1. DL manuals
  2. S&C
  3. Radio
  4. SpeedNet
  5. Installation Instructions Manual

S&C SpeedNet Installation Instructions Manual

Summary of SpeedNet

  • Page 1

    S&c speednet ® radio installation instructions table of contents section page introduction qualified persons............................................................. .2 read this instruction sheet. ............................................. .2 retain this instruction sheet. .....................

  • Page 2: Introduction

    Introduction qualified persons read this instruction sheet retain this instruction sheet latest document release warranty w arning the equipment covered by this publication must be installed, operated, and maintained by qualified persons who are knowledgeable in the installation, operation, and main...

  • Page 3: Safety Information

    Safety information warranty of the speednet radio is contingent upon the installation, configuration, and use of the speednet radio and software in accordance with s&c's applicable instruction sheets. This warranty does not apply to major components not of s&c manufacture, such as batteries, and oth...

  • Page 4: Installation

    Installation overview these instructions describe steps you should complete in the shop prior to field installation, and field installation steps that are specific to the speednet radio. Pre-installation checklist before you install the speednet radio, carry out the following steps. This is best don...

  • Page 5: Installation

    Installation the aodv protocol generates fewer transmissions, and conserves network capacity. Each route request has a sequence number tracked by the nodes, so that they will not repeat a previous route request. Route requests also have a time-to-live indicator, that restricts the number of times th...

  • Page 6: Installation

    Installation private subnets there are three ip network addresses reserved for private networks. The addresses are 10.0.0.0, subnet mask 255.0.0.0, 172.16.0.0, subnet mask 255.240.0.0, and 192.168.0.0, subnet mask 255.255.0.0. These addresses are also notated 10.0.0.0/8, 172.16.0.0/12, and 192.168.0...

  • Page 7: Installation

    Installation on broadcast networks, such as ethernet, the mac address allows each node to be uniquely identified and allows frames to be marked for specific nodes. It thus forms the basis of most of the layer 2 networking upon which higher osi layer protocols are built, to produce complex functionin...

  • Page 8: Installation

    Installation network example use of private ip addresses is strongly recommended when configuring a speednet radio network. The following example of a speednet radio network uses several private ip subnets from the 192.168.0.0 block of private addresses. The speednet radio network, depicted in figur...

  • Page 9: Installation

    Installation 9 1072-510 1072-510 figure 2. Example of a network using speednet aodv..

  • Page 10: Installation

    Routing options as a router, speednet radios provide a wireless connection between two or more separate ethernet subnets. Data is then routed between the ethernet subnets. Route information can be entered manually, or can be processed automatically by aodv, the speednet radio algorithm. The type of ...

  • Page 11: Installation

    Installation it is recommended that all hosts from subnet 2 use 192.168.2.1 as their default gateway. As an alternative, manual routes can be entered in each host's routing table. The speednet radio from subnet 2 must have a static route to subnet 1, using the speednet radio from subnet 1 as the gat...

  • Page 12: Installation

    Installation regulatory information fcc warning this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference and 2) this device must accept any interference received, including interference that may cause ...

  • Page 13: Installation

    Installation antenna cable requirements (need the s&c part numbers) speednet radios must be installed by a professional, in order to comply with fcc part 15 radiated power limits. Only antennas supplied by s & c electric company may be used with the speednet radios. The fcc mandates that effective i...

  • Page 14: Installation

    Installation interface pinouts the rs-232 interface of the speednet radio is configured as data communications equipment (dce). Pin function description 1 nc no connection 2 txd rs-233 transmit 3 rxd rs-233 receive 4 nc no connection 5 gnd signal ground 6 nc no connection 7 cts clear to send 8 rts r...

  • Page 15: Installation

    Figure 5. Speednet radio ethernet interface pinout (rj-45). Pin function description 1 txd+ transmit 2 txd- transmit 3 rxd+ receive 4 nc no connection 5 nc no connection 6 rxd- receive 7 nc no connection 8 nc no connection need types of installation inserted here: ir internal repeater - pole - stree...