Saeco Primea Ring Operation And Maintenance Manual - Display

Summary of Primea Ring

  • Page 1

    Operation and maintenance manual before using the machine, please read the attached operating instructions. Carefully read the safety rules for household use only.

  • Page 2

    Important safeguards when using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. Do not touch hot surfaces. Use handles or knobs. 3. To protect against fire, electric shock and injury to persons do not immerse cord, plug...

  • Page 3

    Caution this appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service centre. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no parts inside the...

  • Page 4: Index

    2 index warning ......................................................................................................................................2 appliance ....................................................................................................................................4 acce...

  • Page 5

    3 the coffee machine is intended for preparing espresso by using either coffee beans or ground coffee. It includes an automatic device for preparing milk beverages and a hot water dispenser. The machine is elegantly designed for domestic use and is not suitable for continuous heavy duty or professio...

  • Page 6: Appliance

    4 cappuccinatore maintenance kit c i t ground coffee measuring scoop cleaning detergent (brew group) water hardness tester grinder adjustment key lubricant for the brew group detergent for cleaning milk container i d t intenza water fi lter accessories control panel sbs appliance compartment for pre-...

  • Page 7: Installation

    5 1 2 3 4 7 6 5 installation attach the female end of the power cord to the machine. Insert the male end into the power outlet. Place a container beneath the hot water spout. Press the button on the coffee hopper to open the cover. Fill the hopper with coffee beans. Close the cover pushing it down c...

  • Page 8: Installation

    6 6 press ok boiler filling press to prime the circuit; wait until the machine stops. 7 warming up please wait 8 rinsing please wait 9 strong aroma espresso coffee 08:33 when the priming is completed, wait until the machine has fi nished the heating phase. Once the heating phase is completed, a small...

  • Page 9

    7 5 6 7 8 9 4 1 3 2 remove the small white fi lter from the tank and store it in a dry place sheltered from dust. Fill the tank with fresh drinking water and reinsert it into the machine. Set the intenza aroma system: a = light water b = medium water (standard) c = hard water for further details see ...

  • Page 10: Display

    8 • press the key twice to make 2 cups. This operation can be performed until the grinding is complete. Press twice by pressing the key, there are three possible selections (strong, medium, mild) that indicate the aroma (coffee quantity to be ground by the machine) for the beverage selected. This ke...

  • Page 11: Adjustments

    9 open the milk compartment by pressing the button and remove the milk container. Remove the cover and pour in the milk. Do not exceed the maximum level shown in the fi gure. Replace the lid on the container and place it back in the milk compartment. Make sure to carefully close the compartment. 2 1 ...

  • Page 12: Beverage Dispensing

    10 1 2 3 the dispensing of coffee, hot water and milk may be stopped at any time by pressing the key again. The dispensed milk may be very hot: danger of scalding. Avoid touching it directly with your hands. Check that all the containers are clean. To do this operation, follow the instructions in th...

  • Page 13

    11 4 1 2 3 5 dispensing beverages with ground coffee pre-ground coffee must be poured into the appropriate compartment positioned next to the coffee bean hopper. Pour in only coffee ground for espresso machines and never coffee beans or instant coffee. (see the “beverage programming” chapter on page...

  • Page 14: Beverage Dispensing

    12 1 2 3 4 5 6 if the user wishes to continue preparing other drinks the machine will keep the “rinsing milk circuit” signal active. After 20 minutes of inactivity, the machine requires the user to perform a rinsing cycle as described in step 7. If the machine is turned off immediately after dispens...

  • Page 15

    13 7 8 9 in this phase the user cannot intervene and must wait until the cycle fi nishes. After this, the machine returns to the main menu. Remove the container, rinse and dry. Rinsing milk circuit in progress milk circ. Rinse cycle press to perform the rinse cycle. This procedure must be performed f...

  • Page 16: Beverage Dispensing

    14 1 2 3 4 5 1 2 3 beverage dispensing espresso macchiato cappuccino when the “milk circuit rinsing” symbol fl ashes, rinse the milk circuits as described for the latte macchiato (see page 12, step 6). Strong aroma espresso coffee 08:33 press the key. Strong aroma espresso macchiato 08:33 select espr...

  • Page 17

    15 4 5 1 2 3 1 2 when the “milk circuit rinsing” symbol fl ashes, rinse the milk circuits as described for the latte macchiato (see page 12, step 6). Brewing in progress cappuccino if you wish, press the button. Once the desired milk quantity has been reached, press the button again. Press the key on...

  • Page 18: Beverage Programming

    16 select the quantity of coffee to be ground (opti-dose), or select pre-ground coffee, and/or set: - coffee temperature - coffee prebrewing by sliding the click wheel with a fi nger you can change the settings for: - the quantity of coffee to be brewed; - the quantity of milk to be dispensed; - the ...

  • Page 19

    17 1 2 4 5 6 7 8 9 10 11 check that the water tank and coffee bean hopper are full; place the cup under the dispensing spout. Press the button. Press the button one or more times to adjust the aroma or select the use of pre-ground coffee. Press the button to save. Select the beverage to be programme...

  • Page 20: Programming The Machine

    18 some of the machine’s functions can be programmed to customize operations according to your own tastes. Strong aroma espresso coffee 08:33 press the key to: - confi rm the selection; - save the new settings. 1 press the key. 2 turn the click wheel with your fi nger to: - select the functions - chan...

  • Page 21

    19 1 2 3 “l anguage” menu machine settings to set the general machine operating parameters, press the key and select “machine settings”. Turn the click wheel with a fi nger to: machine settings language machine settings water filter machine settings water hardness machine settings rinse cycle machine...

  • Page 22: Programming The Machine

    20 1 2 3 1 2 4 3 5 6 “cup warmer” menu machine settings machine settings cup warming plate select by navigating the click wheel with your fi nger. It is possible to set: - always on - always off - off in stand-by > machine settings > cup warming plate. To turn on/off the operation of the cup warming ...

  • Page 23

    21 1 1 2 3 3 4 5 2 1 2 3 4 a b c intenza aroma system machine water hardness setting check the water hardness level obtained from the test. The measurement can be used to set the intenza aroma system correctly (see page 7). Matching parameters are described on the upper part. Immerse the water hardn...

  • Page 24: Programming The Machine

    22 1 2 3 “acoustic al arm” menu machine settings machine settings acoustic alerts > machine settings > acoustic alerts to enable/disable the acoustic alarms of the machine. Acoustic alerts key tone 4 select by navigating the click wheel with your fi nger. You may set: - key tone: to activate/deactiva...

  • Page 25

    23 1 2 3 4 5 “maintenance” menu machine settings maintenance maintenance milk circ. Rinse cycle > machine settings > maintenance. To clean all the machine’s internal circuits used for making coffee and milk. Turn the click wheel with your fi nger to: maintenance milk circ. Rinse cycle maintenance mil...

  • Page 26: Programming The Machine

    24 1 2 3 4 6 5 machine settings maintenance maintenance coffee cleaning cycle coffee wash cycle > machine settings > maintenance > coffee cleaning cycle yes coffee cleaning cycle insert cleaning tablet coffee cleaning cycle insert the tablet as shown above. Press to start. To clean the machine’s int...

  • Page 27

    25 1 2 3 machine settings maintenance maintenance milk cleaning cycle milk wash cycle > machine settings > maintenance > milk cleaning cycle yes milk cleaning cycle to clean the machine’s internal circuits used for preparing milk. This cycle is proposed after 14 days from the fi rst dispensing of a m...

  • Page 28: Programming The Machine

    26 9 8 10 11 fill the milk container with fresh water up to the «max» level. Insert the content of the detergent packet into the container. Open the compartment and insert the container with the detergent. Close the compartment. Press to start. Position an adequately sized container under the milk s...

  • Page 29

    27 14 16 13 15 18 rinse the container and fi ll it with fresh water. Insert the container and press . Wait… when the rinse cycle is fi nished the following appears… remove the milk container. Rinse the container and fi ll it with fresh water. Perform another rinse cycle as shown previously. At the end,...

  • Page 30: Programming The Machine

    28 1 2 saeco descaler is recommended, however you can use a non-toxic and/or non-harmful descaling product for coffee machines, commonly available online or in coffeeshops. The solution used must be disposed of according to the manufacturer’s instructions and/or according to regulations in force in ...

  • Page 31

    29 1 2 3 4 5 6 7 8 9 to perform descaling before the machine blocks, or before the descaling message appears: machine settings maintenance maintenance descaling cycle yes descaling cycle descaling descaling cycle fill water tank descaling cycle insert tank descaling cycle insert the descaler and pre...

  • Page 32: Programming The Machine

    30 1 2 3 4 clock settings > machine settings > clock settings to set the current time, date and hour format to display. Machine settings clock settings in this menu you can set: - the current time (hour and minutes) - the hour format (24 hours - am/pm) - the current date (day – month – year – day of...

  • Page 33

    31 1 2 3 4 5 the machine stores the selected value, returns to the previous screen and enables another parameter to be set. 1 2 3 4 5 the machine also allows displaying the time in the international format (24h). Date setting > machine settings > clock settings > date setting to set the date (day, m...

  • Page 34: Programming The Machine

    32 1 2 3 1 2 3 1. 2. 1. 2. Standby setting > machine settings > stand-by setting stand-by setting energy saving in this menu you can: energy saving > machine settings > stand-by setting > energy saving by default, the off delay is set to 3 hours. Stand-by setting energy saving after 3 hours energy s...

  • Page 35

    33 1 2 2. Setting an interval for turning on the machine 12 3 4 5 6 7 8 9 10 11 stand-by setting timer setting timer setting monday you can set the on/off times for all the days of the week. Monday switch on you can set an on/off time for each day of the week (in this case, the procedure for setting...

  • Page 36: Programming The Machine

    34 1 2 3 4 5 special functions this menu allows you to access special functions present on the machine. To access, press the key and select “special functions”. Turn the click wheel with a fi nger to: special functions cancel settings special functions coffee of the world restore the factory settings...

  • Page 37

    35 1 2 3 4 5 6 prepare true ristretto all’italiana prepare a typical north european coffee prepare a typical french/ swiss coffee prepare a fl avourful latte macchiato without the fear of not being able to sleep prepare a coffee for a day full of energy prepare a typical italian espresso prepare a ty...

  • Page 38: Programming The Machine

    36 1 2 3 4 beverage counters special function product counters > special funtions > product counters this function shows how many beverages have been prepared for every single type of beverage. 23 espresso coffee special function product counters you may display the data of every single type of beve...

  • Page 39: Cleaning and Maintenance

    37 cleaning and maintenance 1 2 3 1 6 5 4 maintenance during operation during normal operation, the “empty grounds drawer” message may appear. This operation must be performed when the machine is on. If you remove grounds with the machine off or when not signaled on the display, the count of the gro...

  • Page 40: Cleaning and Maintenance

    38 cleaning and maintenance the milk container and the cappuccinatore have been designed to optimize the milk froth. Thorough cleaning and maintenance of the milk container and cappuccinatore will allow you to savour excellent milk-based beverages. It is recommended to rinse the cappuccinatore befor...

  • Page 41

    39 remove the cappuccinatore. Thorough maintenance of the cappuccinatore thoroughly wash the cappuccinatore at least once a week. The components should be hand-washed with household detergents. Separate the upper part of the cappuccinatore from the lower part. Remove the regulator. Remove the cap fr...

  • Page 42: Cleaning and Maintenance

    40 1 2 5 6 7 8 9 press to open the service door. The brew group must be cleaned at least once a week. Lubricate the brew group after approximately 500 brewing cycles. The grease for the lubrication of the brew group may be purchased by authorized service centres. Wash the brew group with warm water....

  • Page 43

    41 12 6 5 4 reassemble it by pressing the push! Button. Close the service door and insert the coffee grounds drawer. The grinder can be adjusted in order to create a fi ner grind after many grinder cycles (approximately 2000). Warning! This operation should be carried out carefully and by an experien...

  • Page 44: Error Codes

    42 error codes guide message that appears how to remove the message restart to solving the problem turn off and after 30 minutes turn the machine on again to restore normal operation. Call assistance problem that requires the intervention of the customer service centre. Insert drip tray insert drip ...

  • Page 45: Sos

    43 sos safety rules in case of emergency immediately unplug the cord from the outlet. Only use the appliance • indoors. • for preparing coffee, hot water and for foaming milk. • for domestic use. • this appliance is not intended for use by persons (including children) with reduced physical, sensory ...

  • Page 46: Safety Rules

    44 safety rules dangers • children should be supervised to ensure that they do not play with the appliance. • the appliance is dangerous to children. When left unattended, unplug from the electrical outlet. • keep the coffee machine packaging out of the reach of children. • never direct the jet of h...

  • Page 47: Technical Data

    45 technical data subject to engineering and manufacturing changes due to technological developments. The machine conforms to european directive 89/336/eec (italian legislative decree 476 dated 04/12/92) concerning electromagnetic compatibility. Nominal voltage see label on the appliance power ratin...

  • Page 48: Sup 030 Nd

    46 r & d manager mr. Andrea castellani ec declaration of conformity ec 2006/95, ec 2004/118, ec 1992/31, ec 1993/68 saeco international group s.P.A - via torretta, 240 - 40041 gaggio montano (bo) - italy declare under our responsability that the product: automatic coffee maker sup 030 nd to which th...

  • Page 49

    T y p e s u p 0 30 n d c o d. 1 5 0 0 1 3 43 r e v .0 0 d e l 1 5 - 0 9 - 0 7 saeco international group s.P.A. Via torretta, 240 i-40041 gaggio montano, bologna tel: + 39 0534 771111 fax: + 39 0534 31025 www.Saeco.Com the manufacturer reserves the right to change the features of the product without ...