Local date awa maximum awa minimum awa aws maximum aws minimum aws twa maximum tw...
Page 135
Data category description data item data application graphics awa & aws awa (ch) and aws awa and vmg twa & tws twa (ch) and tws twa and vmg gwd and beaufort gwd & gws none note: *dials and graphical representations are only available from the data application. Databar and data cell overlays can only...
Page 136
9.8 system set-up menus the system set-up menus enable you to configure your display and connected external devices. The following menus are available: menu item description notes touch-lock enables you to lock the touchscreen of a touch only display when the display is paired with a remote keypad. ...
Page 137
Ground trip resets menu this menu enables you to resets the chosen ground trip distance counter to zero. Menu item description ground trip 1 reset resets the ground trip 1 distance counter to zero. Ground trip 2 reset resets the ground trip 2 distance counter to zero. Ground trip 3 reset resets the ...
Page 138
Note: glonass satellites are only available when connected to a compatible receiver such as the built-in receiver of an a9x or a12x mfd. Satellite status area the satellite status area displays the following information about each satellite: • type — identifies which constellation the satellite belo...
Page 139
Data sources menu this menu enables you to select the external sensors and devices that will provide data to the display. Auto / manual selection each dialog enables you to view and select your preferred data source. Selection of data source can be manual or set to automatic: • auto — the display wi...
Page 140
External devices menu this menu enables you to configure the external devices connected to the display. Menu item description notes pilot set-up when connected to an evolution autopilot this option allows you to enable and disable pilot control and the pilot bar. You can also access certain pilot se...
Page 141
Connections menu this menu enables you to connect wireless bluetooth and wi-fi devices to the display. Menu item description options bluetooth enable or disable bluetooth on the display. • on • off (default) wi-fi enable or disable wi-fi on the display. • on • off (default) connection manager provid...
Page 142
Menu item description options • viewing only — rayview • remote control — rayremote or raycontrol • remote control 142 gs series.
Page 143
Nmea set-up menu this menu enables you to configure settings for nmea devices. Menu item description options bridge nmea heading if set to on, nmea heading data will be bridged onto the seatalk data bus, and will be sent to all nmea-connected devices. If set to off, nmea heading data will not be bri...
Page 144
System preferences menu menu item description options bearing mode determines how all bearing and heading data is displayed in. This does not affect how the chart or radar displays are drawn. • true (default) • magnetic variation source this setting compensates for the naturally occurring offset of ...
Page 145
Maintenance menu this menu provides access to systems settings reset and diagnostics. Menu item description options touchscreen alignment if the touchscreen is misaligned to your touch, you can realign it to improve the accuracy. Realignment involves a simple exercise to align an on-screen object wi...
Page 146
Diagnostics menu if you encounter problems with your multifunction display or peripheral devices you can use the diagnostics menu to view information about your device and connected equipment. Select device enables you to view a list of all devices connected to the seatalk hs network. You can also s...
Page 147
Chapter 10: document viewer application chapter contents • 10.1 document viewer overview on page 148 document viewer application 147.
Page 148
10.1 document viewer overview you can view pdf documents on your multifunction display. The document viewer is available from the homescreen and is used to view and search pdf documents (such as product handbooks). D12755-1 1 2 3 1 opens the microsd card file browser. 2 opens the user manual stored ...
Page 149
1. Select menu. 2. Select close file. The document is close and the main doc viewer page is displayed. Browsing an open document on touchscreen displays you can browse pdf documents as detailed below. With a pdf document open: • move your finger up to scroll down the document. • move your finger dow...
Page 150
• the find tool bar is displayed. • the first occurrence of the keyword is highlighted. 5. Move the joystick down to go to the next occurrence of the keyword, or 6. Move the joystick up to go to the previous occurrence of the keyword. 7. You can press the back button at any time to close the find to...
Page 151
Chapter 11: autopilot control chapter contents • 11.1 autopilot control overview and features on page 152 • 11.2 enabling autopilot control on page 152 • 11.3 engaging the autopilot on page 153 • 11.4 adjusting the current locked heading on page 153 • 11.5 disengaging the autopilot on page 154 • 11....
Page 152
11.1 autopilot control overview and features raymarine ® autopilots can be controlled directly from a compatible lighthouse powered mfd, with or without a dedicated pilot control head. Note: for information on connecting a raymarine ® autopilot to a compatible mfd, refer to the documentation that ac...
Page 153
11.3 engaging the autopilot engaging the autopilot using the pilot button on multifunction displays which have a dedicated pilot button or when using a remote keypad you can engage the autopilot using the pilot button. With the autopilot disengaged: 1. Press the pilot button. The pilot control dialo...
Page 154
11.5 disengaging the autopilot caution: disengaging the autopilot on integrated multifunction displays that do not have a dedicated pilot button, in an emergency the autopilot can be disengaged by pressing and holding the power button. Disengaging the autopilot using the power button on integrated m...
Page 155
11.6 manually displaying the pilot control dialog box you can also open the pilot control dialog at any time from the homescreen or chart application. 1. From the homescreen: i. Select set-up. Ii. Select pilot controls. 2. From the chart application: i. Select menu. Ii. Select navigate. Iii. Select ...
Page 156
Description 1 pilot status — current pilot mode. 2 current heading. 3 no (standby) — disengages the autopilot and returns to manual vessel control. 4 rudder bar — indicates the position of the rudder. 5 turn angle — the turn angle is only available for seatalk ng autopilots. This indicates the direc...
Page 157
11.9 pilot set-up when connected to an evolution autopilot the pilot set-up page is available. D12883-1 9 1 0 4 6 7 5 8 2 1 3 1 back — go back to the previous menu. 2 pilot status — current pilot mode. 3 close — closes the pilot set-up page and displays the homescreen. 4 pilot control — switches aut...
Page 158
When choosing a suitable vessel type, the emphasis should be on safe and dependable steering response. Important: if you change the vessel type after completing the dockside wizard, all commissioning settings will be reset to default settings, and you will need to complete the dockside wizard again....
Page 159
• bang-bang — bang-bang modes applies continuous rudder in the direction of the joystick movement, to improve control, the speed of rudder movement changes with the angle of the joystick. For maximum speed, push the joystick hard over. If you return the joystick to the center position, the rudder wi...
Page 160
If required this procedure will automatically correct the compass offset value accessible from the vessel settings menu. Note: if the alignment fails it means that the pilot sensor is more than a 10° deviation between your cog heading and the pilot sensor, in this situation the pilot sensor position...
Page 161
Type options are provided for guidance only. You may wish to experiment with the different vessel hull type options, as it might be possible to improve the steering performance of your vessel by selecting a different vessel type. When choosing a suitable vessel type, the emphasis should be on safe a...
Page 162
• if you already know the hard-over time for your vessel’s steering system: enter this time during the dockside wizard procedure. • if you do not know the hard-over time for your vessel’s steering system: skip this step during the dockside wizard by selecting save, complete the dockside wizard proce...
Page 163
• marine pontoons. • metal-hulled vessels. • undersea cables. Note: you can speed-up the linearization process by completing a 360 degree turn (at a speed of 3 – 15 knots). You can also restart the linearization process at any time by selecting the restart compass menu item. Use the compass deviatio...
Page 164
11.12 autopilot status symbols the autopilot status is indicated in the databar. Symbol description autopilot is in standby mode. Autopilot is in track mode. Autopilot is in auto mode. No autopilot detected. Autopilot alarm active. Dodge mode is active. Fish mode is active. Autopilot calibration. Po...
Page 165
Chapter 12: alarm management chapter contents • 12.1 alarms overview on page 166 • 12.2 alarm manager overview on page 166 • 12.3 alarm options on page 169 alarm management 165.
Page 166
12.1 alarms overview alarms alert you to a situation or hazard requiring your attention, such as shallow depth or a change in water temperature. Alarms are triggered by system functions, and external devices connected to the multifunction display (mfd). Audible and visual warnings are displayed on a...
Page 167
The alarm history tab provides details of alarms and the date and time that they were triggered and cleared / acknowledged. The alarm history can display up to 1,000 alarm events and displays them sorted by time. When the alarm history has reached its capacity of 1,000 entries, the oldest events in ...
Page 168
5. With the numeric adjust control displayed, select the on-screen up and down arrows to adjust the alarm threshold value, or 6. To use the numeric keypad: i. Select on the actual value or the keypad icon. The numeric keypad is displayed. Ii. Use the on-screen keypad to enter the desired value for t...
Page 169
12.3 alarm options safety alarms menu item description options waypoint arrival if enabled, when you arrive at a waypoint, an alarm is triggered. This setting allows you to specify the radius of the waypoint arrival circle. The waypoint arrival circle is an imaginary circle around the destination wa...
Page 170
Menu item description options safezone (ais targets alarm) ais target alarms can be enabled and disabled. With the ais target alarm disabled ais targets will not trigger the safezone alarm. Triggering of marpa target alarms cannot be disabled. Safezone (ais targets): • enabled (ticked) (default) • d...
Page 171
Menu item description options • 00.00 to 23:59 hrs (hh:mm) countdown timer when enabled, counts down the time period specified in the timer period setting, and triggers an alarm when zero is reached. Enable: • enabled (ticked) • disabled (un-ticked) (default) time period • 00:00:01 to 99:59:59 (hh:m...
Page 172
Menu item description options • –9.98°f to upper temp limit fish if the fish alarm is enabled, an alarm tone is triggered if a target is detected that meets the fish alarm sensitivity. The following options are available under fish alarm. • enable — enables and disables fish alarms. • fish alarm sen...
Page 173
Menu item description options • not charging • high boost pressure • rev limit exceeded • egr system • throttle position sensor • emergency stop • warning level 1 • warning level 2 • power reduction • maintenance needed • communications error • sub or secondary throttle • neutral start protect • eng...
Page 174
174 gs series.
Page 175
Chapter 13: man overboard (mob) chapter contents • 13.1 man overboard on page 176 man overboard (mob) 175.
Page 176
13.1 man overboard if you lose a person or object overboard, you can use the man overboard (mob) function to mark the position that the vessel was at when the mob function was activated. The mob function is available at all times, regardless of which application is running. Mob can be set to dead re...
Page 177
Cancelling the man overboard (mob) alarm on a multifunction display with physical buttons or when using a remote keypad you can cancel the mob alarm and resume normal operation follow the steps below: 1. Press and hold the wpt / mob button for 4 seconds. The mob alarm is cancelled and normal operati...
Page 178
178 gs series.
Page 179
Chapter 14: dsc vhf radio integration chapter contents • 14.1 dsc vhf radio integration on page 180 • 14.2 enabling dsc vhf radio integration on page 180 dsc vhf radio integration 179.
Page 180
14.1 dsc vhf radio integration you can connect your dsc vhf radio to your multifunction display and show distress message information and gps position data for other vessels. Connecting a dsc vhf radio to your multifunction display provides the following additional functionality: • distress messages...
Page 181: Chapter 15: Fuel Manager
Chapter 15: fuel manager chapter contents • 15.1 fuel manager overview on page 182 fuel manager 181.
Page 182
15.1 fuel manager overview the fuel manager provides an estimate of fuel remaining, and the distance and time which can be travelled before the tanks are empty. In order to calculate these values, you must configure the total capacity of fuel available to the engines and log each time you add fuel. ...
Page 183
• distance per volume • volume per distance • litres per 100km 6. Select the required economy units. 7. Select fuel calculations to select the desired method of calculation. The following options are available: • fuel used (pgn127497) • fuel flow rate note: if the fuel used (pgn127497) is not availa...
Page 184
2. Select presentation. 3. Select overlays. 4. Select fuel range ring so that on is selected. The fuel range ring pop-up message is displayed. 5. Select ok to turn on the fuel range rings. 184 gs series.
Page 185: Chapter 16: Ais Function
Chapter 16: ais function chapter contents • 16.1 ais overview on page 186 • 16.2 ais prerequisites on page 187 • 16.3 ais context menu on page 187 • 16.4 enabling ais on page 188 • 16.5 displaying ais vectors on page 188 • 16.6 ais status symbols on page 189 • 16.7 ais silent mode on page 189 • 16.8...
Page 186
16.1 ais overview the ais feature enables you to receive information broadcast by other vessels, and to add these vessels as targets in the chart and radar applications. With an optional ais unit connected to your system you can: • display targets for any other ais-equipped vessels. • display voyage...
Page 187
16.2 ais prerequisites you must have suitable ais hardware connected to your multifunction display to make use of the ais functionality. In order to run ais, you will need: • a receive-only ais unit or a full ais transceiver (a unit that sends and receives). • a vhf antenna. • a gps - to provide pos...
Page 188
16.4 enabling ais enabling ais in the chart application to enable the ais overlay in the chart application follow the steps below. To enable the ais overlay your system must include an ais receiver or transceiver. The ais overlay is not available in 3d view. From the chart application menu: 1. Selec...
Page 189
16.6 ais status symbols ais status is indicated by a symbol in the databar. Symbol description ais unit is switched on and operating. Ais currently unavailable. Ais unit is switched off, or not connected. Ais unit is in silent mode. Ais unit is in silent mode, with active alarms. Ais unit is connect...
Page 190
16.8 ais target symbols your multifunction display shows a range of symbols to represent the different types of ais target. Target type description symbol transmitting target target is moving or at anchor (target is not activated, dangerous or lost). Activated target target activated — that is, ais ...
Page 191
16.9 displaying detailed ais target information from the chart or radar application: 1. Select an ais target. The ais target context menu is displayed. 2. Select view ais data. Ais data the table below shows the ais target information which if available will be displayed on the multifunction display...
Page 192
16.11 using ais to avoid collisions you can use the ais safe zone and safety message functions to help you avoid collisions with other vessels and objects. Safe zones a safe zone is a ring centred on your vessel within which a target is considered dangerous. It is displayed in the radar or chart app...
Page 193
16.12 target options the target options menu for the chart application and radar application are shown below. Parameter description options vector length the length of the vector lines displayed depends on the distance that an ais target travels in the time period that you specify for this setting. ...
Page 194
16.13 ais alarms the ais functions generate a number of alarms to alert you to dangerous or lost targets. In addition to the dangerous target alarm, the system generates an alarm when a dangerous target becomes a lost target i.E. Its signal has not been received for 20 seconds. Your ais receiver gen...
Page 195
Enabling and disabling buddy tracking in the radar application from the radar application, with ais enabled: 1. Select menu. 2. Select targets. 3. Select display buddies. Selecting display buddies will switch the buddy tracking feature on and off. Adding a vessel to your buddy list in the chart or r...
Page 196
196 gs series.
Page 197
Chapter 17: waypoints, routes and tracks chapter contents • 17.1 waypoints overview on page 198 • 17.2 routes on page 207 • 17.3 tracks on page 215 • 17.4 import and export on page 217 • 17.5 waypoints, routes and tracks storage capacity on page 217 waypoints, routes and tracks 197.
Page 198
17.1 waypoints overview waypoints are position markers used for the purposes of navigation. Your multifunction display can create waypoints, which can then be selected for active navigation. There are a range of features for placing, navigating and managing waypoints, these can be accessed from the ...
Page 199
• goto waypoint • follow from here (only available when waypoint is part of a route.) • edit waypoint • erase waypoint • remove waypoint (only available when waypoint is part of a route.) • move waypoint • measure • build route • acquire target (only available if radar overlay is switched on.) • sle...
Page 200
Placing a waypoint at your vessel's position in addition to positional information, a waypoint placed at the vessel position will capture temperature and sounded depth information (if you have the appropriate sensors connected to your system). From the chart, radar or fishfinder application: 1. Sele...
Page 201
D13013-1 5 6 7 8 4 1 2 3 1. Sort by: — sort waypoints by name, range, symbol or date. 2. Search — search for waypoints using keywords. 3. Export — exports the waypoint group currently displayed to a memory card. 4. Waypoint group — this is the currently selected waypoint group. 5. Rename group — ren...
Page 202
Erasing a waypoint group before you can erase a waypoint group you must move or erase all the waypoints assigned to that group. With the waypoint group displayed: 1. Select the waypoint group that you want to erase. 2. Select erase group. The group is deleted from the system. Waypoint information wh...
Page 203
2. Select erase waypoint. The erase waypoint pop up message is displayed. 3. Select yes to confirm, or no to cancel. Erasing a waypoint using the waypoint list with the waypoint list displayed: 1. Select all waypoints. 2. Select the waypoint you want to erase. The waypoint information page is displa...
Page 204
5. Select move wpts to move the waypoints to a new or existing group, or 6. Select assign symbol to assign a new symbol to all the waypoints in the search results list. You can also select a waypoint from the list to view its details, or if accessed from the chart application set a goto or display t...
Page 205
Red racemark anti-clockwise red racemark clockwise marker restriction bottom mark top mark route start route end diver down diver down 2 oil rig filled circle fad (fish attracting device) concrete rubble seaweed oyster green can green nun red can red nun yellow can yellow nun fish trap brushpile pre...
Page 206
In the example above the day trip group will not be displayed in the chart application. 3. Select sort by: to switch between groups and symbols. A list of symbols or groups is displayed. 4. Select the group or symbol from the list that you want to show or hide. If show is displayed in the list then ...
Page 207
17.2 routes a route is a series of waypoints typically used to assist with passage planning and navigation. A route is displayed on screen as a series of waypoints linked by a line. D 11750-1 route features there are a range of route features for building, navigating and managing routes. The route f...
Page 208
11. Select exit to save the route and return to the chart application. Note: if you place a waypoint at the wrong position, select undo waypoint. Building a route using the waypoint list from the chart application: 1. Select menu. 2. Select navigate. 3. Select build route. The build route menu is di...
Page 209
Autorouting while building a route, the autorouting feature can be used to create the shortest route between 2 waypoints. Autorouting requires navionics ® updates, navionics ® platinum tm or navionics ® platinum tm + cartography. Autorouting can be used when creating new routes or when adding a rout...
Page 210
If the autorouting completes successfully the calculated route is displayed. Waypoints within the route that were calculated using autorouting are assigned the marker waypoint symbol. 5. Subsequent route legs can be added by selecting the next desired location on the chart. 6. When your route is com...
Page 211
3. Once the reason for the caution has been identified you can manipulate the route by moving the caution waypoints so that the caution area is avoided. Important: autorouting will not be used when moving waypoints within routes, extra care should be taken to ensure that the route leg and any moved ...
Page 212
Troubleshooting autorouting the information below details the warnings that can be displayed when using autorouting, a description of what the warning means and actions to be taken to correct the issue. Warning message description resolution autorouting has completed successfully the route maybe fol...
Page 213
Warning message description resolution the start and end point of the desired route are further than 100 nm apart. Create smaller route legs. E.G. Instead of trying to create a route from point a to point b, create a route from point a to point b to point c to point d, this will enable a route longe...
Page 214
1. Select my data. 2. Select import/export. 3. Select erase from system. 4. Select erase routes from system. The erase routes from system dialog is displayed. 5. Select erase all. The confirm delete dialog is displayed. 6. Select yes to confirm, or no to cancel the action. Route context menu placing...
Page 215
17.3 tracks a track is an on-screen trail that shows the passage you have taken. This trail is made up of a series of track points which are created automatically. You can save the track to create a permanent record of where you have been d 11754-2 with tracks you can: • review where you have been. ...
Page 216
• from the chart application, go to the following menu: menu > my data > tracks , and select the required track. • from the homescreen, select: my data > tracks and select the required track. You can then proceed and review or edit the required track using the options available. Renaming a track you...
Page 217
17.4 import and export waypoints, routes and tracks can be imported and exported using a memory card. For details on importing and exporting waypoints, routes and tracks refer to: 8.4 saving user data and user settings . 17.5 waypoints, routes and tracks storage capacity the display can store the fo...
Page 218
218 gs series.
Page 219
Chapter 18: chart application chapter contents • 18.1 chart application overview and features on page 220 • 18.2 electronic charts overview on page 222 • 18.3 navigation options on page 225 • 18.4 chart ranging and panning on page 227 • 18.5 chart selection on page 228 • 18.6 vessel position on the ...
Page 220
18.1 chart application overview and features the chart application provides route planning and navigation features. The chart application is pre-loaded with a lighthouse charts and navionics world base maps. Compatible electronic charts can be used to expand the information and detail regarding your...
Page 221
Note: raymarine recommends that you check the displayed vessel position in the chart application against your actual proximity to a known charted object. A typical gps has an accuracy of between 5 and 15 m. Chart context menu the chart context menu provides the cursors positional data and shortcuts ...
Page 222
18.2 electronic charts overview your multifunction display includes basic world base maps. Electronic charts provide additional cartographic information. The level of cartographic detail shown varies for different chart types, geographic locations and chart scales. The chart scale in use is indicate...
Page 223
1. Go to the lighthouse charts page of the raymarine website: http://www.Rayma- rine.Com/lighthousecharts/ . 2. Select either the raster or vector charts. The chart regions page is displayed. 3. Select your region. The chart region download page is displayed. 4. Click ‘view the terms of use’. 5. Rea...
Page 224
2. Right click on the file and select the extract here option from the zip options. 3. Once all files have been extracted select the chart files. 4. Right click and choose send to > removable disk the chart files will now be copied to your memory card. 5. Check that the files have been successfully ...
Page 225
6 * upload sonar logs and community edits to mobile device (wi-fi connection to mfd required) 7 ** upload sonar logs and community edits anonymously to navionics servers (internet connection required) note: * to participate in navionics sonar charts, sonar logging must be enabled on your mfd. Sonar ...
Page 226
Navigating to a location on the chart from the chart application: 1. Select the required location on-screen. The chart context menu is displayed. 2. Select goto cursor. Navigating to the cursor position on the chart using the menu d 11764-2 from the chart application: 1. Position the cursor at the d...
Page 227
• from a selected waypoint or any leg within a route. You can also follow any route in reverse order. Following a stored route from the chart application: 1. Select menu. 2. Select navigate. 3. Select follow route. The route list is displayed. 4. Select the route you want to follow. 5. Select follow...
Page 228
18.5 chart selection you can select the cartography type to be used in the chart application. The chart selection applies to the active chart instance. You must have the necessary cartography chart cards inserted into your multifunction display in order to display different cartography type. Selecti...
Page 229
18.7 chart orientation the orientation of a chart refers to the relationship between the chart and the direction that you are travelling in. Chart orientation is used in conjunction with motion mode to control how your vessel and chart relate to one another and how they are displayed on-screen. The ...
Page 230
18.8 chart motion mode the motion mode controls the relationship between the chart and your vessel. Whilst motion mode is active, as your vessel moves, the chart is redrawn to keep the vessel on-screen. The 3 motion modes are: • relative motion (default) • true motion • auto range. Note: in the 3d c...
Page 231
18.9 chart views if supported by your cartography type, the chart application can be set to either 2d or 3d view. Selecting 2d and 3d chart views you can switch between 2d and 3d views in the chart application if supported by your cartography. From the chart application menu: 1. Select presentation ...
Page 232
Item description 13 range out — use icon to range out (touchscreen displays only). 14 range in — use icon to range in (touchscreen displays only). Manipulating the 3d chart view from the chart application: 1. With the chart in 3d mode, go to the adjust viewing angle menu: menu > adjust viewing angle...
Page 233
18.10 chart display the chart display menu option determines the level of detail that is displayed on-screen. The chart display menu option is only available when using vector based cartography. The chart display options are shown below. Simple detailed extra detailed the level of detail shown on-sc...
Page 234
Enabling ais in the chart application to enable the ais overlay in the chart application follow the steps below. To enable the ais overlay your system must include an ais receiver or transceiver. The ais overlay is not available in 3d view. From the chart application menu: 1. Select presentation. 2....
Page 235
1. Select menu. 2. Select radar options or radar & ais options. Note: any changes made to the radar options from the chart application will be applied to the radar application. Chart scale and radar range synchronization you can synchronize the radar range in all radar windows with the chart scale. ...
Page 236
4. Select either tropical statements, marine warnings, marine zone forecasts, or watchbox warnings. Databoxes databoxes can be displayed in the application window. The databoxes can be switched on and off and the data that is displayed can be customized. Customizing databoxes in the chart applicatio...
Page 237
Community layer if supported by your cartography type, you can display user generated content (ugc) on the chart application. D13008-1 1 2 1. Community feature on. 2. Community feature off. To check if your navionics cartography supports community edits downloads please refer the navionics website: ...
Page 238
The rings are always centred on your vessel, and the scale varies to suit your current chart range. Each ring is labelled with the distance from your vessel. By default range rings are switched off. Range rings are not displayed in 3d view. Switching range rings on and off the range rings can be swi...
Page 239
Note: the fuel range ring is an estimated range that can be reached at the current rate of fuel consumption, of the fuel onboard and based on a number of external factors which could either extend or shorten the projected range. This estimate is based on data received from external fuel management d...
Page 240
18.12 chart vectors chart vectors are available for heading, cog, wind direction and tide direction. Chart vectors are only available in 2d view. A range of vector graphics can be displayed in the chart application when in 2d chart view. The following vectors can be independently enabled or disabled...
Page 241
18.13 cartography objects chart detail the chart detail setting determines the amount of detail shown in the chart application. Low high selecting the low option for the chart detail disables the following objects and overlays: • 2d shading • community edits • chart text • chart boundaries • light s...
Page 242
Cartography objects if supported by you cartography type, cartographic objects can be individually switched on and off. The table below show a list of these objects. The objects menu is accessed from: menu > presentation > objects. Note: the objects menu is only available when the cartography in use...
Page 243
Object (menu item) description options roads determines whether major coastal roads are displayed on the chart: • off — coastal roads are not displayed. • on — coastal roads are displayed. • off • on (default) additional wrecks determines whether extended information for new wrecks is displayed. • o...
Page 244
3. Select port (search by name) from the list. The on–screen keyboard is displayed. 4. Use the on-screen keyboard to enter the desired port name. 5. Select save. The search results are displayed. 6. Select the position against an entry in the list to reposition the cursor over that position. Display...
Page 245
Current graphs current graphs provide a graphical view of current activity. D 12309-1 1 4 5 2 9 6 1 0 3 8 7 1. Back — return to the previous menu or view. 2. Sunrise indicator — indicates when the sun rises. 3. Sunset indicator — indicates when the sun sets. 4. Exit — closes the dialog. 5. Nightfall...
Page 246
4. To set the animation date, select set date and then using the on screen keyboard enter the required date. 5. To set the animation date to the current date select today. 6. To set the animation date to 24 hours previous to the current date select previous day. 7. To set the animation date to 24 ho...
Page 247
18.15 depth & contour options if supported by your cartography type, the following depth and contour settings are available. Note: the menu items available are dependant upon your cartography type. The depth options are dependant upon the units of measure in use on your system. Menu item cartography...
Page 248
Menu item cartography type description options deep water color navionics determines the color of deep water. • white (default) • blue sonar logs navionics allows logging of depth and position data to your navionics chart card. This data will be sent to navionics to improve the contour detail of son...
Page 249
18.16 my data options the my data menu provides access to your user data. The options are found in the my data menu: menu > my data. • waypoints — view the waypoints group list. • routes — view the routes list. • tracks — view the tracks list. Refer to chapter 17 waypoints, routes and tracks for fur...
Page 250
18.18 measuring distances and bearings you can use the databar and context menu information you can use the measure function to measure distances in the chart application. You can determine the distance and bearing: • from your vessel to the position of the cursor; • between two points on the chart....
Page 251
Chapter 19: fishfinder application chapter contents • 19.1 fishfinder overview and features on page 252 • 19.2 sonar technologies on page 254 • 19.3 raymarine sonar modules on page 257 • 19.4 multiple sonar module support on page 257 • 19.5 sonar crosstalk interference on page 259 • 19.6 custom chan...
Page 252
19.1 fishfinder overview and features the fishfinder application uses a sonar module and a suitable sonar transducer. The sonar module interprets signals from the transducer and builds up a detailed underwater view. Various sonar technologies are available, all of which work on the same basic princi...
Page 253
The fishfinder window includes the following features: • the bottom together with any bottom structure such as reefs and shipwrecks etc. • target images indicating fish. • a status bar indicating the current sonar module and channel in use. • bottom depth. • * on-screen controls. Note: * on-screen c...
Page 254
19.2 sonar technologies traditional sonar technology traditional sonar uses a single carrier frequency or carrier wave for the sonar ping. The sonar works by measuring the time it takes the ping echo to return to the transducer to determine target depth. D12600-2 chirp technology chirp sonars use a ...
Page 255
Downvision tm is effective at lower vessel speeds. In deeper waters the chirp bandwidth is automatically optimized to improve bottom lock and the detection of moving objects (e.G. Fish) in the wider water column. The wide, thin beam produces clear target returns. The use of chirp processing and a hi...
Page 256
Interpreting sidevision™ images the following illustration shows how sidevision™ images on your multifunction display are related to the water column and sea floor to the sides of your vessel. Interpreting sidevision images sidevision™ images are constructed line-by-line, similar to the way a televi...
Page 257
19.3 raymarine sonar modules you can find details on raymarine’s sonar modules below. The depth shown below for downvision tm and the range for sidevision tm sonar modules are typical achievable depths / ranges, depending on the connected transducer in optimum water conditions. The depths shown for ...
Page 258
Channel description sonar module sidevision tm gives a clear view of fish and structure either side of your vessel. • cp200 sonar (200 khz chirp) targets bait and predator fish with wide sonar beam • cp100 • downvision tm variant mfds note: 1. The channels available are dependent on the sonar module...
Page 259
Depth data source where multiple sources of depth data exist on a system and the depth data source is set to auto the system will automatically select the optimum source for depth data. The system will set the data source for depth according to the priority table below: 1 st cp450c seatalk hs 2 nd c...
Page 260
Modules simultaneously in a raymarine system, it may not always be necessary to do so. If you are in a scenario that requires only one sonar module to be active at a time, disable any other sonar modules by changing the fishfinder application pane to a single one which only displays the output from ...
Page 261
19.6 custom channels when connected to an external traditional sonar module such as the cp300 or an external chirp sonar module such as the cp450c, custom channels can be created from the sonar module’s default channels; excluding auto channels. This enables some settings to be customized and saved ...
Page 262
19.7 the sonar image interpreting the bottom using sonar it is important to understand how to correctly interpret the bottom structure represented on-screen. The bottom usually produces a strong echo. The following images show how different bottom conditions are represented on-screen: d 6 8 5 5 -3 1...
Page 263
19.8 depth range the depth range function enables you to define the range of depth that you see in the fishfinder application. In auto range, the fishfinder application automatically adjusts the range to ensure the water column and bottom are always displayed. In manual range, you can adjust the ran...
Page 264
19.9 sidevision tm range the sidevision tm range function enables you to define the distance to the left and right of the vessel that is displayed on-screen. The range displayed on-screen can be adjusted to suit your needs. The table below shows examples of the sidevision tm range function. Sidevisi...
Page 265
19.11 fishfinder display modes selecting a display mode for the fishfinder application when using a legacy, traditional, chirp or downvision tm you can select which display mode you want to use. From the fishfinder application: 1. Select menu. 2. Select display mode. 3. Select select mode:. 4. Selec...
Page 266
Mode 1 mode 2 mode 3 the a-scope image is centred in the window. The left-hand side of the mode 1 image is expanded to give a more detailed view. The a-scope image angles outward as signal width increases with depth. The numbers displayed at the bottom when in a-scope mode indicate the approximate d...
Page 267
19.12 sidevision tm views when connected to a sidevision tm sonar module the default view displays both left (port) and right (starboard) views at the same time, the view icons and view menu can be used to switch between left and right views or both. View: both view: left view: right selecting a sid...
Page 268
19.13 presentation menu options the presentation menu provides access to features which provide additional on-screen detail. The table below shows the available presentation options. Menu item description options * target depth id controls whether the depth of identified targets are displayed. The l...
Page 269
19.14 depth and distance legacy, traditional chirp and downvision tm sonar modules use there respective transducers to obtain depth readings. Sidevision tm can only display depth readings when a separate source for depth is available on the network. The fishfinder application provides a number of fe...
Page 270
19.15 waypoints in the fishfinder application placing a waypoint in the fishfinder application enables you to mark a position so that you can return to it later. When a waypoint is placed its details are added to the waypoint list and a vertical line showing the waypoint symbol is displayed on-scree...
Page 271
Gain the gain settings alter the way the sonar module processes background noise. Adjusting the gain settings can improve the sonar image, however for optimum performance in most conditions, we recommend that you use the auto settings. The gain control determines the strength above which echoes are ...
Page 272
1. Select sensitivity settings. 2. Select auto gain mode. 3. Select the required auto gain mode. Color gain traditional, chirp and legacy sonar channels use different colors to determine the strength of an echo. You can adjust the color gain manually between 0% and 100% or set it to automatic. 20% m...
Page 273
0% tvg 30% tvg setting tvg to automatic the tvg setting can be set to automatic by following the steps below. From the fishfinder application: 1. Select menu. 2. Select sensitivity settings. 3. Select tvg. The tvg slider bar control is displayed. 4. Select auto so that a tick is placed in the auto b...
Page 274
3. When connected to external chirp sonar modules (excluding downvision tm ) and external traditional sonar modules (excluding legacy) you can select an auto tvg mode, noise filter the noise filter is available on downvision tm sonar modules. The noise filter reduces the amount of clutter displayed ...
Page 275
19.17 fishfinder alarms the following fishfinder alarms can be set when a depth data source is available. • fish — alarm sounds when a target meets the specified sensitivity level and, is within the depth limits (if enabled). • fishfinder deep — alarm sounds when the detected depth is greater than t...
Page 276
19.18 frequency tuning the frequency is dependent on the sonar module and transducer in use. When using a non-chirp sonar module or a chirp sonar module that is operating in non-chirp mode then the transducer’s frequency can be manually fine-tuned. The advantages of being able to tune the frequency ...
Page 277
19.19 sounder set-up menu options this section details the options available in the sounder set-up menu: (menu > set-up > sounder set-up). Menu item description options * ping rate hyper ping is a setting only available on traditional internal and legacy sonar modules, for use in shallow waters (dep...
Page 278
19.20 transducer set-up menu options the transducer set-up menu should be used when setting up your multifunction display for the first time or when installing a depth transducer. Note: the settings listed below will only be available if the connected transducer supports the data type. Menu item des...
Page 279
19.21 resetting the sonar the reset function restores the unit to its factory default values. Note: performing a factory reset will clear speed and temperature calibration settings and the depth offset. 1. Using a compatible raymarine multifunction display go to the fishfinder application page. 2. S...
Page 280
280 gs series.
Page 281
Chapter 20: data application chapter contents • 20.1 data application overview on page 282 • 20.2 selecting datapages using touch on page 284 • 20.3 selecting datapages on page 285 • 20.4 customizing the data application on page 285 • 20.5 list of data items on page 287 • 20.6 engine identification ...
Page 282
20.1 data application overview the data application enables you to view data generated by the multifunction display or data that is available on your system. Data can be obtained from devices connected using seatalk hs , seatalk ng or nmea protocols. Pre-configured datapages the default datapage con...
Page 283
Sailing page when the boat type has been configured as a sailing vessel, the sailing page is available in the data application. The sailing page includes compass and wind dials that displays various data designed specifically for sailing vessel. D13020-1 3 4 5 7 6 5 1 2 1. Compass dial 2. Wind dial ...
Page 284
4. Course correction indicator 5. Course correction details 20.2 selecting datapages using touch you can scroll through all available pages using the touchscreen. D12878-1 from the data application: 1. Touch the screen. 2. Slide your finger up and let go of the screen to go to the next datapage. 3. ...
Page 285
20.3 selecting datapages to select datapages using a non-touch multifunction display follow the steps below. From the data application: 1. Move the joystick down to goto the next page, or 2. Move the joystick up to goto the previous page. 20.4 customizing the data application you can customize the d...
Page 286
5. Select a data category. Selecting a data category will display a list of data items for that category. 6. Select the data item you want to display. Once selected a tick will be placed next to the data item in the menu and the cell on screen will display the new data item 7. Repeat steps 3 to 6 fo...
Page 287
20.5 list of data items categories of data available to display in the data application, databoxes, databar, and expanded databar are shown below. Dial graphics are not available in databoxes or databars. The following table shows the data items available by category. Data category description data ...
Page 288
Data category description data item data application graphics rpm rpm & sog coolant temperature coolant pressure oil temperature oil pressure oil pressure & coolant temperature transmission oil temperature transmission oil pressure transmission gear boost pressure fuel pressure fuel flow rate fuel f...
Page 289
Data category description data item data application graphics fuel level (%) total fuel (%) total fuel (vol) fuel flow total economy estimated fuel remaining distance to empty time to empty fuel used (trip) fuel** types of data related to the fuel system. For example, fuel levels. Fuel used (season)...
Page 290
Data category description data item data application graphics minimum water temperature maximum water temperature vessel position cog & sog cog sog maximum sog gps gps-related data. For example, vessel position. Average sog heading heading and speed (data application only.) locked heading locked hea...
Page 291
Data category description data item data application graphics waypoint info active waypoint name target position bearing to waypoint btw & dtw (data application only.) course made good cmg & dmg cmg & vmg (data application only.) distance to waypoint distance made good waypoint eta waypoint ttg rout...
Page 292
Data category description data item data application graphics fresh water (%) grey water (%) black water (%) tanks** data related to water tanks live well (%) local time time time-related data. For example, local time. Local date awa maximum awa minimum awa aws maximum aws minimum aws twa maximum tw...
Page 293
Data category description data item data application graphics awa & aws awa (ch) and aws awa and vmg twa & tws twa (ch) and tws twa and vmg gwd and beaufort gwd & gws none note: *dials and graphical representations are only available from the data application. Databar and data cell overlays can only...
Page 294
20.6 engine identification engine data can be displayed on your mfd using the data application, which provides some preset engine pages for displaying some of the most common types of engine data. Important: before you can display engine data on your mfd, you must: • ensure that your mfd is running ...
Page 295
Engine setup with an eci interface before you can display engine data on your mfd, you may need to use the "engine identification wizard” on the mfd to setup the engines. Important: when setting up on a multiple engine system, engines should always be turned on in sequence from port to starboard. Th...
Page 296
20.7 setting boat details you can change vessel settings from the data application menu. From the data application: 1. Select menu. 2. Select boat details. 3. Select num. Of engines, num. Of fuel tanks, or num. Of batteries. 4. Select either 1, 2, 3, 4 or 5. If the number of engines has been changed...
Page 297
20.9 color theme the color theme in the data application can be switched between light and dark. Dark theme (de- fault) light theme changing the color theme you can change the color theme by following the steps below. From the data application: 1. Select menu. 2. Select presentation. 3. Select color...
Page 298
20.10 units set-up you can specify your preference for the units of measurement that will be used in all applications. Menu item description options distance units the units of measure that will be used in all applications for the display of all values related to distance. • nautical miles • nm & m ...
Page 299
20.11 resetting minimum and maximum readings minimum and maximum readings sorted on the display can be reset from the data application. From the data application, with the data you want to reset displayed onscreen: 1. Select menu. 2. Select data resets. 3. Select the data item you want to reset. The...
Page 300
300 gs series.
Page 301
Chapter 21: radar application chapter contents • 21.1 radar application overview and features on page 302 • 21.2 multiple radar scanners on page 304 • 21.3 radar scanner status symbols on page 304 • 21.4 radar context menu on page 306 • 21.5 radar range and image quality on page 306 • 21.6 target tr...
Page 302
21.1 radar application overview and features radio detection and ranging (radar) is used to detect the presence, distance and speed of objects (known as ‘targets’). Radar works by transmitting radio pulses, then detecting reflections of these pulses (echoes) from objects in the area and displaying t...
Page 303
Radar application features depending on the connected radar scanner different options will be available. • radar features supports up to 2 radar scanners connected simultaneously. • 21.2 multiple radar scanners tracking targets. • 21.6 target tracking determining target distance, range and bearing. ...
Page 304
21.2 multiple radar scanners the multifunction display supports the use of up to 2 radar scanners on the same network. For each radar application you can select which radar scanner is displayed. 2 radar scanners can be displayed simultaneously by creating a dual splitscreen radar page on the homescr...
Page 305
2. Once the radar has powered up, select tx to start the radar transmitting. Putting the radar into standby the radar can be placed into standby mode, which allows the radar to remain powered up but not transmitting. With the radar transmitting, from the radar application: 1. Select menu. 2. Select ...
Page 306
21.4 radar context menu the radar application includes a context menu which provides positional data and menu items. The context menu provides the following positional data for the cursor location in relation to your vessel: • latitude • longitude • range • bearing the context menu also provide the ...
Page 307
D1641-5 1 3 2 4 5 6 item description 1 false echo 2 true echo 3 passing ship 4 mast or funnel 5 true echo 6 false echo multiple echoes multiple echoes are not very common but can occur if there is a large target with a wide vertical surface at a comparatively short range. The transmitted signal will...
Page 308
Interference when two or more radar-equipped vessels are operating within range of each other mutual radar interference can occur. This usually appears as a spiral of small dots from the display centre this type of interference is most noticeable at long ranges. This interference can be suppressed u...
Page 309
21.6 target tracking the guard zone , vrm/ebl and marpa functions will help you track targets and avoid collisions. With a radar connected to your multifunction display, you can: • assess how far away a target is and its bearing (vrm/ebl). • set an alarm to trigger when a target is within a specifie...
Page 310
1 3 2 4 d 12219-1 item description 1 safe target 2 lost target 3 dangerous target 4 target being acquired safety notices marpa can improve collision avoidance when used wisely. It is your responsibility to exercise common prudence and navigational judgement. There are conditions where acquiring a ta...
Page 311
4. Select vector length. 5. Select an appropriate time period. The distance that your vessel travels in the time period you specify here determines the length of the vector lines. 6. Select target history. 7. Select an appropriate time period. The target's previous position will be plotted on the ra...
Page 312
2. To display cpa graphics select cpa graphic from the context menu: i. Select auto to display the cpa graphic when the target is selected. Ii. Select on to display the cpa graphic while the target is being tracked. Iii. Select off to hide the cpa graphic. 3. To display course and bearing informatio...
Page 313
Item description 1. Cursor 2. Bearing and range from your vessel to the cursor position you can also display the cursor position in the databar, from the homescreen select: customize > databar set-up > edit databar, now select the data box where you want the cursor position to be displayed. Select n...
Page 314
Creating a vrm/ebl on the radar display from the radar application: 1. Select a target or location on screen. 2. Press the ok button. The radar context menu is displayed. 3. Select place vrm/ebl. 4. Using the joystick adjust the vrm/ebl to the required bearing and range. 5. Press the ok button to sa...
Page 315
21.8 radar mode and orientation radar orientation modes the radar can operate in a number of orientation modes to suit different types of navigation. The orientation of the radar refers to the relationship between the radar and the direction that you are travelling in. There are three orientation mo...
Page 316
2. Select presentation. 3. Select orientation & motion mode. 4. Select orientation. 5. Select the required orientation. Radar motion modes overview the motion mode controls the relationship between the radar and your vessel. There are two modes: • relative motion. • true motion. The selected motion ...
Page 317
21.9 radar presentation menu options function description options dual range this menu item allows you to turn dual range mode on and off. • on • off dual range channel this menu item allows you to choose long or short channel for dual range. • 1 • 2 orientation & motion mode this menu item contains...
Page 318
Function description options • 5 min • 10 min color palette this menu item allows you to select a color palette for the radar application. • bold • professional 1 • professional 2 • classic • night vision range rings this menu item allows you to turn the range rings on and off. • on • off safe zone ...
Page 319
1 target moving faster and in the same direction as vessel (wake appears towards your vessel’s heading). 2 ships heading marker. 3 target moving in opposite direction to vessel (wake appears opposite to your vessel’s heading). 4 target moving at approximately the same speed and direction as vessel (...
Page 320
21.10 radar tuning: on-screen gain controls touchscreen multifunction displays provide on-screen access to controls for gain, rain and sea clutter. Gain control rain control sea control note: non-touchscreen controls are accessed by the menu options: menu > rain and menu > adjust gain. Enabling and ...
Page 321
21.11 hd and superhd radar adjustments you can use the presets and other functions to improve the quality of the radar picture. The following settings are available from the radar menu and apply to hd radomes, hd and superhd open array scanners: menu item description options preset mode the radar ga...
Page 322
Selecting radar presets these presets require a hd or superhd radar scanner. Bird mode requires a superhd open array scanner with software version 3.23 or above or an hd radome. From the radar application menu: 1. Select preset mode. 2. Select buoy, harbor, costal, offshore, or bird as appropriate. ...
Page 323
21.12 non-hd digital radomes adjustments you can use the gain presets and other functions to improve the quality of the radar picture. The following settings apply to non-hd digital radomes and are available from the radar menu: menu item description options rain the radar scanner detects echoes fro...
Page 324
5. Select the auto box so that a tick is placed in the box for automatic ftc control. Adjusting radar anti sea clutter from the radar application menu, with the required preset mode selected: 1. Select adjust preset , where shall be the preset mode already selected. 2. Select sea: . 3. The sea clutt...
Page 325
21.13 dual range radar operation the dual range radar function enables you to view 2 ranges at the same time in separate windows. The function is available with superhd and hd radar scanners. Using your multifunction display and an hd or superhd radar scanner, you can view either a short or a long r...
Page 326
21.14 radar scan speed superhd open array radars with software version 3.23 or above or hd radomes support multiple scan speeds. Radar scan speed is set up using the radar set-up menu. When the system detects a scanner that is capable of operating at both 24 rpm and 48 rpm, 2 options are provided fo...
Page 327
21.15 radar set-up menu the radar set-up menu enables you to configure the performance and behavior of your radar scanner. Function description options timed transmit set-up this menu item contains a sub-menu that enables you to adjust the timed transmit options: • timed transmit • transmit period •...
Page 328
Function description options stc preset • 0 — 100% reset advanced • yes • no adjusting the radar tune control from the radar application: 1. Select menu. 2. Select radar set-up. 3. Select tune adjust. 4. Select tune adjust: . The tune adjust slider bar control is displayed. 5. Adjust the slider bar ...
Page 329
21.16 resetting the radar to reset radar settings to defaults follow the steps below: from in the radar application: 1. Select menu. 2. Select radar set-up. 3. Select advanced. 4. Select reset advanced. A confirmation pop up message is displayed. 5. Select yes to confirm reset. Radar application 329.
Page 330
330 gs series.
Page 331
Chapter 22: camera application chapter contents • 22.1 camera application overview and features on page 332 • 22.2 changing the camera feed on page 333 • 22.3 displaying multiple camera feeds using quad view on page 333 • 22.4 camera cycling on page 334 • 22.5 naming camera / video feeds on page 335...
Page 332
22.1 camera application overview and features analog and ip camera and video feeds can be viewed using the camera application. Analog feeds must be connected directly to the display, ip feeds must be available on the seatalk hs network. Ip camera feeds can be recorded and photos can be taken. D12881...
Page 333
22.2 changing the camera feed changing the camera / video feed on a new a series or new e series display, if more than 1 feed is available you can change which feed is displayed on the screen using touch. D 12598-1 from the camera application. 1. Touch and swipe your finger up to move to the next vi...
Page 334
3. Select the fullscreen feed. The quad view icon is displayed. 4. Select the quad view icon to switch the camera application back to quad view. 22.4 camera cycling when multiple feeds are available the camera application can be set up to automatically cycle through the available feeds at a specifie...
Page 335
Showing or hiding video input feeds during camera cycling by default your multifunction display’s video input(s) are shown during cycling, even if no feed is connected. You can choose to include or exclude video input(s) from camera cycling. The input(s) included or excluded will apply to both singl...
Page 336
22.6 adjusting the video image if supported by your connected camera / video input device or networked ip camera, you can adjust the image settings. With a video feed displayed in the camera application: 1. Select menu. 2. Select adjust. 3. Select contrast, brightness, or color, as appropriate. The ...
Page 337
22.8 selecting a location to store recordings in order to record, playback or capture a still image of ip camera feeds you must select the location you want to save to. If saving to a memory card ensure that a memory card with sufficient space is inserted into the relevant card reader slot. Note: do...
Page 338
3. Select stop. The file is saved and the video saved confirmation dialog is displayed. 4. Select ok to confirm, play to playback the recorded file or delete to delete the file. The confirmation dialog will automatically close after 5 seconds. Playing back a video file you can playback video clips u...
Page 339
22.10 taking photos when a camera feed from an ip camera is displayed you can capture a still image. Photos can be taken using the following methods: capture — immediate image capture. Timer — you can select the image to be taken in 5, 10 or 30 seconds after selection. Remote — you can use a wireles...
Page 340
Record icon stop recording icon take photo icon the onscreen icons will close after 5 seconds. Using the onscreen icons 1. Select the record icon to start recording. 2. Select the stop recording icon to stop the recording. 3. Select the take photo icon to capture a still image. 22.11 viewing photos ...
Page 341
Chapter 23: thermal camera application — pan and tilt cameras chapter contents • 23.1 thermal camera application overview on page 342 • 23.2 thermal camera image on page 342 • 23.3 controls overview on page 343 • 23.4 camera control on page 344 • 23.5 image adjustments on page 346 • 23.6 pan and til...
Page 342
23.1 thermal camera application overview the thermal camera application enables you to control a connected thermal camera and display its image on your multifunction display. Thermal imaging (also known as infrared) cameras enable you to see clearly in low-light and no-light conditions. For example,...
Page 343
Icon description scene preset mode for night docking. Scene preset mode for identifying people or objects in the water. Rear-view mode — image is flipped horizontally. Zoom setting: 2x zoom. Zoom setting: 4x zoom. Single active controller on network. Multiple active controllers on network. Pc / lapt...
Page 344
23.4 camera control power up and standby when the breaker connecting power to the camera is switched on, the camera will run a boot up sequence lasting for about 1 minute, after which the camera will be in standby mode. In order for the camera to operate, you must bring the camera out of standby mod...
Page 345
Pausing the thermal camera image with the thermal camera application displayed: 1. Select menu. 2. Select pause image. Thermal camera surveillance mode in surveillance mode the camera pans left and right continuously. The camera continues to pan until surveillance mode is disabled, or the camera con...
Page 346
Is now locked to the base. When you disable point mode, the unlock icon displays momentarily. The camera always starts up with point mode disabled. Enabling / disabling point mode point mode is disabled by default. With stabilization enabled you can also enable point mode at any time by following th...
Page 347
Note: if you have the disable color thermal video option selected in the camera's on-screen video setup menu, only 2 color modes are available — greyscale and red. Changing the thermal camera color mode with the thermal camera application displayed: 1. Select menu. 2. Select image options. 3. Use th...
Page 348
For details on how to select a target to ‘slew to’ refer to the radar and chart sections of your manual. The thermal camera can also automatically slew to: • mob target • dangerous ais target • dangerous marpa target options to enable or disable the automatic slew options are available in the therma...
Page 349
23.6 pan and tilt camera — new camera interface the thermal camera application menu options for a pan and tilt thermal camera with the new camera interface are shown below. Activate camera brings the thermal camera out of standby mode. (only available when camera is in standby.) pause image • on • o...
Page 350
• restore factory defaults • calibrate platform camera set-up menu set home position sets the camera’s current position as the camera home position. Slew settings provides automatic slew options and camera alignment settings. • auto slew to mob • auto slew to dangerous ais target • auto slew to dang...
Page 351
High power torque this option controls the amount of power used to hold the camera steady when in use. With the setting enabled the camera will consume more power, but will help ensure that the camera is held in place in rough seas. The high power torque mode may be useful for power boats that opera...
Page 352
23.7 high power and high torque modes camera state camera setting dual payload single payload standby • high power mode on • high torque mode on 22 w 17.4 w standby • high power mode off • high torque mode on 8 w 7.4 w standby • high power mode on • high torque mode off 13 w 13 w awake • high power ...
Page 353
23.8 pan and tilt camera — old camera interface the thermal camera application menu options for a pan and tilt thermal camera with the old camera interface are shown below. Activate camera brings the thermal camera out of standby mode. (only available when camera is in standby.) pause image • on • o...
Page 354
Osd menu options setup menus the setup menus provide a range of tools and settings to configure the thermal camera. The menus can be accessed from any controller on the system. The menus are overlaid onto the video image. Note: the on-screen menus only appear on the thermal camera image. They are no...
Page 355
Surveillance mode menu menu item / description settings / operation scan width this setting determines the distance that the camera pans left and right when in surveillance mode. Select from: • narrow — the camera will scan approximately 20º left and right of the center (40º total). • medium — the c...
Page 356
Camera state camera setting dual payload single payload awake • high power mode on or off • high torque mode on 30 w 19.4 w awake • high power mode on or off • high torque mode off 20 w 16.5 w user programmable button menu use this menu to set up the user button on the jcu. Menu item / description u...
Page 357
Chapter 24: thermal camera application — fixed mount cameras chapter contents • 24.1 thermal camera application overview on page 358 • 24.2 thermal camera image on page 358 • 24.3 controls overview on page 359 • 24.4 camera control on page 360 • 24.5 image adjustments on page 360 • 24.6 fixed mount ...
Page 358
24.1 thermal camera application overview the thermal camera application enables you to control a connected thermal camera and display its image on your multifunction display. Thermal imaging (also known as infrared) cameras enable you to see clearly in low-light and no-light conditions. For example,...
Page 359
Icon description rear-view mode — image is flipped horizontally. Zoom setting: 2x zoom. Zoom setting: 4x zoom. Single active controller on network. Multiple active controllers on network. Pc / laptop detected on network. Ffc (flat field correction) periodically the camera will perform a flat field c...
Page 360
24.4 camera control power up and standby when the breaker connecting power to the camera is switched on, the camera will run a boot up sequence lasting for about 1 minute, after which the camera will be in standby mode. In order for the camera to operate, you must bring the camera out of standby mod...
Page 361
Note: if you have the disable color thermal video option selected in the camera's on-screen video setup menu, only 2 color modes are available — greyscale and red. Changing the thermal camera color mode with the thermal camera application displayed: 1. Select menu. 2. Select image options. 3. Use th...
Page 362
24.6 fixed mount camera menu the thermal camera application menu options for a fixed mount thermal camera are shown below. Activate camera brings the thermal camera out of standby mode. (only available when camera is in standby.) pause image • on • off (default) image options select to display the i...
Page 363
Ball down mode this options should be enables when the camera is mounted upside down in the ‘ball down’ configuration. • on • off (default) high power standby this option controls the amount of power used to hold the camera in position while it is in standby mode. With the setting enabled the camera...
Page 364
364 gs series.
Page 365
Chapter 25: fusion link application chapter contents • 25.1 fusion link overview on page 366 • 25.2 media sources on page 367 • 25.3 browsing music on page 369 • 25.4 selecting shuffle and repeat functions on page 369 • 25.5 adjusting volume levels for each zone on page 370 • 25.6 selecting the zone...
Page 366
25.1 fusion link overview the multifunction display can control a connected 700 series fusion entertainment system. D12746-1 1 5 7 4 3 6 2 1 fusion menu options and track lists. 2 shuffle and repeat icons. 3 track / media specific details and controls. 4 zone volume control. 5 zone selector. 6 media...
Page 367
25.2 media sources the layout and controls available are determined by the selected media source. Ipod d12748-1 1 4 2 3 5 6 1 album artwork. 2 track title. 3 artist. 4 track progress. 5 track number. 6 album title. Menu options available for ipods are as follows: • browse music. • repeat. • shuffle....
Page 368
• tone controls. • select fusion system. Vhf d12753-1 1 3 2 1 squelch control. 2 channel. 3 manual / auto status. Menu options available for vhf radios are as follows: • preset. • scan. • tone controls. • select fusion system. Aux d12754-1 1 1 input gain. Menu options available for aux devices are a...
Page 369
25.3 browsing music you can browse the music available on your connected ipod or usb device. From the fusion link application: 1. Select the menu icon. 2. Select browse music. The media device name is displayed. 3. Select the media device. The contents of the device are displayed. 4. Browse the avai...
Page 370
25.5 adjusting volume levels for each zone the volume level for each zone can be adjusted individually or you can adjust all zones at the same time. From the fusion link application: 1. Select vol:. The zone volume control is displayed. 2. Select the relevant zone. 3. Adjust the volume level to the ...
Page 371
25.7 adjusting the tone controls the bass, middle, and treble tone controls can be adjusted. From the fusion link application: 1. Select the menu icon. 2. Select tone controls. 3. Select either bass, middle, or treble. 4. Adjust the level to the required setting. 5. Select back to go back to the men...
Page 372
25.9 menu options menu option media sources description browse music • ipod. • usb. Enables browsing of music stored on the device. Repeat • ipod. • usb. • off • folder — repeats all songs in the current folder. Shuffle • ipod. • usb. Switches track shuffle on and off. Tone controls • all devices. E...
Page 373
Chapter 26: weather application (north america only) chapter contents • 26.1 weather application overview on page 374 • 26.2 weather application set up on page 374 • 26.3 weather application display overview on page 375 • 26.4 weather map navigation on page 378 • 26.5 weather context menu on page 37...
Page 374
26.1 weather application overview the weather application overlays historical, live, and forecasted weather graphics on a world map. The weather application can only be used in north america and its coastal waters. The weather application graphics and their associated weather data enable you to dete...
Page 375
26.3 weather application display overview the weather application displays a range of graphics to indicate weather conditions and forecast information. The following diagram illustrates the main features of the weather application display: d 8564-4 5 7 1 0 6 9 8 1 2 3 4 1 1 1 1 item description 1 ra...
Page 376
Storm tracking symbols the weather application uses a range of symbols to represent different types of storm tracks. The storm tracking function enables you to monitor significant storms in the area. Examples of significant storms include tropical disturbances, depressions, storms and cyclones, hurr...
Page 377
Wave information symbols the weather application uses a range of graphics and symbols to represent different types of wave information. Symbol description wave height — waves are shown in 16 shades of color from: • reds — highest waves • greens — intermediate waves • blues — lowest waves wave period...
Page 378
26.4 weather map navigation you can move around the weather map and place waypoints. When you open the weather application, a world map is displayed. If the system has a position fix for your vessel, the map will be centred on your location. As in the chart application, use the cursor to move around...
Page 379
26.6 weather information you can view weather information for: • a specific location • a surface observation station (when displayed) • cities (when displayed) viewing weather data at a specific location you can view weather details at a particular location on the world map regardless of the display...
Page 380
26.7 weather reports you can view a number of different weather reports to give you a comprehensive view of the weather. Your multifunction display shows weather reports for: • tropical statements. • marine warnings. • marine zone forecasts. • watchbox warnings. Tropical statements tropical statemen...
Page 381
26.8 animated weather graphics you can view animated weather graphics to provide an indication of changing weather patterns. The animated weather option enables you to view an animation from the current time for: • nowrad — weather radar • wind • waves • pressure — surface pressure running a weather...
Page 382
Menu item description options control to zoom in and out. View report the view report menu allows you to view the different types of weather reports received. You can also select the location of the report. Report at • ship • cursor view report • tropical statements • marine warnings • marine zone f...
Page 383
26.10 glossary of weather terms term definition cold front the boundary between two different air masses where cold air pushes warm air out of the way and brings colder weather. Cyclone a large area of low atmospheric pressure, characterized by inward spiralling winds. A “low” also called a “depress...
Page 384
Term definition precipitation moisture that is released from the atmosphere as rain, drizzle, hail, sleet or snow, as well as dew and fog. Pressure centre a region of high or low pressure. Squall line a non-frontal band, or line, of thunderstorms. Super typhoon a typhoon that reaches maximum sustain...
Page 385
Chapter 27: sirius audio application (north america only) chapter contents • 27.1 sirius audio overview on page 386 sirius audio application (north america only) 385.
Page 386
27.1 sirius audio overview a connected, compatible raymarine sirius marine weather / satellite radio receiver can be controlled using the sirius audio application. Note: a sirius subscription is required to enable use of a sirius marine weather / satellite radio receiver. To enable volume controls t...
Page 387
Chapter 28: mobile applications chapter contents • 28.1 raymarine mobile apps on page 388 • 28.2 enabling wi-fi on page 389 • 28.3 enabling mobile apps on page 389 • 28.4 setting up wi-fi security on page 390 • 28.5 selecting a wi-fi channel on page 390 mobile applications 387.
Page 388
28.1 raymarine mobile apps raymarine mobile apps enable viewing and control of your multifunction display via a compatible mobile device, using a wi-fi connection. Raymarine currently offers the following mobile apps: • rayview • rayremote • raycontrol note: your multifunction display must have soft...
Page 389
28.2 enabling wi-fi with the homescreen displayed: 1. Select set-up. 2. Select system settings. 3. Select wireless connections. 4. Select wi-fi > on. 28.3 enabling mobile apps raymarine mobile apps must be enabled on your multifunction display before you can stream video or remote control your multi...
Page 390
28.4 setting up wi-fi security you can encrypt the wi-fi connection on the multifunction display to prevent unauthorized devices from accessing the connection. The default encryption is wpa2. With the homescreen displayed: 1. Select set-up. 2. Select system settings. 3. Select wireless connections. ...
Page 391
Chapter 29: maintaining your display chapter contents • 29.1 service and maintenance on page 392 • 29.2 product cleaning on page 392 maintaining your display 391.
Page 392
29.1 service and maintenance this product contains no user serviceable components. Please refer all maintenance and repair to authorized raymarine dealers. Unauthorized repair may affect your warranty. Routine equipment checks raymarine strongly recommends that you complete a number of routine check...
Page 393
Chapter 30: troubleshooting chapter contents • 30.1 troubleshooting on page 394 • 30.2 power up troubleshooting on page 395 • 30.3 radar troubleshooting on page 396 • 30.4 gps troubleshooting on page 397 • 30.5 troubleshooting autorouting on page 398 • 30.6 sonar troubleshooting on page 400 • 30.7 s...
Page 394
30.1 troubleshooting the troubleshooting information provides possible causes and corrective action required for common problems associated with marine electronics installations. All raymarine products are, prior to packing and shipping, subjected to comprehensive test and quality assurance programs...
Page 395
30.2 power up troubleshooting problems at power up and their possible causes and solutions are described here. Problem possible causes possible solutions check relevant fuses and breakers. Check that the power supply cable is sound and that all connections are tight and free from corrosion. The syst...
Page 396
30.3 radar troubleshooting problems with the radar and their possible causes and solutions are described here. Problem possible causes possible solutions check that the scanner power supply cable is sound and that all connections are tight and free from corrosion. Check relevant fuses and breakers. ...
Page 397
30.4 gps troubleshooting problems with the gps and their possible causes and solutions are described here. Problem possible causes possible solutions geographic location or prevailing conditions preventing satellite fix. Check periodically to see if a fix is obtained in better conditions or another ...
Page 398
30.5 troubleshooting autorouting the information below details the warnings that can be displayed when using autorouting, a description of what the warning means and actions to be taken to correct the issue. Warning message description resolution autorouting has completed successfully the route mayb...
Page 399
Warning message description resolution the start and end point of the desired route are further than 100 nm apart. Create smaller route legs. E.G. Instead of trying to create a route from point a to point b, create a route from point a to point b to point c to point d, this will enable a route longe...
Page 400
30.6 sonar troubleshooting problems with the sonar and their possible causes and solutions are described here. Problem possible causes possible solutions unit power supply fault. Check the unit power supply and cables. Other unit fault. Refer to the instructions supplied with the unit. Check that th...
Page 401
30.7 sonar crosstalk interference there are 2 types of potential sonar crosstalk interference in a raymarine sonar system: 1. Sidevision sonar crosstalk interference 2. Multiple sonar crosstalk interference the types of crosstalk interference that you may experience in your system depend on the comb...
Page 402
Note: due to physical size and other constraints that vary from vessel to vessel, it may not be possible to completely eliminate crosstalk interference from your system. However, this will not impede your ability to benefit from the full capabilities of your sonar system. Being able to easily identi...
Page 403
30.8 thermal camera troubleshooting problems with the thermal camera and their possible causes and solutions are described here. Problem possible causes possible solutions camera is in standby mode. The camera will not display video if it is in standby mode. Use the camera controls (either the therm...
Page 404
Problem possible causes possible solutions display brightness is set too low. Use the brightness controls at the display to adjust accordingly. The contrast or brightness settings in the thermal camera application are set too low. Use the appropriate menu in the thermal camera application to adjust ...
Page 405
30.9 system data troubleshooting aspects of the installation can cause problems with the data shared between connected equipment. Such problems, their possible causes and solutions are described here. Problem possible causes possible solutions check the data bus (e.G. Seatalk ng ) wiring and connect...
Page 406
30.10 video troubleshooting problems with the video inputs and their possible causes and solutions are described here. Problem possible causes possible solutions no signal message on screen (video image not displayed) cable or connection fault check that the connections are sound and free from corro...
Page 407
30.11 wi-fi troubleshooting aspects of the installation can cause problems with the data shared between wireless devices. Such problems, their possible causes and solutions are described here. Problem possible causes possible solutions ensure that wi-fi is enabled on the multifunction display (homes...
Page 408
30.12 bluetooth troubleshooting aspects of the installation can cause problems with the data shared between wireless devices. Such problems, their possible causes and solutions are described here. Problem possible causes possible solutions ensure that bluetooth is enabled on the multifunction displa...
Page 409
30.13 touchscreen troubleshooting problems with the touchscreen and their possible causes and solutions are described here. Problem possible causes possible solutions touch lock is enabled. Use the joystick to turn off the touch lock on the home screen. Screen is not being operated with bare fingers...
Page 410
30.14 miscellaneous troubleshooting miscellaneous problems and their possible causes and solutions are described here. Problem possible causes possible solutions check relevant fuses and breakers. Check that the power supply cable is sound and that all connections are tight and free from corrosion. ...
Page 411
Chapter 31: technical specification chapter contents • 31.1 technical specification on page 412 technical specification 411.
Page 412
31.1 technical specification physical specifications gs95 gs125 dimensions • width: 246.8 mm (9.7 in.) • height: 188.2 mm (7.4 in.) • depth (not including cables): 77 mm (3 in.) • depth (including cables): 198 mm (7.8 in.) • width: 311.8 mm (12.3 in.) • height: 237.1 mm (9.3 in.) • depth (not includ...
Page 413
Relative humidity maximum 75% waterproof rating ipx6 display specification gs95 gs125 size 9 in. 12.1 in. Type tft backlit led tft backlit led color depth 24–bit 24–bit resolution 800 x 480 pixels (wvga) 1280 x 800 pixels (wvga) aspect ratio 16:9 16:9 maximum allowable wrongly illuminated pixels 8 8...
Page 414
Electronic chart specification embedded electronic charts • lighthouse charts world base map. • navionics world base map. Compatible lighthouse charts • vector — lighthouse charts • raster — lighthouse charts compatible navionics chart cards • navionics ready to navigate • navionics silver • navioni...
Page 415
Chapter 32: technical support chapter contents • 32.1 raymarine customer support on page 416 • 32.2 learning resources on page 416 • 32.3 third-party support on page 417 technical support 415.
Page 416
32.1 raymarine customer support raymarine provides a comprehensive customer support service. You can contact customer support through the raymarine website, telephone and e-mail. If you are unable to resolve a problem, please use any of these facilities to obtain additional help. Web support please ...
Page 417
32.3 third-party support contact and support details for third-party suppliers can be found on the appropriate websites. Fusion www.Fusionelectronics.Com navionics www.Navionics.Com sirius www.Sirius.Com technical support 417.
Page 418
418 gs series.
Page 419
Chapter 33: spares and accessories chapter contents • 33.1 gs series accessories on page 420 • 33.2 gs series spares on page 420 • 33.3 network hardware on page 421 • 33.4 network cable connector types on page 421 • 33.5 raynet to raynet cables and connectors on page 422 • 33.6 network cable types o...
Page 420
33.1 gs series accessories the following accessories are available for gs series displays. Description part number rmk-9 remote keypad a80217 rcr-2 remote card reader a80218 5 m (16.4 ft gs series video out cable (hdmi) a80219 2 m 6.6 ft) gs series video in / alarm out cable a80235 1.5 m (4.9 ft) st...
Page 421
33.3 network hardware item part num- ber notes hs5 raynet network switch a80007 5–port switch for network connection of multiple devices featuring raynet connectors. Equipment with rj45 seatalk hs connectors can also be connected using suitable adapter cables. Rj45 seatalk hs network switch e55058 8...
Page 422
33.5 raynet to raynet cables and connectors d13160-1 4 2 3 1 a80161 a62361 a80005 a62362 a80006 400 mm (1.3 ft) 2 m (6.56 ft) 5 m (16.4 ft) 10 m (32.8 ft) 20 m (65.6 ft) a80162 100 mm (3.9 in) r70014 a80262 description typical use quantity 1 standard raynet connection cable with a raynet (female) so...
Page 423
Raynet to rj45 adapter cables d13158-1 1 2 3 4 5 a80160 400 mm (1.3 ft) a80151 3 m (9.84 ft) a80159 10 m (32.8 ft) a62360 1 m (3.28 ft) a80276 3 m (9.84 ft) a80272 400 mm (1.3 ft) a80247 100 mm (3.9 in) description typical use quantity 1 adapter cable with a raynet (female) socket on one end, and a ...
Page 424
33.6 network cable types there are 2 types of seatalk hs network cable — “patch” and “network”. • patch — for connecting the following devices to a raymarine network switch: – thermal camera via poe injector. – additional raymarine network switch. – pc or laptop using voyager planning software. • ne...
Page 425
33.8 seatalk ng cables and accessories seatalk ng cables and accessories for use with compatible products. Description part no notes seatalk ng starter kit t70134 includes: • 1 x 5 way connector (a06064) • 2 x backbone terminator (a06031) • 1 x 3 m (9.8 ft) spur cable (a06040) • 1 x power cable (a06...
Page 426
33.9 seatalk accessories seatalk cables and accessories for use with compatible products. Description part no notes 3–way seatalk junction box d244 1 m (3.28 ft) seatalk extension cable d284 3 m (9.8 ft) seatalk extension cable d285 5 m (16.4 ft) seatalk extension cable d286 9 m (29.5 ft) seatalk ex...
Page 427
Appendix a connectors and pinouts power, data, and video connector d12186-1 1 8 4 9 2 7 3 6 5 11 10 item remarks identification pwr / nmea / video connector type 11 pin twist-lock current source to network no current sourced for external devices current sink from network • psu: main power input. • n...
Page 428
Appendix b nmea 0183 sentences the display supports the following nmea 0183 sentences. These are applicable to nmea 0183 and seatalk protocols. Sentence description transmit receive aam waypoint arrival alarm sentence ● apb autopilot sentence ‘b’ ● ● bwc bearing and distance to waypoint ● ● bwr bear...
Page 429
Appendix c nmea 2000 sentences the display supports the following nmea 2000 sentences. These are applicable to nmea 2000, seatalk ng and seatalk 2 protocols. Message number message description transmit receive bridged to nmea 0183 59392 iso acknowledgment ● ● 59904 iso request ● ● 60928 iso address ...
Page 430
Message number message description transmit receive bridged to nmea 0183 129283 cross track error ● ● ● 129284 navigation data ● ● ● 129291 set and drift, rapid update ● ● ● 129301 time to or from mark ● 129539 gnss dops ● 129540 gnss sats in view ● ● 129542 gnss pseudorange noise statistics ● ● 129...
Page 431
Egr system throttle position sensor engine emergency stop mode warning level 1 warning level 2 power reduction maintenance needed engine comm error sub or secondary throttle neutral start protect engine shutting down unknown error nmea 2000 sentences 431.
Page 432
Appendix d switch panel application vessel control and monitoring systems when integrated with a vessel control and monitoring system your multifunction display can provide monitoring and controls for your power circuits, breakers, switches and equipment. The switch panel application can be used to:...
Page 433
1 3 5 2 4 6 d12739-1 1 toggle switch. 2 rotary (multi-state) switch. 3 position control switch. 4 momentary switch. 5 data item (dial gauge). 6 data item (tank level). Using the switches on a touchscreen this only applies to hybridtouch displays. From the switch panel application: 1. Toggle switch —...
Page 434
Appendix e software releases raymarine regularly updates its multifunction display software to introduce improvements, additional hardware support and user interface features. The table below details some of the important enhancements and which software revision they were introduced with. Software v...
Page 435
Software version applicable product manual multifunction displays compatibility changes • corrected (reversed) tvg control on cp450c to match all sonar modules • switch panel alarms can now be enabled/disabled globally across the network • added horizontal splitscreen template for 5.7 and 7 inch mfd...
Page 436
Appendix f multifunction display compatibility the table below identifies the mfd software version required to support the listed raymarine ® hardware. Cp450c v3.15 raymarine mobile applications v3.15 1kw transducer support for sonar variant displays v3.15 multiple thermal camera jcu’s v5.27 sirius ...
Page 438
Www.Raymarine.Com.