1. DL manuals
  2. RLE Technologies
  3. Switch
  4. F1000
  5. User Manual

RLE Technologies F1000 User Manual

Manual is about: F-Series

Summary of F1000

  • Page 1

    Monitoring & notification f3400/f1000 (f-series) user guide.

  • Page 2

    Rletech.Com 2 970.484.6510 copyright notice ©2010 rle technologies. All rights reserved. No part of this publication may be reproduced or distributed in any form or by any means, or stored in a database or retrieval system, without the prior written permission of rle technologies. Trademark notices ...

  • Page 3

    970.484.6510 3 rletech.Com product registration product registration helps rle technologies inform owners of: • product upgrades • firmware enhancements • new products and technologies • special offers available only to registered users access and submit product registration information from the f10...

  • Page 4

    Rletech.Com 4 970.484.6510 notes:.

  • Page 5

    Contents rletech.Com 5 970.484.6510 1 system overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 product description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 fro...

  • Page 6

    970.484.6510 6 rletech.Com 4 configuration menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 relay...

  • Page 7

    970.484.6510 7 rletech.Com a analog input 4-20ma reference chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 b f3400/f1000 accessories wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 configuring the seahawk ld5100 as an analog input . . . . . . ....

  • Page 8

    970.484.6510 8 rletech.Com notes:.

  • Page 9

    Figures rletech.Com 9 970.484.6510 1 system overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 figure 1.1 front panel indicators and controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 figure 1.2 terminal block designations ....

  • Page 10

    Rletech.Com 10 970.484.6510 figure 4.13 modbus interface configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 figure 4.14 ld unit modbus slave configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 figure 4.15 modbus register data log page . . . ...

  • Page 11

    Tables rletech.Com 11 970.484.6510 1 system overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 table 1.1 terminal block designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 table 1.2 rear panel status indicat...

  • Page 12

    970.484.6510 12 rletech.Com notes:.

  • Page 13: Ystem

    Www.Rletech.Com 13 970.484.6510 c h a p t e r c hapter 0 s ystem o verview 1.1. Product description the f3400/f1000 monitoring system is a comprehensive system which provides additional equipment protection by monitoring critical operating parameters in enterprises, remote network facilities, commun...

  • Page 14: 1.2.

    Www.Rletech.Com 14 970.484.6510 1 system overview 1.2. Front panel indicators and controls figure 1.1 front panel indicators and controls communications leds – four modem status leds tx – green (on) if information is being transmitted. Rx – green (on) if information is being received. Oh – green (on...

  • Page 15: 1.3.

    Www.Rletech.Com 15 970.484.6510 1 system overview 1.3. Terminal block designations table 1.1 terminal block designations tb1-1 (+) input for 24vdc power tb1-2 (-) input for 24vdc power p1 24vdc wall adapter input (center +) tb2-1 channel 1 positive (+) tb2-2 channel 1 negative (-) tb2-3 channel 1 gr...

  • Page 16

    Www.Rletech.Com 16 970.484.6510 1 system overview tb4-1 com1 eia 485 positive (+) (configurable) tb4-2 com1 eia 485 negative (-) (configurable) tb4-3 eia 485 ground tb4-4 com1 eia485 positive (+) (configurable) tb4-5 com1 eia485 negative (-) (configurable tb4-6 eia485 ground sw1-1 unit eia485 termin...

  • Page 17

    Www.Rletech.Com 17 970.484.6510 1 system overview figure 1.2 terminal block designations tb5-24 channel 20 negative (-) tb5-25 channel 21 positive (+) tb5-26 channel 21 negative (-) tb5-27 channel 22 positive (+) tb5-28 channel 22 negative (-) tb5-29 channel 23 positive (+) tb5-30 channel 23 negativ...

  • Page 18: 1.4. Rear

    Www.Rletech.Com 18 970.484.6510 1 system overview 1.4. Rear panel indicators the rear panel of the f3400/f1000 houses a pair of green leds. The chart below tracks indicator status when the corresponding green led is illuminated: figure 1.3 rear led indicator and status 1.5. Sw1 switch settings sw1-1...

  • Page 19: Etting

    Www.Rletech.Com 19 970.484.6510 c h a p t e r c hapter 0 g etting s tarted 2.1. Installation the f3400/f1000 comes in a 19 inch (.48m) rack mount enclosure. Install the f3400/f1000 in the rack. Use the proper anchoring method to mount the unit securely. Supply the 24vdc to the unit. 2.2. Communicati...

  • Page 20: Ping Commands

    Www.Rletech.Com 20 970.484.6510 2 getting started 2.3.1 set the f3400/f1000's ip address using the arp and ping commands to set the ip address of a manufacturer programmed f3400/f1000, you can use the arp (address resolution protocol) command together with the ping (icmp echo request) command. Howev...

  • Page 21: Browser

    Www.Rletech.Com 21 970.484.6510 2 getting started 2.3.1.4 troubleshooting the arp/ping commands if problems are encountered, it may be for one of the following reasons: the f3400/f1000 already has a non-default tcp/ip address. Once the ip address of the f3400/f1000 has been changed from the default ...

  • Page 22: Connection

    Www.Rletech.Com 22 970.484.6510 2 getting started 2.3.3 set the f3400/f1000’s ip address using an eia232 connection to use the eia232 interface: 1 connect the eia232 port (p2 eia232 - com1) on the f3400/f1000 to a terminal or pc running terminal emulation software (hyperterminal) with a 9-pin male-f...

  • Page 23: 2.4. F3400/f1000

    Www.Rletech.Com 23 970.484.6510 2 getting started 2.4. F3400/f1000 wiring rle technologies recommends an 18awg stranded copper wire for connection from each monitored point to a terminal block (tb) connection on the f3400/f1000. Rle recommends no more than 500 feet (152.4m) of wire at this specifica...

  • Page 24

    Www.Rletech.Com 24 970.484.6510 2 getting started 2.4.2 eia232 com1 connection the eia232 port can be connected to a pc for local configuration, firmware downloads, and troubleshooting. It is typically a temporary connection. Connect the straight through, 9-pin, cable as shown in figure 2.2. Figure ...

  • Page 25

    Www.Rletech.Com 25 970.484.6510 2 getting started 2.4.4 rj45 ethernet connection the f3400/f1000 has an internal 10base-t ethernet port used to configure and monitor the f3400/f1000. The ethernet port supports web browser access, email (smtp), bacnet, and snmp. The following figures show the physica...

  • Page 26

    Www.Rletech.Com 26 970.484.6510 2 getting started 2.4.5 relay k1 and k2 connection relay outputs may be used to unlatch doors, signal annunciators, signal ip cameras, and to turn on auxiliary equipment such as exhaust fans. Relay outputs are form c (spst). Refer to appendix d, “technical specificati...

  • Page 27: F3400/f1000 W

    Www.Rletech.Com 27 970.484.6510 c h a p t e r c hapter 0 f3400/f1000 w eb i nterface 3.1. F3400/f1000 web interface overview the f3400/f1000's web interface provides a convenient way to check the f3400/f1000’s status and reconfigure basic settings from any internet enabled computer. The f3400/f1000 ...

  • Page 28: 3.2.1 Historical Data

    Www.Rletech.Com 28 970.484.6510 3 f3400/f1000 web interface the top of the page provides links to other pages for additional monitoring, control and configuration. The falcon logo (default), ip camera image or company logo can be displayed on the main menu. The bottom of the f3400/f1000 main menu fe...

  • Page 29

    Www.Rletech.Com 29 970.484.6510 3 f3400/f1000 web interface the following format is used to record each alarm entry: ah###-id-condition-date time (value uom) label ah### is the alarm entry index. Id is the alarm identifier number; refer to appendix c, “alarm id reference tables” on page 87. Conditio...

  • Page 30

    Www.Rletech.Com 30 970.484.6510 3 f3400/f1000 web interface 3.2.1.3 digital status history figure 3.4 example of the digital status history page digital status history displays a history of the state of digital points configured as “status” points. A digital input can be configured as no (normally o...

  • Page 31

    Www.Rletech.Com 31 970.484.6510 3 f3400/f1000 web interface 3.2.1.5 data history figure 3.6 example of the data history page data history provides an intermediate page to assist in navigating to the desired data. Only points configured as analog 4-20ma and thermistor are shown. The data history text...

  • Page 32

    Www.Rletech.Com 32 970.484.6510 3 f3400/f1000 web interface 3.2.1.7 data history text downloads this link helps navigate to the desired data. Figure 3.8 example of the data history text download page 3.2.1.8 server history figure 3.9 example of the server history page server history displays the pas...

  • Page 33: 3.3. Identity

    Www.Rletech.Com 33 970.484.6510 3 f3400/f1000 web interface 3.2.1.9 server status figure 3.10 example of the server status page server status displays the current status of each server selected to be monitored. The status field is color coded. White indicates the relay output is de-energized; red in...

  • Page 34: 3.4. Web

    Www.Rletech.Com 34 970.484.6510 3 f3400/f1000 web interface 3.4. Web links figure 3.12 example of the web links display page web links displays still images (.Jpg) from all ip cameras and other urls linked to the f3400/ f1000. 3.5. Configuration figure 3.13 configuration menu the configuration link ...

  • Page 35: Onfiguration

    Www.Rletech.Com 35 970.484.6510 c h a p t e r c hapter 0 c onfiguration m enu the configuration page allows users with administrator or read-write privileges to adjust the f3400/f1000’s settings. Each link on the configuration page displays more information about specific configuration settings. Fig...

  • Page 36: 4.1. Inputs

    Www.Rletech.Com 36 970.484.6510 4 configuration menu 4.1. Inputs figure 4.2 inputs configuration page inputs allow users to program specific parameters for each f3400/f1000 input. This model allows different numbers of inputs. Only installed inputs are displayed. Inputs are identified by their name ...

  • Page 37

    Www.Rletech.Com 37 970.484.6510 4 configuration menu select input type: select based on the type of device connected to the input channel. Options include: not configured – select when there is nothing connected to the input. Analog 4-20ma – select when the device connected to the input provides a 4...

  • Page 38

    Www.Rletech.Com 38 970.484.6510 4 configuration menu example: temperature sensor with a sensing range of 50-95°f - displayed in fahrenheit gain = (95-50) / 4 = 11 (round to the nearest integer) offset = 50 - 11 = 39 example: temperature sensor with a sensing range of 50-95°f - displayed in celsius c...

  • Page 39

    Www.Rletech.Com 39 970.484.6510 4 configuration menu alarm delay: the amount of time the f3400/f1000 waits to send an alert after an alarm condition is detected. The f3400/f1000 uses this same time delay to report a return to normal after the alarm condition clears. The alarm delay is active for all...

  • Page 40: 4.2. Relays

    Www.Rletech.Com 40 970.484.6510 4 configuration menu email recipient notification: allows up to four email addresses to be designated for notification if the input goes into alarm. Email addresses will be displayed once they are entered on the email configuration page. Email notification will be sen...

  • Page 41: 4.3. Schedules

    Www.Rletech.Com 41 970.484.6510 4 configuration menu 4.3. Schedules figure 4.5 schedules configuration menu the schedules page allows users to schedule the activation and deactivation of relay outputs. This is useful for cycling redundant equipment such as chillers, generators, etc. Relays are assig...

  • Page 42: 4.4. Alarm

    Www.Rletech.Com 42 970.484.6510 4 configuration menu 4.4. Alarm management figure 4.6 alarm management the alarm management link allows users to acknowledge current f3400/f1000 alarms and clear the f3400/f1000's alarm history logs. Click the button and enter the appropriate code or user's initials t...

  • Page 43: 4.5. Modem

    Www.Rletech.Com 43 970.484.6510 4 configuration menu 4.5. Modem the modem link allows users to configure the f3400-m/f1000’s internal modem (if the option is available). This instructs the f3400-m/f1000-m when, how, and whom to call when an alarm occurs. See definitions below for more information. F...

  • Page 44

    Www.Rletech.Com 44 970.484.6510 4 configuration menu redial interval: establishes the number of minutes (1-255) to wait between redials. Enter 0 to disable this function. Dial back on returns: determines whether to call the number again once the alarm condition returns to normal. Force alarm acknowl...

  • Page 45

    Www.Rletech.Com 45 970.484.6510 4 configuration menu pager id: mandatory for numeric and alphanumeric pagers. Alphanumeric pager – the id entered is sent to the paging service along with all queued alarm messages. The id is the unique pin for a specific pager. The id may be a maximum of 16 character...

  • Page 46: 4.6. Web

    Www.Rletech.Com 46 970.484.6510 4 configuration menu 4.6. Web links figure 4.9 configuring web links the main menu of the f3400/f1000's web interface displays a large image and links to other images. These images can be graphics, logos or images from an ip camera. The web link page allows users to s...

  • Page 47: 4.7. Egg/nest

    Www.Rletech.Com 47 970.484.6510 4 configuration menu 4.7. Egg/nest figure 4.10 egg/nest configuration page setting the egg login as referred – nologin allows the f3400/f1000 nest unit to access the f3400/f1000 egg without a password. If password protection is desired, select always login. The egg al...

  • Page 48: 4.9. Snmp/syslog

    Www.Rletech.Com 48 970.484.6510 4 configuration menu 4.9. Snmp/syslog figure 4.12 snmp/syslog configuration page persistent v1,v2c-traps: enables the f3400/f1000 to issue continuous snmp traps until an alarm acknowledgement is received by the f3400/f1000 or until the alarming point returns to normal...

  • Page 49: 4.10. Modbus

    Www.Rletech.Com 49 970.484.6510 4 configuration menu 4.10. Modbus interface figure 4.13 modbus interface configuration the modbus interface page allows users to configure modbus features for rle products and enable modbus slave capabilities for the unit. Modbus/tcp slave unit identifier: enables and...

  • Page 50

    Www.Rletech.Com 50 970.484.6510 4 configuration menu modbus master poll timeout: sets the amount of time the f3400/f1000 waits for a response from the slave device before moving on to read the next register. It is normally set to the default of 1. It is adjustable from 1 to 10 seconds. Modbus master...

  • Page 51: 4.10.3 Modbus Packet Log

    Www.Rletech.Com 51 970.484.6510 4 configuration menu email recipient notification: select the recipient email addresses that require notification when any alarm occurs on this slave. The email addresses correspond to the email addresses configured from the email configuration page. 4.10.2 modbus reg...

  • Page 52: 4.10.4 Reset Modbus Port

    Www.Rletech.Com 52 970.484.6510 4 configuration menu column 1 = system up time. Column 2 = modbus master register number. Column 3 = direction of packet: out = packet sent from the f3400/f1000 (master request). Column 4 = modbus packet. 4.10.4 reset modbus port this link allows users to reset the mo...

  • Page 53: 4.11. Bacnet

    Www.Rletech.Com 53 970.484.6510 4 configuration menu 4.11. Bacnet figure 4.17 bacnet configuration bacnet device name, bacnet device id and bacnet description, bacnet udp port: required for the f3400/f1000 to allow a building management system (bms) to poll the f3400/f1000’s inputs using the bacnet ...

  • Page 54: 4.12. Server

    Www.Rletech.Com 54 970.484.6510 4 configuration menu 4.12. Server ping figure 4.18 server ping configuration the server ping page allows a user to monitor up to 16 devices by pinging at set intervals. Ping interval (minutes): the time in minutes the f3400/f1000 will take to request time updates from...

  • Page 55: 4.13. System

    Www.Rletech.Com 55 970.484.6510 4 configuration menu 4.13. System figure 4.19 system configuration the system link allows users to configure basic f3400/f1000 information. The f3400/f1000's ip address and point-to-point protocol may also be configured through this menu, via the ip configuration menu...

  • Page 56: 4.14. Clock

    Www.Rletech.Com 56 970.484.6510 4 configuration menu 4.14. Clock figure 4.20 clock configuration the clock page allows users to set the date and time on the f3400/f1000's internal clock. Enter the date using a mm/dd/yy format, where mm is a two digit month, dd is a two digit day, and yy is a two dig...

  • Page 57: 4.16.

    Www.Rletech.Com 57 970.484.6510 4 configuration menu f3400/f1000’s webpages over a dial-up connection. The remote pc’s dial-up settings should be set to “obtain an ip address automatically”. Note changes will not go into effect until the submit changes button is clicked. 4.16. User administration (w...

  • Page 58: 4.17. Email

    Www.Rletech.Com 58 970.484.6510 4 configuration menu 4.17. Email figure 4.23 email configuration the email page allows users to configure the f3400/f1000 to send notification via email when inputs are in an alarm state. The f3400/f1000 will send one email message per alarm instance to a maximum of f...

  • Page 59: 4.18.

    Www.Rletech.Com 59 970.484.6510 4 configuration menu smtp password: used for esmtp; use the recommended default setting unless instructed differently by your it department. Dun user name and password: only used if ppp is selected. The dun username and password specifies the dial-up network user name...

  • Page 60: 4.19. Network

    Www.Rletech.Com 60 970.484.6510 4 configuration menu dst begin date: enter the date daylight savings time will begin. Dst end date: enter the date daylight savings time will end. 4.19. Network statistics figure 4.25 setting the network statistics the network statistics page displays network and eia4...

  • Page 61: 4.21. Product

    Www.Rletech.Com 61 970.484.6510 4 configuration menu f1000 will automatically reboot. See chapter 8, “upgrading firmware and managing configuration data” on page 73, for more detailed instructions. 4.21. Product registration figure 4.27 product registration located at www.Rletech.Com the product reg...

  • Page 62

    Www.Rletech.Com 62 970.484.6510 4 configuration menu notes:.

  • Page 63: Eia-232 I

    Www.Rletech.Com 63 970.484.6510 c h a p t e r c hapter 0 eia-232 i nterface the f3400/f1000’s eia-232 interface provides a more detailed and intricate view of the f3400/f1000. It also allows a user to access more elaborate configuration options. In order to proceed through this chapter, the f3400/f1...

  • Page 64: 5.1.

    Www.Rletech.Com 64 970.484.6510 5 eia-232 interface 2 set the appropriate com port to 9600 baud, no parity, 8 data bits, 1 stop bit, (9600/n/8/ 1), and no software or hardware flow control. Figure 5.2 com1 properties screen 3 once the terminal emulation software starts, press enter on the keyboard a...

  • Page 65: 5.3. Main

    Www.Rletech.Com 65 970.484.6510 5 eia-232 interface 5.3. Main menu all system functions begin in the main menu. Two letter commands display information, execute commands and display submenus for additional inquiry and system configuration functions. The bootloader section is designed for experienced...

  • Page 66

    Www.Rletech.Com 66 970.484.6510 5 eia-232 interface 5.3.1 main configuration menu – sc typing sc at the command prompt on the main menu displays the main configuration menu that lists all items for system setup and configuration. This menu may be password protected. If it is, the password must be en...

  • Page 67

    Www.Rletech.Com 67 970.484.6510 5 eia-232 interface 5.3.2 ip configuration menu the ip configuration menu is accessed by typing a 1at the command prompt in the main configuration menu. This menu is used to establish ip/tcp and ppp interaction with the network. The f3400/f1000 must be set up with an ...

  • Page 68

    Www.Rletech.Com 68 970.484.6510 5 eia-232 interface q quit does not save changes and returns user to the main menu. X exit & save saves changes and returns user to the main menu. Table 5.3 ip configuration menu commands (continued) command description function.

  • Page 69: Emote

    Www.Rletech.Com 69 970.484.6510 c h a p t e r c hapter 0 r emote a ccess 6.1. Remote access configuration (modem option) the f3400/f1000 can be remotely accessed with any terminal emulation software package. To establish a proper dial-out session, set the appropriate modem port as follows: 33.6k bau...

  • Page 70

    Www.Rletech.Com 70 970.484.6510 6 remote access type a question mark (?) to view the system menu. To terminate the session, execute the command in the software package that disconnects the modem. The commands for accessing the system remotely are identical to the ones described earlier in this user ...

  • Page 71: Oint

    Www.Rletech.Com 71 970.484.6510 c h a p t e r c hapter 0 p oint - to -p oint p rotocol point-to-point protocol (ppp) is an alternate method that may be used to communicate with the f3400/f1000. Ppp can only be used through a modem, over a phone line. The f3400/f1000 and the user’s computer must both...

  • Page 72: 7.2.

    Www.Rletech.Com 72 970.484.6510 7 point-to-point protocol 7.2. Configuring the pc now the user is ready to configure the pc they will be dialing in from. These directions were written from a windows xp machine. To configure the pc: 1 click on start, control panel, then network and internet connectio...

  • Page 73: Pgrading

    Www.Rletech.Com 73 970.484.6510 c h a p t e r c hapter 0 u pgrading f irmware and m anaging c onfiguration d ata 8.1. Upgrading f3400/f1000 firmware you can upgrade f3400/f1000 firmware using either the: tftp client eia-232 interface follow the instructions for the method you want to use..

  • Page 74

    Www.Rletech.Com 74 970.484.6510 8 upgrading firmware and managing configuration data 8.1.1 upgrading f3400/f1000 firmware via tftp client this is the preferred method. However, it does not work with a ppp connection. 1 download the most recent version of firmware appropriate for your f3400/f1000 fro...

  • Page 75: Com1 Port (X-Modem)

    Www.Rletech.Com 75 970.484.6510 8 upgrading firmware and managing configuration data 8.1.2 updating f3400/f1000 firmware via the eia232 com1 port (x-modem) 1 connect to the f3400/f1000 using hyperterminal. For instruction on how to do so, see our support document “connect hyperterminal” available on...

  • Page 76: 8.2.

    Www.Rletech.Com 76 970.484.6510 8 upgrading firmware and managing configuration data 8.2. Loading/saving f3400/f1000 configuration data this menu allows user configurations to be saved and reloaded onto other f3400/f1000, or in the unlikely event the f3400/f1000 fails, a replacement f3400/f1000 can ...

  • Page 77: (X-Modem)

    Www.Rletech.Com 77 970.484.6510 8 upgrading firmware and managing configuration data 8.2.3 loading configuration data via tftp client before the configuration can be loaded onto other f3400/f1000s, it must be checked for accuracy. Blank spaces or unwanted characters, such as the “press to download t...

  • Page 78

    Www.Rletech.Com 78 970.484.6510 8 upgrading firmware and managing configuration data notes:.

  • Page 79: Nalog

    Www.Rletech.Com 79 970.484.6510 a p p e n d i x c hapter 0 a nalog i nput 4-20 m a r eference c hart analog 4-20ma gain/offset conversion formula: gain = sensor range (high value - low value) / 4 offset = sensor low value - gain example: th140 humidity gain = (high value (100) -low value (0)) / 4 = ...

  • Page 80

    Www.Rletech.Com 80 970.484.6510 a analog input 4-20ma reference chart ct20 current 0 - 30 amps 0 - 60 amps 0 - 120 amps 7 15 30 -7 -15 -30 ct200 current 0 - 20 amps 0 - 200 amps 5 50 -5 -50 ct300 current 0 - 100 amps 0 - 300 amps 25 75 -25 -75 voltage pt300 voltage - single phase 0 - 300 vac 75 -75 ...

  • Page 81: F3400/f1000 A

    Www.Rletech.Com 81 970.484.6510 a p p e n d i x c hapter 0 f3400/f1000 a ccessories w iring the following figures show the typical wiring between the f3400/f1000 monitoring system and other products offered by rle technologies. Figure b.1 t120d temperature sensors figure b.2 th140 & th140d temperatu...

  • Page 82

    Www.Rletech.Com 82 970.484.6510 b f3400/f1000 accessories wiring figure b.3 dwyer temperature/humidity sensors figure b.4 bapi temperature/humidity sensor figure b.5 smk smoke detector, photoelectric.

  • Page 83

    Www.Rletech.Com 83 970.484.6510 b f3400/f1000 accessories wiring figure b.6 hd150 & hd150-2 gas sensors figure b.7 sd spot detectors figure b.8 pfm power fail monitor.

  • Page 84: B.1.

    Www.Rletech.Com 84 970.484.6510 b f3400/f1000 accessories wiring figure b.9 seahawk ld5100/ld2000 distance read leak detection (dry contact) b.1. Configuring the seahawk ld5100 as an analog input the f3400/f1000 averages/filters the analog inputs. The ld5100 will output approx. 3.95ma when there is ...

  • Page 85

    Www.Rletech.Com 85 970.484.6510 b f3400/f1000 accessories wiring for assistance wiring the following f3400/f1000 accessories also offered by rle, please contact our technical support department at (970) 484-6510: ct55 and ct200 single phase current sensor ct300 and ct800 single phase current sensor ...

  • Page 86

    Www.Rletech.Com 86 970.484.6510 b f3400/f1000 accessories wiring notes:.

  • Page 87: Larm

    Www.Rletech.Com 87 970.484.6510 a p p e n d i x c hapter 0 a larm id r eference t ables c.1. Analog tables table c.1 analog alarm id reference tables, inputs 1-4 channel condition id 1 high limit 1 001 1 low limit 1 002 1 high limit 2 003 1 low limit 2 004 2 high limit 1 005 2 low limit 1 006 2 high...

  • Page 88: C.2. Thermistor

    Www.Rletech.Com 88 970.484.6510 c alarm id reference tables c.2. Thermistor tables table c.2 thermistor alarm id reference tables, inputs 5-8 channel condition id 5 high limit 1 017 5 low limit 1 018 5 high limit 2 019 5 low limit 2 020 6 high limit 1 021 6 low limit 1 022 6 high limit 2 023 6 low l...

  • Page 89: C.3. Digital

    Www.Rletech.Com 89 970.484.6510 c alarm id reference tables c.3. Digital tables table c.3 digital alarm id reference tables, digital inputs 5 through 32 channel condition id 5 on/off 085 6 on/off 086 7 on/off 087 8 on/off 088 9 on/off 089 10 on/off 090 11 on/off 091 12 on/off 092 13 on/off 093 14 on...

  • Page 90

    Www.Rletech.Com 90 970.484.6510 c alarm id reference tables notes:.

  • Page 91: Echnical

    Www.Rletech.Com 91 970.484.6510 a p p e n d i x c hapter 0 t echnical s pecifications table d.1 technical specifications power 24vdc model: 24vdc (±10%), 600ma max., wall adaptor included inputs analog/digital f1000 4 configurable as 4-20ma (12-bit a/d conversion), 4 as digital input or thermistor f...

  • Page 92

    Www.Rletech.Com 92 970.484.6510 d technical specifications protocols tcp/ip; udp/ip; icmp/ip; ftp; ntp; telnet ipv4.0; up to 5 url links to other ip addressable cameras/ devices; webpages comply with rehabilitation act of 1973, sections 504 and 508, us dept of education (website accessibility for co...

  • Page 93

    Www.Rletech.Com 93 970.484.6510 d technical specifications login security web browser access (ethernet, modem ppp) 1 administrator plus 7 users individually selectable for read only, read/write or administrator terminal emulation access (modem, eia232) 1 administrator (password for both modem and ei...

  • Page 94

    Www.Rletech.Com 94 970.484.6510 d technical specifications notes:.