- DL manuals
- Saab
- Automobile Accessories
- 32 025 907
- Installation instructions manual
Saab 32 025 907 Installation instructions manual - page 14
14 32 025 872
Saab 9-3 4D/5D M03-
30 Fit the front cover.
31 Fit the rear cover.
32 Align the A-pillar trim in position. Take care not
to damage the inflatable curtain.
33 Fit the retaining screw.
Tightening torque:
5 Nm (4 lbf ft).
WARNING
Take care not to damage the inflatable curtain.
Damage could result in the inflatable curtain not
providing the intended protection to the occupants
in the event of a collision.
F930A533
32
F930A531
30
F930A532
31
F930A534
5Nm
(4lbf ft)
33
Summary of 32 025 907
Page 1
900 installation instructions scdefault monteringsanvisning · installation instructions montageanleitung · instructions de montage sitdefault saab 9-3 4d/5d m03-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3 saab 9-5 m01- . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 2
2 32 025 872 f930a488 1x 1x 1x 1x 1x 1x 11x.
Page 3
32 025 872 3 saab 9-3 4d/5d m03- saab 9-3 4d/5d m03- 1 ignition in off position. 2 remove the floor console’s right-hand side piece. 3 remove the lower glove box screws. 4 remove the inner glove box screws. F930a491 3 f930a489 1 f930a490 2 c a b b f930a492 4.
Page 4
4 32 025 872 saab 9-3 4d/5d m03- 5 unplug the connector for the glove box lighting (a). Cars with acc: remove the coolant hose from the glove box (b). 6 remove the cover plate from the a-pillar trim. 7 remove the retaining screw. 8 grip the upper edge of the a-pillar trim and care- fully pull out an...
Page 5
32 025 872 5 saab 9-3 4d/5d m03- 9 remove the rear cover. 10 remove the front cover. 11 remove the screws. 12 remove the centre cover. F930a499 11 f930a497 9 f930a498 10 f930a500 12.
Page 6
6 32 025 872 saab 9-3 4d/5d m03- 13 cars with rain sensor: remove the cover. 14 fit the adhesive tape onto the microphone. 15 fit the microphone. 16 insert the microphone cable through the hole in the headlining by the roof console. F930a503 15 f930a501 13 f930a502 14 f930a504 16.
Page 7
32 025 872 7 saab 9-3 4d/5d m03- 17 route the microphone cable on under the head- lining towards the windscreen. Press in the cen- tre cover and draw the microphone cable tight at the same time. 18 route the microphone cable under the headlin- ing. 19 secure the microphone cable to the a-pillar. 20 ...
Page 8
8 32 025 872 saab 9-3 4d/5d m03- fit the keypad in accordance with one of the alterna- tives. F930a509 22.1-22.5 21.1-21.7.
Page 9
32 025 872 9 saab 9-3 4d/5d m03- 21 fitting the keypad, alternative 1: 21.1 remove the ashtray/storage compart- ment. 21.2 remove the acc panel. 21.3 fit the keypad to the console and mark out the cable route. 21.4 cut out from the console for the cable. F930a513 21.3 f930a511 a 21.1 b f930a512 b a ...
Page 10
10 32 025 872 saab 9-3 4d/5d m03- 21.5 fit the keypad to the console. 21.6 route the cable down behind the radio down towards the air bellows and secure it. 21.7 fit the acc panel (a). Check that the key- pad’s cable is located in the groove. Fit the ashtray/storage compartment (b). Important secure...
Page 11
32 025 872 11 saab 9-3 4d/5d m03- 22 fitting the keypad, alternative 2: 22.1 remove the cover. 22.2 route the cable along the right-hand side, down towards the air bellows. 22.3 route the cable in the dashboard’s groove. 22.4 fit the cover. F930a520 22.3 f930a518 a b 22.1 f930a519 22.2 22.4 f930a521...
Page 12
12 32 025 872 saab 9-3 4d/5d m03- 22.5 fit the keypad and adjust any excess cable length. 23 connect the control module (a), microphone (b) and keypad (c) to the adapter harness. 24 secure the control module using two cable ties to the panel member. 25 release the tele1 connection from the car’s cab...
Page 13
32 025 872 13 saab 9-3 4d/5d m03- 26 connect the adapter harness to the car’s tel 1 connection and secure the wiring. 27 secure the wiring to the panel member. 28 cars with rain sensor: fit the cover. 29 fit the screws to the cover. Important secure the wiring harness firmly so that there is no risk...
Page 14
14 32 025 872 saab 9-3 4d/5d m03- 30 fit the front cover. 31 fit the rear cover. 32 align the a-pillar trim in position. Take care not to damage the inflatable curtain. 33 fit the retaining screw. Tightening torque: 5 nm (4 lbf ft). Warning take care not to damage the inflatable curtain. Damage coul...
Page 15
32 025 872 15 saab 9-3 4d/5d m03- 34 fit the cover plate to the a-pillar trim. 35 plug in the connector for the glove box lighting (a). Cars with acc: fit the coolant hose for the glove box (b). 36 fit the inner glove box screws. 37 fit the lower glove box screws. F930a537 36 f930a535 34 f930a536 35...
Page 16
16 32 025 872 saab 9-3 4d/5d m03- 38 fit the floor console’s right-hand side piece. F930a539 38 a c b.
Page 17
32 025 872 17 saab 9-5 m01- saab 9-5 m01- 1 ignition in off position. 2 remove the radio/navigation unit, m01-05: 2.1 insert the special tools into the intended holes until the tools engage and pull out the unit. 2.2 remove the compartment. 2.3 unplug the connectors. E930a429 m01-05 2.2 e930a427 1 e...
Page 18
18 32 025 872 saab 9-5 m01- 3 remove the radio/navigation unit, m06- 3.1 remove the plugs and remove the screws. 3.2 pull the unit out and unplug the connectors and disconnect the antenna connection. 4 remove the acc panel. E930a433 4 a b 3.1 e930a431 m06- e930a432 m06- 3.2.
Page 19
32 025 872 19 saab 9-5 m01- 5 remove the lower section of the dashboard on the driver’s side: 5.1 remove the data link connector (a) 5.2 remove the lower panel (b). 5.3 remove the clip (c). 5.4 remove the floor lighting (d). E930a434 c b b a d b 5.
Page 20
20 32 025 872 saab 9-5 m01- 6 remove the cover to the fuses. 7 remove the a-pillar trim (secured with clips). Remove the upper clip (a) from the trim. 8 remove the sun visor’s screws and allow the sun visor to hang down. 9 remove the glass cover (a), the retaining screw (b) and lower the cover. Warn...
Page 21
32 025 872 21 saab 9-5 m01- 10 fit the adhesive tape to the microphone. 11 press the microphone in on the outside of the cover, beside the car’s original microphone. 12 route the microphone cable up, under the headlining and on, down around the a-pillar. 13 secure the microphone cable up against the...
Page 22
22 32 025 872 saab 9-5 m01- 14 press the cover in, fit the retaining screw (b) and the glass cover (a). E930a443 14 a b.
Page 23
32 025 872 23 saab 9-5 m01- 15 route and secure the microphone cable: route the cable under the panel, towards the centre console and in behind the radio/naviga- tion unit secure the cable under the panel. Important secure the wiring harness firmly so that there is no risk of chafing and rattling. E...
Page 24
24 32 025 872 saab 9-5 m01- 16 remove the cover for the heating and ventila- tion unit. 17 fold aside the floor carpet. 18 cars with diesel engine: 18.1 remove the sound absorber. 18.2 cut out the top insulation layer. E930a448 18.1 e930a446 16 e930a447 17 e930a445 18.2.
Page 25
32 025 872 25 saab 9-5 m01- 19 position the adapter harness. 20 connect the control module to the adapter har- ness. 21 align the control module and secure the wiring. 22 cars with diesel engine: fit the sound absorber. Important secure the wiring harness firmly so that there is no risk of chafing a...
Page 26
26 32 025 872 saab 9-5 m01- 23 refit the floor carpet. 24 fit the cover for the heating and ventilation unit. 25 cut the tape around the tele1 connection on the car’s wiring harness. 26 connect the adapter harness to the car’s tele1 connection. E930a455 25 e930a453 23 e930a454 24 e930a456 26.
Page 27
32 025 872 27 saab 9-5 m01- 27 connect the adapter harnesses. E930a457 27.
Page 28
28 32 025 872 saab 9-5 m01- fit the keypad in accordance with one of the alterna- tives. E930a458 29.1-29.4 28.1-28.14.
Page 29
32 025 872 29 saab 9-5 m01- 28 fitting the keypad, alternative 1: 28.1 remove the storage compartment (a). 28.2 automatic transmission: remove the surround (b). 28.3 manual gearbox: lift up the gear lever gaiter (c). 28.4 remove the cover’s screws (d) and unplug the connector (e). Important this loc...
Page 30
30 32 025 872 saab 9-5 m01- 28.5 measure out the keypad location and drill a 3 mm hole. 28.6 cut/drill a groove straight out. 28.7 connect the keypad to the adapter har- ness. 28.8 secure the wiring. E930a463 28.7 e930a461 30mm (1.2in) 3mm (0.1in) 20mm (0.8in) 28.5 e930a462 28.6 e930a459 28.8.
Page 31
32 025 872 31 saab 9-5 m01- 28.9 plug in the connector (e) and fit the cover’s screws (d). 28.10 manual gearbox: fit the gear lever gaiter (c). 28.11 28.12fit the storage compartment (a). E930a464 a a b c d e 28.9-28.12.
Page 32
32 32 025 872 saab 9-5 m01- 28.13secure the keypad’s wiring harness. 28.14fit the keypad. Important secure the wiring harness firmly so that there is no risk of chafing and rattling. E930a465 28.13 e930a466 28.14.
Page 33
32 025 872 33 saab 9-5 m01- 29 fitting the keypad, alternative 2: 29.1 carefully prize out the switch panel and route the keypad cable between the switch panel and the dashboard. 29.2 fit the keypad. 29.3 connect the keypad to the adapter har- ness. 29.4 secure the wiring. E930a469 29.3 e930a467 29....
Page 34
34 32 025 872 saab 9-5 m01- 30 secure the wiring together with the car’s wiring harness. 31 fit the sun visor’s screws. 32 fit the lower section of the trim in place, fit the clip (a) with the loop down in the trim and press the trim into all of the clips. 33 fit the cover to the fuses. Important se...
Page 35
32 025 872 35 saab 9-5 m01- 34 fit the lower section of the dashboard: 34.1 connect the floor lighting (d). 34.2 fit the clip (c). 34.3 fit the lower panel (b). 34.4 fit the data link connector (a) e930a475 c b b a d b 34.
Page 36
36 32 025 872 saab 9-5 m01- 35 fit the acc panel. 36 fit the radio/navigation unit, m01-05: 36.1 plug in the connectors. 36.2 fit the compartment. 36.3 insert the unit. 36.2 e930a478 m01-05 e930a476 35 e930a477 m01-05 36.1 e930a479 m01-05 36.3.
Page 37
32 025 872 37 saab 9-5 m01- 37 fit the radio/navigation unit, m06- 37.1 plug in the connectors. 37.2 insert the unit, fit the screws and the plugs. E930a480 m06- 37.1 37.2 e930a481 m06-.