- DL manuals
- Saeco
- Coffee Maker
- Modular Coffee
- Instruction And Maintenance Manual
Saeco Modular Coffee Instruction And Maintenance Manual
Summary of Modular Coffee
Page 1
Saeco automatic espresso coffee machine instruction and maintenance manual.
Page 2
Table of contents table of contents…………………………………..2 main parts………………………………………………3 1-introduction to manual …………………….4 1.1 foreword…………………………………..4 1.2 symbols used ……………………………4 2-machine information………………………….4 2.1 notes for the user………………………... 4 2.2 intended use of the machine……………4 2.3 residua ri...
Page 3
English main parts 1 left hand side panel 9 rubber protector 2 glass 10 main switch 3 back cover panel 11 hot water spout (luxe version) 4 cup heating plate 12 steam selection knob (luxe version) 5 right hand side pane 13 front door 6 pre-ground coffee slot 14 rubber protector 7 coffee beans hopper ...
Page 4
1 - introduction to manual 1.1 foreword important this manual is an integral part of the machine and must be carefully studied. It contains 'information relative to the correct use of the machine and to its maintenance (strictly concerning user operations). The document refers to the modular machine...
Page 5
English 2.4 machine identification the machine is identified by the model name and serial number to be found on the id plate (fig. 2). The plate carries the following specifications: • name of manufacturer • ce marking • machine model • serial number • year of manufacture • several manufacturing det...
Page 6
Danger it is forbidden for the user to carry out operations that are indicated in this publication as being the responsibility of the maintenance technician. 3.3 safety devices installed - three safety valves protect the machine from over- pressures in the network meant for producing hot water for c...
Page 7
English 4.3 coffee dispenser unit the position of this unit (ref. 21, fig. 4) can be modified according to the height of the container used. In fact it is possible to move the mobile dispenser backwards (ref. 23, fig. 4) and the telescopic dispenser upwards or downwards (ref. 24, fig. 4). This allow...
Page 8
Important in order to make connection operations easier, the diameter of the holes to be drilled in the surface top will have to be greater than that of the pipes and cables indicated in the legend of fig. 6. Legend: a' adjustable feet b' water drain (27 mm 0 tube) c' water supply (19 mm 0 tube) d' ...
Page 9
English important it strongly suggested that the machine be supplied with water treated through a descaling device, especially in cases of water with a high content of calcium and magnesium salts (hard water). 5.2 insertion of nation key danger operation falling within the competence of the maintena...
Page 10
Important before operating the machine it is necessary to have read this publication carefully and to have gained a good general knowledge of the machine. After a period of inactivity of the machine it is advisable to read again chapter "5.3 before re-utilizing the machine. 6.1 machine statuses conc...
Page 11
English 6.7 light coffee dispensing this type of dispensing is performed by utilizing doses of pre- ground coffee manually introduced into the machine through the pre-ground coffee slot (ref. 6, fig. 1). To the quantity thus provided manually the machine autonomously adds a small dose of ground coff...
Page 12
All the dispensing keys and are equipped with a self-learning memory. Once they are programmed, they supply the same drink quantity at every subsequent command. Their programming is obtained as follows: - machine on and ready for use; - container positioned under the dispenser; - press and hold down...
Page 13
English 6.13 display messages a series of messages in addition to those already found in the previous paragraphs, can be shown on the machine's display (ref. 8a,fig. 1). Standby: it appears when the machine is off (with main switch in position "i") with the function of automatic switching on / switc...
Page 14
English - the blinking cursor is positioned under the value to be modified. - press keys (up) or (down) to modify the value. - confirm the datum modified with key (enter). 14 6.14.1 summary of menu programmable functions 6.14.2 functions description the outlining of functions continues on following ...
Page 15
English language - if the "nation key" foresees the use of more than one language on display, by using from the" language " menu, access can be gained to their selection. - if the "nation key" foresees a single language, by pressing no other selection is accessed. Cupwarmer - by confirming" on ", th...
Page 16
Rinsing programm this function allows the dispensing of a minimum quantify of hot water (abt 5 cc) by the machine to prevent sediments in the coffee dispenser from forming; this wash is automatically carried out after a programmed time lapse (20 to 240 minutes) from the last dispensing of coffee. - ...
Page 17
English on/off time this function allows the programming of the machine's automatic switch-on/off times for the whole of a weekly time span. - by confirming " on/off time ", the cursor will be posi- tioned on the day to be modified. - program the day with key (down), thus shifting the letter from up...
Page 18
English - assemble the cup heating plate (ref. 4, fig. 11 by inserting the electrical connector info the electronic board properly, the fitting into the drain tube (ref. B, fig. 11, and by connecting the earth cable. - manually rotate the studs (ref. A, fig. 11) so as to place the milling horizontal...
Page 19
English 7.2.1 coffee dispenser the following can be dismantled: - the top cover (ref. A, fig. 12), of the fixed dispenser (ref. F, fig. 12), by pulling it upwards; - the rubber gasket (ref. H, fig. 12); - the mobile dispenser (ref. G, fig. 12) by pulling it downwards; - the telescopic dispenser (ref...
Page 20
It will then be necessary to open the coffee grinder unit (ref. 19, fig. 1) and remove the cause of the jamming. - with the help of a vacuum cleaner remove the beans from the grinder's inlet (fig. 16). 7.3.1 coffee grinder dismantling/assembly in order to dismantle the coffee grinder the following s...
Page 21
English important this last operation is necessary both to avoid the jamming and to prevent damaging the grinders. - re-position the geared wheel (ref. D, fig. 20) and lock if by tightening the screws (ref. C, fig. 20). - secure the hopper (ref. 7, fig. 21) by hand-tightening the screws (ref. B, fig...
Page 22
English 8 - troubleshooting -causes and remedies the following table lists a number of troubles that may occur dur- ing the working life of the machine. When the symbolappears in the "remedy" column it means that the intervention must be carried out by the maintenance technician. Trouble cause remed...