Saab 9-3 5d m06- 900 installation instructions scdefault monteringsanvisning · installation instructions montageanleitung · instructions de montage sitdefault saab 9-3 5d m06- parking assistance (spa) accessories part no. Group date instruction part no. Replaces 32 025 603 9:40-05 sep 05 32 025 604 ...
2 32 025 604 saab 9-3 5d m06- 1 spa control module 2 holder (x4) 3 seal (x4) 4 distance sensor (x4) 5 protective shell, bumper 6 wiring harness, distance sensor 7 wiring harness, rear harness 8 cable tie (x4) f930a404 1 5 7 6 2 3 4 8.
32 025 604 3 saab 9-3 5d m06- 1 turn the ignition key to the off position and remove the key. 2 raise the car. 3 remove the spoiler's centre nuts. 4 remove the screws to the wheel housing. 5 lower the car and open the tailgate. 6 insert a screwdriver in the hole to reach under the catch for the bump...
4 32 025 604 saab 9-3 5d m06- 7 pull the bumper shell away from the holders. 8 release the catches using a screwdriver. Detach the shell from the moulding. 9 lift off the bumper shell. Important place the bumper on a soft, clean surface. F930a406 8 9 7.
32 025 604 5 saab 9-3 5d m06- 10 pull the cellular block from the bumper shell lugs. 11 remove the protective corner mouldings and the protective shell by inserting tool 82 93 474 under the shell to release the clips. F930a407 11 10 11 11 11.
6 32 025 604 saab 9-3 5d m06- 12 fit the seals to the sensors. 13 fit together the distance sensors and the holders. 14 fit the distance sensors in the bumper shell. Turn the connector in the right direction, see illustration. 15 connect the kit's wiring harness to the sensors and pull it along the ...
32 025 604 7 saab 9-3 5d m06- 16 fit the cellular block by guiding it in toward the bumper shell lugs. Press the cellular block in. 17 fit the protective shell by pressing in the clips. Make sure that the sensors are located correctly. 18 check that all the clips are secured in the bumper shell. F93...
8 32 025 604 saab 9-3 5d m06- 19 fold down the rear seat backrests. 20 remove the left and right-hand c-pillar trim. Use 82 93 474 removal tool to remove the cover plate. 21 remove the left and right-hand side bolsters. Use 82 93 474 removal tool to remove the clips. F930a410 20 20 20 21 21 21.
32 025 604 9 saab 9-3 5d m06- 22 remove the luggage compartment floor. 23 cars with subwoofer: lift up the subwoofer. 24 remove the scuff plate's clips using 84 71 179 removal tool, clips and lift up the scuff plate. F930a411 24 24 22 22.
10 32 025 604 saab 9-3 5d m06- 25 steps 25-33 must be carried out on both the left and right-hand sides. Remove the clip from the mounting in the body. Use a screwdriver. 26 remove the two-stage rivet using 84 71 179 removal tool, clips. 27 remove the mounting for the cargo guard (if fitted). 28 rem...
32 025 604 11 saab 9-3 5d m06- 34 remove the connector for the rear harness (blue and grey) from the electrical centre. 35 remove the car's rear harness and fit the wiring harness from the kit instead. Plug the connec- tors to the electrical centre last of all. 36 fit the kit's control module on the...
12 32 025 604 saab 9-3 5d m06- 37 steps 37-45 must be carried out on both the left and right-hand sides. Fit the foam block and its clips. 38 fit the luggage compartment lighting. Right-hand side: also plug in the connector to the 12 v socket. 39 press the side trim into its clips. 40 fit the cover ...
32 025 604 13 saab 9-3 5d m06- 46 fit the scuff plate. 47 cars with subwoofer: lower the subwoofer and screw it in. 48 fit the luggage compartment floor. F930a415 46 46 48 48.
14 32 025 604 saab 9-3 5d m06- 49 fit the left and right-hand side bolsters. Check that the belt is not twisted. 50 fit the left and right-hand c-pillar trim. 51 fold up the backrests. F930a416 50 50 50 49 49 49.
32 025 604 15 saab 9-3 5d m06- 52 lift the bumper shell and thread in the wiring harness. Fit the rubber grommet. 53 guide the bumper shell's tabs in under the holders. 54 position the bumper shell's front corner between the wing liner and holder. Make sure that the shell lug is between the wing lin...
