1. DL manuals
  2. Saeco
  3. Coffee Maker
  4. D.A. COMBISNACK
  5. Use And Maintenance

Saeco D.A. COMBISNACK Use And Maintenance

Manual is about: Vending machine ACCESSORIES AND PAYMENT SYSTEMS

Summary of D.A. COMBISNACK

  • Page 1

    Accessories and payment systems d.A. Combisnack vending machine u se a n d m a in te n a n ce type: d.A. Combisnack espresso italia u se a n d m a in te n a n ce u se a n d m a in te n a n ce ltd u se a n d m a in te n a n ce www.Espressoitalia.Com.Au freecall 1300 660 976.

  • Page 2: Contents

    2 english contents 1 - diagram of connections to the keypad board/cpu: . ................................................. 3 2 - payment system installation . ............................................................................................. 4 3 - payment system feeder kit . ................

  • Page 3

    3 english fig. 1 1 - diagram of connections to the keypad board/cpu: 1. Mdb systems; 2. Bdv, mdb and executive system power supply; 3. 24 v dc / 12 v dc banknote reader; 4. Executive and bdv systems; 5. 24 v dc parallel coiner (non-change giving); 5. 12 v dc parallel coiner (non-change giving) with ...

  • Page 4

    4 english a b c d e this vending machine is supplied with panels assembled as shown in fig. 2. It is possible to change and replace them with those provided by saeco according to the customer’s requirements. - panel for otr. And m.Ivo banknote readers - panel for jcm banknote reader - panel for smil...

  • Page 5

    5 english - unplug the four-pin connector from the cpu card (fig. 6). - connect the two-pin connector (ref. C, fig. 3) to the payment system power supply board. Connect the 2 contacts of the other end to the 2 free slots of the 4-pin connector that was previously unplugged from the cpu card (fig. 7)...

  • Page 6

    6 english - connect the four-pin connector to the cpu card (fig. 8). Fig. 8 - close the vending machine upper door. The mains voltage values provided by this feeder can also be found on cn6 (ref. 3, fig. 1) and cn9 (ref. 8, fig. 1) connectors of cpu card. Connector description voltage pin cn6 connec...

  • Page 7

    7 english installation - remove the machine rear panel (fig. 10) by untightening the screws and disconnecting the ground wiring placed on the machine. A b c d e n p r g h 4 - independent tank kit this kit allows the vending machine to be supplied by means of an internal tank instead of by the water ...

  • Page 8

    8 english - carry out all the electric connections as indicated by the diagram below. - disconnect the two power supply wirings from the water inlet solenoid valve (fig. 14). - remove the water inlet solenoid valve (fig. 15). - tighten the relay and support plate (ref. R, fig. 9) by using the screws...

  • Page 9

    9 english 24 v d.C. Inlet solenoid valve red dark blue power supply wirings inlet solenoid valve power supply wirings fan motor blue red blue red 230v 50hz dark blue dark blue dark blue dark blue dark blue relay pink pink pink pink pink pump 1 fan - reassemble the machine rear panel taking care to r...

  • Page 10

    10 english 5 - float kit it allows the display to read the discharge fluid maximum level. In this condition, no hot beverage is available and the display will read “error 09”. The float can be installed in different positions according to whether the machine is connected to a water network (22 l tan...

  • Page 11

    11 english 1 fig. 33 fig. 34 access the machine programming menu and set “yes” in the “tank” menu (fig. 34) to enable the display reading of the discharge fluid maximum level. In order to properly carry out this operation, disable the safety device and press key 1 (fig. 33) to access the programming...

  • Page 12

    12 english vm code 0000 stop 6 - pulse counter kit the vending machine can be fitted with an electromechanical pulse counter (24v dc) which will count the number of coffees or the total beverages brewed by the machine. Assembly kit (fig. 35) a. 1 pulse counter with support b. 2 screws a b fig. 35 fi...

  • Page 13

    13 english 7 - water solenoid valve kit it is possible to brew hot water alone by installing the required kit assembly kit (fig. 39) a. 1 water pipe set b. 1 or, pipe clamp and 1/8" h4,5 nut c. 1 two-way solenoid valve fig. 39 installation - remove the machine rear panel (fig. 40) by untightening th...

  • Page 14

    14 english - screw the nut and fix the or (ref. B, fig. 39) on the 2-way solenoid valve (ref. C, fig. 39). Remove the block support from its seat and screw the solenoid valve in the hole (fig. 45) previously cleared from its cap (fig. 41). The solenoid valve must be placed with fastons upwards reins...

  • Page 15

    15 english 8 - sugar coil kit this kit allows the sugar door opening only when required, since an electromagnet controls it. This prevents any sugar grain from accidentally falling when the “without sugar” option has been selected. Assembly kit (fig. 50) a. 1 two-pin connector b. 1 connecting rod c....

  • Page 16

    16 english fig. 59 - assemble the whole unit on the sugar stirrer dispenser (fig. 57) - couple the connector (ref. A, fig. 50) with the electromagnet by means of the fastons. Insert the other end in the connection located on the mounting plate (fig. 58). - reinstall the sugar channel and fix it with...

  • Page 17

    17 english 9 - saeco card assembly kit assembly kit (fig. 60) a. 1 adhesive sheet for drilling b. 1 guard for universal module c. 1 flat cable d. 4 screws and 4 spacers for card e. 1 saeco card external antenna fig. 60 f a b c d e fig. 61 fig. 62 fig. 63 - open the upper front door. - loosen the gua...

  • Page 18

    18 english fig. 66 fig. 67 fig. 68 fig. 69 - fasten the universal module by means of the 4 screws and spacers (ref. D, fig. 60) on the door (fig. 66). - connect the universal module to the i/o card (fig. 67) by means of the flat cable (ref. C, fig. 60). - connect the antenna cable to the universal m...

  • Page 19

    19 english 9.1 - saeco card programming the saeco card module presence (automatically detected by the v.M.) adds the following entries to the payment system programming menu entry description: recharge - it allows disabling or enabling any saeco card recharge operations. By setting recharge = no the...

  • Page 20

    20 english installation - insert the lever under the vending machine. Rotate the lever to lift the machine (fig. 71 and 72). The lever position shall allow the carriage set to be subsequently inserted. - insert the carriage set under the v.M. (fig. 73), move the lever back to its initial position, t...

  • Page 21

    21 english fig. 82 fig. 83 11 - brita purifier kit it is possible to install a filter, manufactured by brita company, on the vending machine, in order to decalcify water and eliminate all unpleasant smells. Assembly kit (fig. 79) a. 2 fittings b. 1 cover for filter cartridge support c. 1 filter cart...

  • Page 22

    22 english fig. 87 fig. 88 - insert the spring (ref. I, fig. 79) into the pipe (ref. M, fig. 79) and the latter into the air break fitting (fig. 87). - insert the other spring (ref. L, fig. 79) into the pipe free end (ref. H, fig. 79) and the latter (fig. 88) into the upper fitting of the cartridge ...

  • Page 23

    23 english 12 - rs 232 interface box the rs232 interface box allows connecting the automatic vending machine to a pc, in order to transfer statistic data. Assembly kit (fig. 91) a. 1 ttl-rs232 level adapter fig. 91 a b c installation - insert the flat cable (ref. B., fig. 91) on the machine cpu rele...

  • Page 24

    24 english 13 - saeco water softener support this support allows fixing the water softener supplied by saeco in a proper way. Assembly kit (fig. 92) a. 1 water softener support b. 1 water softener c. 4 screws fig. 92 a b installation - remove the machine rear panel and assemble the water softener su...

  • Page 25

    25 english the allowable operations are the following: display message operation notes data transfer copy vmc ==> key copy of vending machine data on the key this operation is always possible. Data transfer copy key ==> vmc copy of key data on the vending machine this operation is only possible if t...

  • Page 26

    26 english price value prezzo 001: 50 price value price 002: 250 price value price n: 550 beverage prices normal beverage prices diff 1 beverage prices diff 2 beverage prices card set global set single global 001:200 abcdefghi global nnn:500 abcdefghi single 001:200 abcdefghi single nnn:500 abcdefgh...

  • Page 27

    27 english 16.2 - time keeper functions in the maintenance menus statistic with this function you can display all sales statistics accounted by the vending machine. Vm code assigned by the operator. Coins total the total value of the inserted coins is displayed. Banknote total the total value of the...

  • Page 28

    C od . 0 8 7 5 .9 7 8 - e d° 0 1 0 2 /0 3 espresso italia pty ltd www.Espressoitalia.Com.Au freecall 1300 660 976.