- DL manuals
- Raymarine
- GPS
- RS150
- Installation Instructions Manual
Raymarine RS150 Installation Instructions Manual
Summary of RS150
Page 1
Installation instructions rs150 gnss receiver © 2015 raymarine uk limited 87271-1 document number: 05-2016 date: english (en).
Page 3
Trademark and patents notice raymarine, tacktick, clear pulse, truzoom, hsb, seatalk, seatalk hs , seatalk ng , micronet, raytech, gear up, marine shield, seahawk, autohelm, automagic, and visionality are registered or claimed trademarks of raymarine belgium. Flir, downvision, sidevision, dragonfly,...
Page 5
Contents chapter 1 important information........................ 7 water ingress ............................................................ 7 disclaimer ................................................................. 7 suppression ferrites ................................................... 7 co...
Page 6
6 rs150 installation instructions.
Page 7
Chapter 1: important information warning: product installation and operation • this product must be installed and operated in accordance with the instructions provided. Failure to do so could result in personal injury, damage to your vessel and/or poor product performance. • raymarine recommends cer...
Page 8
Connections to other equipment requirement for ferrites on non-raymarine cables if your raymarine equipment is to be connected to other equipment using a cable not supplied by raymarine, a suppression ferrite must always be attached to the cable near the raymarine unit. Declaration of conformity ray...
Page 9
Chapter 2: document and product information chapter contents • 2.1 document information on page 10 • 2.2 rs150 product overview on page 10 document and product information 9.
Page 10
2.1 document information this document contains important information related to the installation of your raymarine product. The document includes information to help you: • plan your installation and ensure you have all the necessary equipment; • install and connect your product as part of a wider ...
Page 11
Chapter 3: planning the installation chapter contents • 3.1 installation checklist on page 12 • 3.2 parts supplied on page 12 • 3.3 software updates on page 13 • 3.4 tools required for installation on page 13 • 3.5 warnings and cautions on page 14 • 3.6 selecting a location on page 14 • 3.7 product ...
Page 12
3.1 installation checklist installation includes the following activities: installation task 1 plan your system. 2 obtain all required equipment and tools. 3 site all equipment. 4 route all cables. 5 drill cable and mounting holes. 6 make all connections into equipment. 7 secure all equipment in pla...
Page 13
3.3 software updates the software running on the product can be updated. • raymarine periodically releases software updates to improve product performance and add new features. • you can update the software for your product using a connected and compatible multifunction display. • refer to www.Rayma...
Page 14
3.5 warnings and cautions important: before proceeding, ensure that you have read and understood the warnings and cautions provided in the chapter 1 important information section of this document. 3.6 selecting a location warning: potential ignition source this product is not approved for use in haz...
Page 15
Between equipment and minimize the effect such interference could have on the performance of your system correct installation is required to ensure that emc performance is not compromised. Note: in areas of extreme emc interference, some slight interference may be noticed on the product. Where this ...
Page 16
16 rs150 installation instructions.
Page 17
Chapter 4: cables and connections chapter contents • 4.1 general cabling guidance on page 18 • 4.2 connections overview on page 18 • 4.3 seatalk ng® power supply on page 19 • 4.4 nmea 2000 network connection on page 21 • 4.5 seatalk ng® network example on page 21 cables and connections 17.
Page 18
4.1 general cabling guidance cable types and length it is important to use cables of the appropriate type and length • unless otherwise stated use only standard cables of the correct type, supplied by raymarine. • ensure that any non-raymarine cables are of the correct quality and gauge. For example...
Page 19
4.3 seatalk ng® power supply power is supplied to the product over the seatalk ng backbone. A seatalk ng backbone requires one 12 v dc power supply, connected to the seatalk ng backbone. This can be provided by: • a battery (1) , via the distribution panel, • an autopilot control unit (acu) (2) , • ...
Page 20
• you must fit a suitably rated fuse or breaker between the red wire and the battery’s positive terminal. • refer to the inline fuse ratings provided in the product’s documentation. • if you need to extend the length of the power cable, ensure you use suitably rated cable and that sufficient power (...
Page 21
4.4 nmea 2000 network connection your seatalk ng® device can be connected to a devicenet / nmea 2000 network. D12060-3 4 2 nmea 2000 3 seatalk ng device 1 1. Seatalk ng® device 2. Seatalk ng® to devicenet adaptor cable (a06045) 3. Devicenet t-piece 4. Nmea 2000 backbone 4.5 seatalk ng® network examp...
Page 22
22 rs150 installation instructions.
Page 23: Chapter 5: Installation
Chapter 5: installation chapter contents • 5.1 surface mounting on page 24 • 5.2 pole mounting on page 24 installation 23.
Page 24
5.1 surface mounting the unit can be mounted on a surface that is up to 28 mm (1.10 in) thick, approximately . To mount on a thicker surface longer studs will be required. D13546-1 1. Ensuring correct orientation, affix the supplied mounting template to the mounting surface at the desired location. ...
Page 25
Chapter 6: system checks and troubleshooting chapter contents • 6.1 initial test on page 26 • 6.2 troubleshooting on page 28 system checks and troubleshooting 25.
Page 26
6.1 initial test once the unit is fully connected and installed, perform an initial power on test to verify correct operation. Product type unit to use for verifying operation application(s) to use for verifying operation example screen mfd chart application (check the vessel position displayed on t...
Page 27
Accurate position. If in doubt, check the displayed vessel position in the chart application against your actual proximity to a known charted object. • estimated horizontal position error (ehpe) — ehpe is a measure of the estimated error of a position fix in the horizontal plane. The value displayed...
Page 28
6.2 troubleshooting the troubleshooting information provides possible causes and corrective action required for common problems associated with marine electronics installations. All raymarine products are, prior to packing and shipping, subjected to comprehensive test and quality assurance programs....
Page 29
Gnss troubleshooting problems with the gnss and their possible causes and solutions are described here. Problem possible causes possible solutions geographic location or prevailing conditions preventing satellite fix. Check periodically to see if a fix is obtained in better conditions or another geo...
Page 30
Led diagnostics led sequence led color status 15s 14.5s green • bus healthy, no communication bus faults • all sensors connected and ready 1s 0.5s green • sensors initializing 2s 1s green • gps initializing (can take up to 5 minutes at first use or after factory reset or software update) 4s 2s green...
Page 31: Chapter 7: Maintenance
Chapter 7: maintenance chapter contents • 7.1 service and maintenance on page 32 • 7.2 routine equipment checks on page 32 • 7.3 product cleaning on page 33 maintenance 31.
Page 32
7.1 service and maintenance this product contains no user serviceable components. Please refer all maintenance and repair to authorized raymarine dealers. Unauthorized repair may affect your warranty. 7.2 routine equipment checks raymarine strongly recommends that you complete a number of routine ch...
Page 33
7.3 product cleaning best cleaning practices. When cleaning products: • if your product includes a display screen, do not wipe the screen with a dry cloth, as this could scratch the screen coating. • do not use abrasive, or acid or ammonia based products. • do not use a jet wash. Maintenance 33.
Page 34
34 rs150 installation instructions.
Page 35
Chapter 8: technical support chapter contents • 8.1 raymarine product support and servicing on page 36 • 8.2 learning resources on page 37 technical support 35.
Page 36
8.1 raymarine product support and servicing raymarine provides a comprehensive product support service, as well as warranty, service, and repairs. You can access these services through the raymarine website, telephone, and e-mail. Product information if you need to request service or support, please...
Page 37
8.2 learning resources raymarine has produced a range of learning resources to help you get the most out of your products. Video tutorials raymarine official channel on youtube: • http://www.Youtube.Com/u- ser/raymarineinc video gallery: • http://www.Rayma- rine.Co.Uk/view/?Id=2679 product support v...
Page 38
38 rs150 installation instructions.
Page 39
Chapter 9: technical specification chapter contents • 9.1 technical specification on page 40 technical specification 39.
Page 40
9.1 technical specification nominal supply voltage 12 v dc (supplied by seatalk ng ) operating voltage range 9 v dc to 16 v dc (protected up to 32 v dc) power consumption 30 ma max. Environmental installation environment • operating temperature: -25 ºc to +55 ºc (-13 ºf to 131 ºf) • storage temperat...
Page 41
Chapter 10: spares and accessories chapter contents • 10.1 accessories on page 42 • 10.2 seatalk ng® cabling components on page 42 • 10.3 seatalk ng® cables and accessories on page 43 spares and accessories 41.
Page 42
10.1 accessories the following accessories are available for the rs150. Accessories item part number pole mount adaptor kit a80370 6 m seatalkng white spur cable a06072 10.2 seatalk ng® cabling components seatalk ng cabling components and their purposes. Connection / cable notes backbone cable (vari...
Page 43
10.3 seatalk ng® cables and accessories seatalk ng cables and accessories for use with compatible products. Description part no notes seatalk ng starter kit t70134 includes: • 1 x 5 way connector (a06064) • 2 x backbone terminator (a06031) • 1 x 3 m (9.8 ft) spur cable (a06040) • 1 x power cable (a0...
Page 44
44 rs150 installation instructions.
Page 45
Appendix a nmea 2000 pgn support the unit supports the following nmea 2000 pgns. Pgn description transmit (tx) receive (rx) 59904 iso request ● 59932 iso acknowl- edgement ● 60928 iso address claim ● ● 65240 iso commanded address ● 12620 8 nmea - request group function ● 12620 8 nmea - command group...
Page 46
46 rs150 installation instructions.
Page 48
Www.Raymarine.Com raymarine uk limited, marine house, cartwright drive, fareham, po15 5rj. United kingdom. Tel: +44 (0)1329 246 700