Contents preparation . . . . . . . . . . . . . . . .2-3 assembly . . . . . . . . . . . . . . . . .4-5 installation . . . . . . . . . . . . . . . 6-13 install the door control . . . . . . 14-16 install the protector system ® . . 17-20 power. . . . . . . . . . . . . . . . . . 21-22 adjustments . . . ....
2 safety symbol and signal word review this garage door opener has been designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the instructions and warnings contained in this manual. When you see these safety symbols and signal w...
3 a b c k j i p d e f h g l m n overview/carton inventory garage door opener assembly a. T e k c a r b r e d a e h b. Pulley and bracket c. T e k c a r b r o o d d. M r a r o o d d e v r u c e. M r a r o o d t h g i a r t s f. Y e ll o r t g. Emergency release rope and handle h. Rail i. R e n e p o ...
4 to avoid serious damage to garage door opener, use only those bolts/fasteners mounted in the top of the opener. Washered bolt 5/16"-18x1/2" (mounted in the garage door opener) hardware lock nut (mounted in the garage door opener) note: only use the bolts removed from the garage door opener. Place ...
5 2 attach the chassis support bracket to avoid possible serious injury to finger from moving garage door opener: • always keep hand clear of sprocket while operating opener. • securely attach sprocket cover before operating. 2.1 position the chassis support bracket on the unit. 2.2 attach the brack...
6 important installation instructions warning to reduce the risk of severe injury or death: 1. Read and follow all installation warnings and instructions. 2. Install garage door opener only on properly balanced and lubricated garage door. An improperly balanced door may not reverse when required and...
7 to prevent possible serious injury or death: • header bracket must be rigidly fastened to structural support on header wall or ceiling, otherwise garage door might not reverse when required. Do not install header bracket over drywall. • concrete anchors must be used if mounting header bracket or 2...
8 you can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided). Hardware la...
9 3.1 align the rail with the header bracket. Insert the clevis pin through the holes in the header bracket and rail. Secure with the ring fastener. Note: use the packing material as a protective base for the garage door opener. Ring fastener clevis pin 5/16" x 2-3/4" hardware clevis pin 5/16" x 2-3...
10 to avoid possible serious injury from a falling garage door opener, fasten it securely to structural supports of the garage. Concrete anchors must be used if installing any brackets into masonry. Hardware hex bolt 5/16"- 18x7/8" nut 5/16"-18 lock washer 5/16" hanging your garage door opener will ...
11 to prevent possible overheating of the end panel or light socket: • use only a19 incandescent (100w maximum) or compact fluorescent (26w maximum) light bulbs. • do not use incandescent bulbs larger than 100w. • do not use compact fluorescent light bulbs larger than 26w (100w equivalent). To preve...
12 fiberglass, aluminum or lightweight steel garage doors will require reinforcement before installation of door bracket. Contact your door manufacturer for reinforcement kit. Figure 1 shows one piece of angle iron as the horizontal brace. For the vertical brace, 2 pieces of angle iron are used to c...
13 important: the groove on the straight door arm must face away from the curved door arm. Straight door arm curved door arm (groove facing out) correct incorrect straight door arm curved door arm 9.1 close the door. Disconnect the trolley by pulling the emergency release handle. Slide the outer tro...
14 1 install the door control install the door control to prevent possible serious injury or death from electrocution: • be sure power is not connected before installing door control. • connect only to 12 volt low voltage wires. To prevent possible serious injury or death from a closing garage door:...
15 install the door control 1.5 position the bottom hole of the door control over the screw and slide down into place. 1.6 lift the push bar up and mark the top hole. 1.7 remove the door control from the wall and drill a 5/32 inch (4 mm) hole for the top screw. 1.8 position the bottom hole of the do...
16 install the door control 3 attach the warning labels 3.1 attach the entrapment warning label on the wall near the door control with tacks or staples. 3.2 attach the manual release/safety reverse test label in a visible location on the inside of the garage door..
17 introduction be sure power is not connected to the garage door opener before installing the safety reversing sensor. To prevent serious injury or death from closing garage door: • correctly connect and align the safety reversing sensor. This required safety device must not be disabled. • install ...
Install the protector system ® 1 install the safety reversing sensors the safety reversing sensors can be attached to the door track, the wall, or the floor. If the door track will not support the sensor bracket a wall installation is recommended. Choose one of the following installations. Hardware ...
Install the protector system ® 1 install the safety reversing sensors option c floor installation use an extension bracket or wood block to raise the sensor bracket if needed. 1.1c carefully measure the position of both sensor brackets so they will be the same distance from the wall and unobstructed...
Install the protector system ® option b pre-wired installation 2.1b cut the end of the safety reversing sensor wire, making sure there is enough wire to reach the pre-installed wires from the wall. 2.2b separate the safety reversing sensor wires and strip 7/16 inch (11 mm) of insulation from each en...
21 1 connect power to prevent possible serious injury or death from electrocution or fire: • be sure power is not connected to the opener, and disconnect power to circuit before removing cover to establish permanent wiring connection. • garage door installation and wiring must be in compliance with ...
22 2 ensure the safety reversing sensors are aligned the door will not close if the sensors have not been installed and aligned correctly. When the light beam is obstructed or misaligned while the door is closing, the door will reverse and the garage door opener lights will flash ten times. If the d...
23 without a properly installed safety reversal system, persons (particularly small children) could be seriously injured or killed by a closing garage door. • incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system. • after any adjustments are...
24 1 program the travel without a properly installed safety reversal system, persons (particularly small children) could be seriously injured or killed by a closing garage door. • incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system. • afte...
25 2 test the safety reversal system without a properly installed safety reversal system, persons (particularly small children) could be seriously injured or killed by a closing garage door. • safety reversal system must be tested every month. • after any adjustments are made, the safety reversal sy...
26 important safety instructions warning to reduce the risk of severe injury or death: 1. Read and follow all warnings and instructions. 2. Always keep remote controls out of reach of children. Never permit children to operate or play with garage door control push buttons or remote controls. 3. Only...
27 your garage door opener is equipped with features to provide you with greater control over your garage door operation. Alert2close the alert2close feature provides a visual and an audible alert that an unattended door is closing. Timer-to-close (ttc) the ttc feature automatically closes the door ...
28 using the door control synchronize the door control to synchronize the door control to the garage door opener, press the push bar until the garage door opener activates (it may take up to 3 presses). Test the door control by pressing the push bar, each press of the push bar will activate the gara...
29 smart control panel setup the features on the door control can be programmed through a series of menus on the screen and the navigation buttons. Refer to the descriptions below. Screen the main screen displays the time, temperature, and current battery charge (if applicable). Navigation buttons f...
30 your remote control has been programmed at the factory to operate with your garage door opener. Older raynor remote controls are not compatible, see page 35 for compatible accessories. Programming can be done through the door control or the learn button the garage door opener. To program addition...
31 to erase the memory erase all remote controls and keyless entries 1 press and hold the learn button on garage door opener until the learn led goes out (approximately 6 seconds). All remote control and keyless entry codes are now erased. Reprogram any accessory you wish to use. Erase all devices (...
32 to prevent possible serious injury or death from a falling garage door: • if possible, use emergency release handle to disengage trolley only when garage door is closed. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly. • never use emergen...
33 diagnostic chart your garage door opener is programmed with self-diagnostic capabilities. The up and down arrows on the garage door opener flash the diagnostic codes. Diagnostic code symptom solution up arrow flash(es) down arrow flash(es) 1 1 the garage door opener will not close and the light b...
34 diagnostic code symptom solution up arrow flash(es) down arrow flash(es) 4 1-4 door is moving stops and or reverses. Manually open and close the door. Check for binding or obstructions, such as a broken spring or door lock, correct as needed. If the door is binding or sticking contact a trained d...
35 accessories security✚ 2.0™ wireless door control: push bar, light feature and auxiliary button. Includes battery. Garage and gate monitor: monitor open/closed status for up to 4 myq ® compatible garage door openers or gate operators and close them from anywhere in the home. Remote light control: ...
Warranty raynor ® five-year limited warranty lifetime motor limited warranty raynor ® (“seller”) warrants to the fi rst retail purchaser of this product, for the residence in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of fi ve...
37 repair parts rail assembly parts installation parts 1 3 4 5 6 2 description part number 1 chain - for 7 foot door 41d3484 chain - for 8 foot door 41d3483 chain - for 10 foot door 41d3485 2 chain pulley bracket 41a2780 3 master link 4a1008 4 one-piece rail 7 feet (2.1 m) 3707ch one-piece rail 8 fe...
38 6 1 5 11 10 2 12 13 14 7 7 8 8 9 3 4 repair parts garage door opener parts - ultra ii description part number 1 chassis support bracket assembly kit 041c5069 2 chain spreader 041a4208-2 3 gear and sprocket 041a5658-1 4 drive and worm gear 041a2817 5 gear case 041a5532 6 front end panel 041a7756 7...
39 notes.
© 2015, the chamberlain group, inc. 114a4621c all rights reserved.
