Summary of SUPER SMART
Page 1
Super smart super smart diesel ® use and maintenance manual gb.
Page 3: Reversible Two-Wheel Tractor
Gb reversible two-wheel tractor super smart super smart diesel before using the two-wheel tractor carefully read the instructions given in this manual.
Page 4
Gb 2 table of contents page page introduction.................................................... 3 safety regulations ....................................... 3 general notices............................................. 3 starting the engine ...................................... 4 operating of th...
Page 5
3 introduction • this manual provides use and maintenance in- structions, technical specifications, and safety pre- cautions for reversible two-wheel tractor: − model super smart in the versions with gasoline engine. • the first section of this manual provides technical specifications and gives inst...
Page 6
4 starting the engine • disengage all control levers before starting the mo- tor. Keep your feet clear of the attachments fitted to the two-wheel tractor. • do not run the engine in a closed ambient where the exhaust gases can collect. They contain car- bon monoxide that is highly toxic. • do not in...
Page 7
5 • keep your two-wheel tractor clean. Do not let grass and oil residues build up: these are a fire hazard. • fuel is highly flammable. Store fuel only in spe- cifically designed containers. Refuel your two- wheel tractor in the open. Do not smoke while re- fuelling. • complete refuelling before sta...
Page 8
6 modello tipo: n. Serie: mot.: potenza: kw/ rpm anno di fabbricazione: massa: kg super smart lga 226 4 3600 70,000 bh10x00000 engine: lombardini lga 226 cm. 50 mass (weight): with wheels 3.50-6 with rotary tiller 83,5 81,5 test conditions - p.T.O.: disengaged - machinestationary on a concrete plane...
Page 9
7 technical specifications engine the two-wheel tractor may be fitted with the following engines: − honda gc 160; 4 stroke gasoline engine; 3,7 kw (5 cv); 160 cm 3 . − lombardini lga 226; 4 stroke gasoline engine; 4 kw (5,4 cv); 220 cm 3 . − yanmar l48; 4 stroke diesel engine; 4 kw (5,4 cv); 212 cm ...
Page 10
8 2 mt1002-1gb motor-mower two-wheel tractor 490 1450 680 370 ÷ 400 950 ÷ 960 460 670 1500 830 ÷ 960 820 ÷ 1080 470 370 ÷ 400 safety devices the two-wheel tractor is fitted with the following safety devices to ensure maximum safety: − automatic pto disengagement device. This is a mechanical device t...
Page 11
9 transfer printing - instructions and safety please find below the adhesive transfer printing shown on the machine. For accident prevention purposes, they must always be clearly readable. Should they be damaged, it is compulsory to replace them by requesting the origi- nal spare part from the manuf...
Page 12
10 two-wheel tractor controls see fig.4. 1. Clutch lever. 2. Engine stop lever. 3. Gear lever. (note 2) 4. Handlebar vertical lock release lever. 5. Handlebar sideway lock release lever. 6. Pto control lever. (note 1). 7. Throttle control lever. 8. Attachments instant adaptor. Note 1: when the machi...
Page 13
11 warning a safety device does not permit reverse speed to be engaged when the pto is operating (rotary tilling) power take off (pto) control lever (two- wheel tractor configuration) caution when using the machine as a motor mower, the han- dlebars must be rotated through 180. The gear selec- tor a...
Page 14
12 with respect to when the machine is used as a motor- mower. This is due to reversal of the direction of motion. Lever (fig. 9, item 1) becomes the gear lever, and lever (2) becomes the pto control lever. The symbols shown in figure 9 and applied to the column, remind the user about the functions ...
Page 15
13 fitting front-mounted attachments before fitting a front-mounted attachment (cutter bar mower, rotary mower, snow thrower, etc.), adjust the reverse speed safety device as required, reverse the handlebars and the wheels. Caution super smart diesel model does not allow the use of front attachment....
Page 16
14 coupling attachments to the pto the pto is fitted with an instant adaptor device to fit attachments quickly and easily. Proceed as follows to fit your attachments (see fig. 15): a. Check that lever (1) is in disengaged position. B. Push the shaft of the attachment into the pto (2). Make sure that...
Page 17
15 checks and adjustments clutch lever the clutch lever must have a free play of about 5 to 6 mm before the clutch starts to disengage. Insufficient play can cause clutch slip, while excess play can lead to failure to disengage fully. Adjust play by means of cable adjuster (see fig. 18, item 1)..
Page 18
16 rotary tiller warning • do not use the rotary tiller without the hood. • do not proceed to tilling in proximity of children and/or animals. • keep your hands and feet clear of the tiller at- tachment when the motor is running. Stop the en- gine before touching the tiller for any reason. • make su...
Page 19
17 each tilling element, and by removing or adding one tiller rotor at the end of the two tillers. Refer to fig. 2 to determine the tiller rotor configura- tion required to obtain the desired tilling width, then proceed as follows. To reverse the position of the outside tiller rotor pairs (fig. 3, i...
Page 20
18 rotary tiller maintenance after the first 50 hours (running in) a. Check that all nuts and bolts are secure. Tighten if necessary. B. Change the oil in the tiller drive unit as follows. Remove plug (fig. 6, item 1) and turn the attach- ment upside down to drain out the exhausted oil. Return the a...
Page 21
19 cutter bar mower warning • when you transport your machine, and when you finish work, always fit the knife guard over the cut- ter bar. • keep your hands and feet clear of the cutter bar when in motion. • do not operate the mower in proximity of children and/or animals. • stop the engine before c...
Page 22
20 cutter bar mower technical specifications mechanical con-rod drive − sickle bar mowers cutting width: 95cm. − e.S.M. Bar mowers cutting width: 97cm. Sickle bar mower with cam mechanism a. Mulching bar mowers cutting width: 90cm. Operating cutter bar mowers the cutter bar attachment is driven via ...
Page 23
21 cutting height adjustment proceed as follows to adjust cutting height.(fig.3) a. Loosen the two nuts (1) and (2) that secure each of the two support slides b. Regulate the two support slides (3) until the blade is at the desired height c. Tighten the nuts (1) and (2) again on the two sup- port sl...
Page 27
Ec certificate of conformity according to ecc 89/392 directives and successive modifications declare on their own responsibility, that the machine conforms to the basic safety and health requirements as stated in , and successive modifications. In order to verify the correct application of the afore...
Page 28
Edizione giugno 2006 cod .218258 m3 ® valpadana s.P.A. Società unipersonale appartenente al gruppo industriale argo s.P.A. 42018 s. Martino in rio (re) italy via don pasquino borghi, 6 tel. 0522 73.17.11 - fax 0522 73.17.31 e-mail: infosep@sep.It - http://www.Sep.It.