Ritetemp 8030 Install Manual
Install guide 8030
1 Location
Caution
Tools
To avoid electrical shock and to prevent damage to the furnace, air conditioner,
and thermostat, disconnect the power supply before beginning work.
This can be done at the circuit breaker, or at the appliance.
3 Mount the 8030
C A U T I O N
Your thermostat is a precise instrument.
Please handle it with care.
Turn off electricity to the appliance before installing or
servicing thermostat or any part of the system. Do not
turn electricity back on until work is completed.
Do not short (jumper) across electric terminals at
control on furnace or air conditioner to test the system.
This will damage the thermostat and void your warranty.
All wiring must conform to local codes and ordinances.
This thermostat is designed for use with 24 volt AC and
millivolt systems. The thermostat should be limited to a
maximum of 1.0 amps; higher amperage may cause
damage to the thermostat.
On replacement installations, mount the new thermostat in place of the
old one if possible.
On new Installations, follow the guidelines listed below.
Locate the thermostat on an inside wall, about 5 ft. (1.5m) above the
floor, and in a room that is used often.
Do not install it where there are unusual heating conditions, such as: in
direct sunlight; near a lamp, radio, television, radiator register, or
fireplace; near hot water pipes in a wall; near a stove on the other side
of a wall.
Do not locate in unusual cooling conditions, such as: on a wall separating
an unheated room; or in a draft from a stairwell, door, or window.
Do not locate in a damp area.
This can lead to corrosion that will shorten thermostat life.
Do not locate where air circulation is poor, such as:
in a corner or an alcove; or behind an open door.
Do not install the unit until all construction work and painting has been
completed.
This thermostat does not require leveling.
You will need #1 Phillips screwdriver (small) and
Drill with 3/16-in. (4.8mm) bit for this installation.
Separate front from back of unit. Press up on the
catch on bottom of thermostat and swing the body
away from the base, lift up to remove the body
from the base. Hold the base against the wall, with
the wires coming through the opening below the
terminal block.
Position the base for best appearance. (If you chose to use the
optional wall plate, hold the wall plate against the wall, with the
wires coming through the opening. Then pull the wires through
the opening in the base unit. Position the base unit for best
appearance.)
Attach the base to the wall with the two screws provided.
If you are mounting the base to sheet rock or if you are
using the old mounting holes, use the
plastic anchors provided. Drill a 3/16-
in.(4.8mm) hole for the insert at each
screw location, then mount the base.
When you have finished making connections.
hook the top of the body onto the base, swing the
body down, and snap the body onto the base.
Note:
FOR ADVANCED USERS ONLY
FOR ADVANCED USERS ONLY
If you have an electric furnace system and the blower does
not operate after installation, remove the thermostat, turn it
over, and find the electric/gas heat selector jumper on the
back of the control unit. Switch the Gas/Elect. jumper to
Elect. to "Elect"(see Diag below).
1) The 8030 can run on batteries only. (2AA Alkaline) 24VAC and MV
The batteries will last well over 1 year. If the batteries are not replaced the
thermostat will stop working. Use the MV/C power jumper position.
2) The 8030 can run on the C wire if available. 24VAC ONLY
As shown in the wiring diagrams, The C wire is the other side of the 24VAC
heating transformer. If the C wire is used, the batteries are then for AC power
loss only and will last much longer. The thermostat will continue working if the
batteries die. Use the MV/C power jumper position.
5 Install Batteries
7 Power Options
6 Check Unit
6 Check Unit cont.
The 8030 requires batteries to
operate your furnace and retain its
programming in memory.
Switch MODE switch to OFF and
the FAN switch to AUTO.
Remove the unit from the wall turn it
over and install 2 AA alkaline batteries
according to the polarity noted in the
compartment.
Press the RESET button to clear
transient program memory. Initially, all
LCD segments will go off.
NOTE: Replace the batteries when this LOW battery indicator
appears on the display or once a year. When replacing
batteries, you have approximately one minute before your
custom program is lost.
Follow these procedures to verify you have correctly installed the unit.
To check HEAT mode:
Set the mode switch to HEAT. Set the fan switch AUTO.
Touch the main temperature display then
touch the TEMP UP arrow to raise the set
point to 90deg. Touch HOME. Allow the
system 5 min to respond.
Verify that heat is blowing from the system.
To check COOL mode:
Set the mode switch to COOL.
Touch the main temperature display then touch
the TEMP DOWN button to a temp 5 degrees
below the room temperature. Touch HOME.
Allow the system 5 min to respond. Verify that
cool air is blowing from the system.
To check Fan: (If you connected the G wire - fan relay)
Switch Mode to OFF during fan test.
Switch the FAN switch to the ON position. Verify air is blowing from vents.
After test, return to Fan switch to AUTO, and Mode to HEAT or COOL.
Good
5ft.
(1.5m)
Mode
Switch
Congratulations, you have successfully installed your unit.
Please proceed to the OPERATING Guide to initialize the new thermostat.
REMEMBER, Mode Switch must be in HEAT or COOL to operate the thermostat.
PG
1
PG
2
PG
3
PG
4
PG
7
PG
8
PG
9
PG
10
Terminal
Block
Wall Plate
GAS ELECT
FURN
MV/C
Gas/
Electric
jumper
Circuit
Board
Power Mode
jumper
Rear View of control unit
Install guide 8030
RESET
MENU
PROGRAM
RESET
MENU
PROGRAM
LOWBATT
AA
AA
GAS
MV/C
FURN
ELECT
RESET
MENU
PROGRAM
RESET
MENU
PROGRAM
Fan
Switch
MENU
button
PROGRAM
button
2 Remove old unit
Switch electricity to the furnace and air conditioner OFF;
then proceed with the following steps.
Remove cover from old thermostat. Most are snap-on types and simply pull
off. Some have locking screws on the side or front. These must be
loosened. Note the letters printed near the terminals.
Attach labels (enclosed) to each wire for identification.
Label the wires one at a time. You must have all the wires labeled before
you proceed. With all wires labeled, remove them from the
old unit.
Make sure the wires do not fall back inside the
wall. Wind them around a pencil to keep them from
falling.
Remove the old thermostat from the wall.
Fill wall opening with non-combustible insulation to
prevent drafts.
B
G
W
Caution
Read instructions carefully before removing any wiring from existing
thermostat. Wires must be labeled before they are removed. THERE IS NO
STANDARD COLOR CODE. When removing wires from their terminals,
ignore the color of the wires since these may not follow the standard.
Customer Support: 888-515-2585 or Visit our website www.ritetemp.biz
3) The 8030 can run on 24VAC series power. 24VAC ONLY
Power for the thermostat is borrowed from the furnace relay. Therefore this options ONLY
works with 24VAC systems, and with a heat relay current of between .2 and .6 amps. Do not
use the FURN mode unless this current can be verified by a heating contractor. The batteries
are then for AC power loss only and will last much longer. The thermostat will continue working
if the batteries die. Use the
FURN power jumper position.
To locate the Power Mode
Jumpers. Remove the control unit
from the wall mount, turn it over,
and locate the jumper. It is set at
the factory on MV/C. Change it
from MV/C to FURN to use series
power.
NOTE: This option works with
24VAC, .2 to .6 amp. systems only.
Verify
operation. If it doesn't work
go back to options 1 or 2.
PG
5
PG
6
PG
16
4 Before you Connect Wires
Caution
D o n o t a l l o w w i r e s t o t o u c h e a c h o t h e r o r p a r t s o n
t h e r m o s t a t . W i r e s m u s t b e r o u t e d t h r o u g h t h e h o l e i n t h e
b a c k p l a t e , b e l o w t h e t e r m i n a l b l o c k , o r t h e y w i l l h i t p a r t s
o n t h e c o v e r.
Please follow these guidelines for safe and secure wire connections.
Determine which step-by-step wiring diagram you should use. Make sure your
wires are labeled. This may require you to find the 'other end' connection for
each wire on your heating or air conditioning equipment and read the label
there.
If you have a wire make "C" its connection is optional. If you do connect it,
the thermostat will draw power from the C wire and this will extend battery life.
Optional Wire Connections
5 What Wires Do You Have?
Strip insulation 3/8 in. (9.5mm) from wire ends.
Take care not to damage the labels for each wire in handling.
Connect labeled wires only to a terminal with corresponding
letter.
Bend the wire slightly, insert the wire under the contact plate
and tighten the screw down onto the wire.
PG
14
PG
15
PG
13
RH
G
Y
W
C
From Furnace
And AC unit
R
or
B
G
Y
R
C
From single stage
heat pump
O
or
RC
G
Y
W
C
From Furnace
And AC unit
RH
Go To Page 13
Go To Page 14
Go To Page 12
R
or
RH
W
C
From Furnace
G
From Furnace
and AC unit
G
W
Y
RH
RC
C
R
G
Y
W
C
RH
or
From Furnace
and AC unit
PG
11
PG
12
STEP 1 - Connect the R (or RH)
wire to the RH terminal on the
thermostat.
This connects the Heater Power to
the thermostat.
STEP 2 - Connect the W wire to the
W terminal on the thermostat.
This connects the heater control line
to the thermostat.
Your Heater is now connected to the
thermostat.
STEP 1 - Connect the R (or RH)
wire to the RH terminal on the
thermostat. This connects to the
Heater Power .
STEP 2 - Connect the W wire to the W
terminal on the thermostat.
This connects the heater control line to
the thermostat.
STEP 3 - Connect the G wire to the G
terminal on the thermostat.
This connects the Fan to the thermostat.
Your system is now connected to the thermostat.
Return To Page 7
Return To Page 7
STEP 1 - Connect the Y wire to the
Y terminal on the thermostat. This
connects to the Cooler compressor.
STEP 2 - Connect the RH or R wire to
the RH terminal on the thermostat.
This connects the Heater/Cooler Power.
STEP 3 - Connect the W wire to the W terminal on the
thermostat. This connects to the heater control line.
STEP 4 - Connect the G wire to the G terminal on the Thermostat. This
connects to the Fan.
Your HVAC system is now connected to the thermostat.
STEP 1 - Remove the orange
Jumper wire.
STEP 2 - Connect the Y wire to
the Y terminal on the thermostat.
This connects to the Cooler
compressor.
STEP 3 - Connect the RH wire to the RH
terminal on the thermostat. This connects to the
Heater Power .
STEP 4 - Connect the RC wire to the RC terminal on
the thermostat. This connects to the Cooling Power .
STEP 5 - Connect the W wire to the W terminal on the thermostat.
This connects to the heater control line.
STEP 6 - Connect the G wire to the G terminal on the Thermostat.
This connects to the Fan.
Your HVAC system is now connected to the thermostat.
Return To Page 7
STEP 1 - Connect the G wire to the G
terminal on the thermostat.
This connects the Fan.
STEP 2 - Add a jumper wire between
W and Y.
STEP 3 - Connect the Y wire to the Y
terminal on the thermostat.
This connects the Compressor.
STEP 4 - Connect the O or B wire to the O or B terminal
on the thermostat. (If you have both O and B contact
Ritetemp or your local HVAC contractor for further help)
This connects the change over valve.
STEP 5 - Connect the R wire to the RC terminal on the Thermostat.
This connects to the 24vac power.
Your HVAC system is now connected to the thermostat.
Return To Page 7
Return To Page 7
SINGLE STAGE
HEAT PUMP
5 WIRE
4 WIRE
2 WIRE Heating
(GAS MILLIVOLT or 24vac
NOTE: Wires marked with the dotted line are optional.
NOTE: Wires marked with the dotted line are optional.
NOTE: Wires marked with the dotted line are optional.
NOTE: Wires marked with the dotted line are optional.
NOTE: Wires marked with the dotted line are optional.
3 WIRE
From Furnace
and AC unit
R
G
Y
C
O
or
B
Go To Page 15
R - Single source power for heat/cool
Note: R connects to both RC and RH using the Orange
jumper
RH or 4 - HEATING POWER
RC - COOLING POWER
W - HEATING CONTROL
G - FAN RELAY
C - Common side of Heating Power
Y - COMPRESSOR
O - DAMPER OR CHANGEOVER VALVE
(POWERED IN COOL)
B - DAMPER OR CHANGEOVER VALVE
(POWERED IN HEAT)
W
RH
R
or
From Furnace
Go To Page 11
C
FURNACE
jumper
wire
Heat
Power
Heat
W
G
RH
C
FAN
Thermostat
HVAC SYSTEM
jumper
wire
Heat
Power
Heat
W
G
RH
C
FAN
Y
Cool
Comp
Thermostat
HVAC SYSTEM
Remove
jumper
wire
HEAT
Power
Heat
W
G
RH
RC
C
FAN
Y
Cool
Comp
COOL
Power
Thermostat
O or B
Single Stage HEAT PUMP
Change
Over
G
O or B
R
C
FAN
Y
Comp
24VAC
Power
jumper
wire
jumper
wire
Thermostat
jumper
wire
FURNACE
HEAT
Thermostat
R
W
C
HEAT
Power
W
RH
R
or
From Furnace
C
RH
W
C
From Furnace
G
or R
The 8030 can be used with most 24 volt gas, oil or electric heating and air conditioning systems,
single-stage heat pumps or gas millivolt heating systems. It cannot be used with 120 volt heating
systems or multistage heat pumps. Ask The Home Depot for other thermostats to control those
systems.
The 8030 is programmable. There are four programming
periods per day. Each period can be programmed separately.
You can use the built-in time/temperature programs, or alter
them to suit your schedule.
The 8030 separately programs each weekday, Saturday, and
Sunday - for both heating and cooling.
You can easily override the programmed temperatures for as
little as one programming period or for an entire vacation.
The large liquid crystal touch screen display shows time, day
of the week, room and set temperatures. It will also remind
you when the filter should be changed in your blower.
Temperature swing adjustment lets you fine-tune your system for maximum comfort and
energy efficiency.
A 4-minute minimum off time in COOL protects your air conditioning system from being
damaged.
Two "AA" batteries (included) are used to retain your time and temperature programs, and to
8030 Features
RESET
MENU
PROGRAM