Installation & operating instructions swimming pool & spa heater d-2 catalog no. 6000.57.1d effective: 05-21-10 replaces: 10-26-06 p/n 241243 rev. 3 warning: if these instructions are not followed exactly, a fire or explosion may result causing property damage, personal injury or death. Do not store...
2 rev. 3 reflects the following: changes to: parts photos on page 3, dimensional illustration on page 4, fig. 1 and fig. 3 on page 5, illustrated parts list on page 19.
3 receiving equipment on receipt of your equipment, it is suggested that you visually check for external damage to the carton. If the carton is damaged, it is suggested that a note be made on the bill of lading when signing for equipment. Remove the complete assembly from the carton. If it is damage...
4 installation requirements failure to install, maintain and/or operate the power vent in accordance with manufacturerʼs instructions may result in conditions which can produce bodily injury and property damage. The equipment must be installed by a qualified installer in accordance with all local co...
5 installation 1. Start off by disconnecting main power to the heater. 2. Remove the front door from the heater. See fig 1. 3. If this is a retro-fit application, remove existing “pagoda top” and discard. See fig. 2. If equipped with a drafthood, refer to drafthood installation manual for removal pr...
6 installation (continued) 6. Lower the jacket top back onto the heater and reinstall the (6) phillips screws. See fig. 3. 7. If installing on a model 266, 267, 406 or 407 heater, skip step 8. 8. Turn the power vent upside down. Using a 5/16” nut driver, relocate the mounting brackets as shown in fi...
7 installation (continued) 13. Install the right side outdoor conduit through the top 7/8” hole located on the right side of the heater. See. Fig. 13. Note: you must first remove the 7/8” plug on the heater to install the hard conduit. 14. Wire the heater power lines along with the d-2 power vent po...
8 installation (continued) 19. Route the 24 vac harness through the 7/8” grommet, see fig. 17. 20. Continue to route the harness down through any available grommet hole. See fig. 18. 21. Wire the harness along with the installed gas valve harness per the wiring diagram. 22. Reinstall the (4) phillip...
9 u.S. Installations 1 canadian installations 2 a clearance above grade, veranda, porch, deck, or balcony 1 ft (30 cm) 1 ft (30 cm) b clearance to window or door that may be opened 4 ft (1.2m) below or to side of opening; 1 foot (30 cm) above opening 3 ft (91 cm) c clearance to permanently closed wi...
10 venting (continued).
11 venting (continued).
12 venting (continued).
13 venting (continued).
14 sequence of operation on call for heat, the pc board will go through its safety chain (water pressure switch, high limit 1 & 2, roll-out, etc.). When the safety chain is closed, the iid pilot will begin to spark and the pilot gas valve will open. A flame will be lit at the pilot assembly. When an...
15 wiring (continued) step 1 : verify current connections as shown below. P/pv c/ m/mv mv pv r/bk y/bk y/bk v/bk v/bk v/ bk y/ bk g /b k p4 1 relay d-2 power vent y/ bk honeywell valve y/ bk v/ w v/ bk honeywell valve pv mv m/mv c/ p/pv step 2 : disconnect both terminals mvpv & mv as shown below. D-...
16 wiring (continued) models 206, 266, 336, 406 equipped with honeywell gas valve v/w v/ bk v/ bk g /b k r/bk 1 p4 d-2 power vent p/pv c/ m/mv mv pv honeywell valve step 4 : connect the main valve line, female spade to male spade as shown below. D-2 power vent v/ bk y/ bk v/w v/bk r/bk p4 1 g /b k s...
17 wiring diagram – models 207a, 267a, 337a, 407a po w er ve nt d- 2 d- 2 bl o w er po w er ve nt g as va lv e ho ne yw el l 1 1 + -.
18 wiring diagram – models 206a, 266a, 336a, 406a po w er ve nt d- 2 d- 2 bl o w er po w er ve nt + - 1 1 th tr.
19 replacement parts note: to supply you with the correct part, it is impor- tant that you supply the heater model number, serial number and type of gas when applicable. Any part returned for replacement under standard company warranties must be properly tagged with a return parts tag, completely fi...
20 www.Raypak.Com raypak, inc., 2151 eastman avenue, oxnard, ca 93030 (805) 278-5300 fax (805) 278-5468 litho in u.S.A..
