Contents preparation . . . . . . . . . . . . . . . .1-2 assembly . . . . . . . . . . . . . . . . . . 3 installation . . . . . . . . . . . . . . . 4-11 install the door control . . . . . . 12-13 install the protector system ® . . 14-17 power. . . . . . . . . . . . . . . . . . 18-19 adjustments . . . ...
1 safety symbol and signal word review this garage door opener has been designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the instructions and warnings contained in this manual. When you see these safety symbols and signal w...
2 carton inventory accessories will vary depending on the garage door opener model purchased. Depending on your specific model, other accessories may be included with your garage door opener. The instructions for these accessories will be attached to the accessory and are not included in this manual...
3 assembly 1 attach the rail to the garage door opener to avoid possible serious injury to finger from moving garage door opener: l always keep hand clear of sprocket while operating opener. L securely attach sprocket cover before operating. To avoid serious damage to garage door opener, use only th...
4 installation important installation instructions warning to reduce the risk of severe injury or death: 1. Read and follow all installation warnings and instructions. 2. Install garage door opener only on properly balanced and lubricated garage door. An improperly balanced door may not reverse when...
5 installation 1 determine the header bracket location to prevent possible serious injury or death: l header bracket must be rigidly fastened to structural support on header wall or ceiling, otherwise garage door might not reverse when required. Do not install header bracket over drywall. L concrete...
6 installation 2 install the header bracket you can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use co...
7 installation 3 attach the rail to the header bracket 1. Align the rail with the header bracket. Insert the clevis pin through the holes in the header bracket and rail. Secure with the ring fastener. Note: use the packing material as a protective base for the garage door opener. Hardware clevis pin...
8 installation 5 hang the garage door opener to avoid possible serious injury from a falling garage door opener, fasten it securely to structural supports of the garage. Concrete anchors must be used if installing any brackets into masonry. Hanging your garage door opener will vary depending on your...
9 installation 6 install the light bulbs to prevent possible overheating of the endpanel or light socket: l do not use short neck or specialty light bulbs. L do not use halogen bulbs. Use only incandescent. To prevent damage to the opener: l do not use bulbs larger than 100w. L only use a19 size bul...
10 installation 8 install the door bracket fiberglass, aluminum or lightweight steel garage doors will require reinforcement before installation of door bracket. Contact the garage door manufacturer or installing dealer for opener reinforcement instructions or reinforcement kit. Failure to reinforce...
11 installation 9 connect the door arm to the trolley important: the groove on the straight door arm must face away from the curved door arm. 1. Close the door. Disconnect the trolley by pulling the emergency release handle. Slide the outer trolley back (away from the door) about 2" (5 cm). 2. Attac...
12 install the door control 1 install the door control to prevent possible serious injury or death from electrocution: l be sure power is not connected before installing door control. L connect only to 12 volt low voltage wires. To prevent possible serious injury or death from a closing garage door:...
13 install the door control 2 wire the door control to the garage door opener hardware insulated staple (not shown) pre-wired installations: when wiring the door control to the garage door opener make sure you use the same wires that are connected to the door control. 1. Run the white and red/white ...
14 install the protector system ® introduction be sure power is not connected to the garage door opener before installing the safety reversing sensor. To prevent serious injury or death from closing garage door: l correctly connect and align the safety reversing sensor. This required safety device m...
15 install the protector system ® 1 install the safety reversing sensors hardware carriage bolt 1/4"-20x1/2" wing nut 1/4"-20 the safety reversing sensors can be attached to the door track, the wall, or the floor. If the door track will not support the sensor bracket a wall installation is recommend...
16 install the protector system ® option c floor installation use an extension bracket (not provided) or wood block to raise the sensor bracket if needed. 1. Carefully measure the position of both sensor brackets so they will be the same distance from the wall and unobstructed. 2. Attach the sensor ...
17 install the protector system ® option b pre-wired installation 1. Cut the end of the safety reversing sensor wire, making sure there is enough wire to reach the pre-installed wires from the wall. 2. Separate the safety reversing sensor wires and strip 7/16 inch (11 mm) of insulation from each end...
18 power 1 connect power to prevent possible serious injury or death from electrocution or fire: l be sure power is not connected to the opener, and disconnect power to circuit before removing cover to establish permanent wiring connection. L garage door installation and wiring must be in compliance...
19 power 2 ensure the safety reversing sensors are aligned the door will not close if the sensors have not been installed and aligned correctly. When the light beam is obstructed or misaligned while the door is closing, the door will reverse and the garage door opener lights will flash ten times. If...
20 adjustments introduction without a properly installed safety reversal system, persons (particularly small children) could be seriously injured or killed by a closing garage door. L incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system. L ...
21 adjustments 1 program the travel without a properly installed safety reversal system, persons (particularly small children) could be seriously injured or killed by a closing garage door. L incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal sy...
22 adjustments 2 test the safety reversal system without a properly installed safety reversal system, persons (particularly small children) could be seriously injured or killed by a closing garage door. L safety reversal system must be tested every month. L after any adjustments are made, the safety...
23 important safety instructions warning to reduce the risk of severe injury or death: 1. Read and follow all warnings and instructions. 2. Always keep remote controls out of reach of children. Never permit children to operate or play with garage door control push buttons or remote controls. 3. Only...
24 operation features your garage door opener is equipped with features to provide you with greater control over your garage door operation. Alert2close the alert2close feature provides a visual and an audible alert that an unattended door is closing. Timer-to-close (ttc) the ttc feature automatical...
25 operation using the door control synchronize the door control to synchronize the door control to the garage door opener, press the push bar until the garage door opener activates (it may take up to 3 presses). Test the door control by pressing the push bar, each press of the push bar will activat...
26 door control control panel setup lock note: your remote controls will not work when lock mode is active however your keyless entry will still allow access to your garage. Activate: press and hold the lock button for 2 seconds. The command led will flash as long as the lock feature is activated an...
27 operation remote control your remote control has been programmed at the factory to operate with your garage door opener. Older raynor remote controls are not compatible, see page 32 for compatible accessories. Programming can be done through the door control or the learn button the garage door op...
28 operation to open the door manually to prevent possible serious injury or death from a falling garage door: l if possible, use emergency release handle to disengage trolley only when garage door is closed. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/...
29 maintenance maintenance schedule every month l manually operate door. If it is unbalanced or binding, call a trained door systems technician. L check to be sure door opens and closes fully. Adjust if necessary, see page 21. L test the safety reversal system. Adjust if necessary, see page 22. Ever...
30 diagnostic chart your garage door opener is programmed with self-diagnostic capabilities. The up and down arrows on the garage door opener flash the diagnostic codes. Diagnostic code symptom solution up arrow flash(es) down arrow flash(es) 1 1 the garage door opener will not close and the light b...
31 diagnostic code symptom solution up arrow flash (es) down arrow flash(es) 4 1-4 door is moving stops and or reverses. Manually open and close the door. Check for binding or obstructions, such as a broken spring or door lock, correct as needed. If the door is binding or sticking contact a trained ...
32 880rgd smart control panel ® : displays temperature, time and system diagnostics; includes a push bar to open and close the door and a lock feature for extra security. Security+ 2.0™ compatible. 990lm surge protector: the garage door opener surge protector is designed to protect raynor ® garage d...
Warranty raynor one-year limited warranty four-year motor limited warranty raynor ® (“seller”) warrants to the first retail purchaser of this product, for the residence in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of one year...
5 1 4 3 2 description part number 1 master link kit 4a1008 2 chain pulley bracket 41a4813 3 complete trolley assembly 41a3489 4 one-piece rail - 7’ (2.1 m) 1707lm one-piece rail - 8’ (2.4 m) 1708lm one-piece rail - 10’ (3 m) 1710lm 5 full chain assembly 41d3484 not shown rail grease 83a11-2 11 5 8 7...
1 2 3 10 12 13 8 7 6 4 5 11 9 garage door opener parts © 2015, the chamberlain group, inc. 114a4724b all rights reserved description part number 1 sprocket cover with screws 31d380 2 gear and sprocket 41c4220a 3 drive and worm gear 41a2817 4 front end panel with all labels 41a5484-1 5 light socket 0...
