Saeco SUP 021 YDR Operating Instructions
6
8
9
1
2
1.
2.
7
- Clean nozzle with a needle
(Attention: only proceed when machine is
switched off and tap is closed)
1.1
1.2
1.
2
1
TSM SUCCESS MANUAL® - safe to use - easy to
understand due to TSM® - Total Security Management
and ergonomic communication®
T Y P E S U P 0 2 1 YDR
Observe the display:
ENERGY SAVING
DESCALING
FILL WATERTANK
VENTILATE
COFFEE BEANS EMPTY
DREGDRAWER FULL
BREWUNIT MISSING
DREGDRAWER MISSING
CLOSE DOOR
GRINDER BLOCKED
BREWUNIT BLOCKED
Push the «MENU/OK» button
Descaling see respective section ; page 6
Fill the tank with fresh water
Ventilate (prime) the circuit (Starting)
Fill coffee bean container with coffee beans
Empty the dregs drawer (with the machine switched on)
Correctly insert the brewing unit
Correctly insert the dregs drawer and the drip tray
Close the service door
Grinding motor is blocked
The motor of the brewing unit is blocked
Please call an authorized service center
close ...
open ...
DESCALE
Supplied accessories
Key for brewing unit
dismantling/assembly
Cleaning brush
Coffee measure
Test strip for water hardness
Technical data
- Type
SUP 021YDR
- Nominal voltage
See name plate under the coffee machine
- Nominal output
See name plate under the coffee machine
- Supply
See name plate under the coffee machine
- Casing material
Metal - plastic
- Dimensions (L x W x H)
approx. 27,5 x 35 x 42 cm / 11 x 14 x 17”
- Weight (net)
approx. 11 kg / 22 lbs
- Length supply cable
1.2 m / 1.30 yards
- Supply casing
yes
- Operating panel
frontal
- Water tank
removable
- Water tank capacity
1.8 l / 60 oz
- Coffee bean container capacity
180 g / 60 oz beans
- Heating
Aluminium
- Pump pressure
15 bar
- Safety devices
Security valve pump pressure
Security thermostat
TROUBLESHOOTING
No display
No power to the machine
- Switch on main power switch
- Check plug and connection
With selection «Preground coffee»
only water comes instead of coffee
- Fill with a measuring dipper of ground coffee
Coffee is not hot enough
- Activate the cup heater and put
on the cups
- Eventually clean the brewing unit,
descale
No hot water / steam
Hot water / steam nozzle is blocked
Heating time is too long
Not enough water
- Descale machine
Brewing unit cannot be
removed
1. Close service door
2. Switch on machine
3. Brewing unit is unlocked
4. Continue with
Brewing unit cannot be
inserted
«Reset» brewing unit
The output does not start
use only a non-abrasive cleaning agent
CLEANING
- During cleaning the device must not be connected to the mains.
- Do not dry any components in traditional or microwave ovens.
Wipe with a soft damp cloth
Casing
Dregs drawer
Drip tray
Rinse under fresh water
Water tank
- Rinse under fresh water
- Extract the filter on the inside of the tank
and clean carefully; insert the filter by
light pressure and rotative movement
This TSM SUCCESS MANUAL® has been examined by SEV for conformity with the safety-relevant standards, and has been
analysed by an application-oriented risk analysis for the completeness and correctness of the indications for a safe use of
the appliance. Thereby we assume a use with which can be reckoned based on common-sense.
Clean weekly
Never clean in the dishwasher
Brewing unit
1. Remove drip grid
1.1 Open service door
1.2 Remove dregs drawer and
drip tray
2. Press PUSH position and remove unit.
If necessary remove the upper filter
of the brewing unit
Clean all the components under
running warm water and dry carefully.
Clean service area
3. Reassemble brewing unit and
push in.
DO NOT press PUSH position with
the brewing unit inserted.
4. Insert drip tray and dregs drawer
and close the service door
2.1 Loosen sieve with key …
2.2 … and remove
2. Rinse under fresh water
1. Extract external body by rotation and
downwards movement
Coffee outlet
Clean weekly
Please read these TSM® operating instructions before operating the device. In order to
obtain drinks of good quality and to avoid damage or injury, follow the instructions
precisely. Ensure that these instructions are given to any other users of the device and
that they are kept in a safe place so that they can be referred to at any time. The device
has been conscientiously checked for safety and correct operation. It left the factory in
fault-free working order.
The enclosed «Safety Instructions» form an integral part of this user manual.
Read «Safety Instructions» prior to initial operation of the device and keep it together
with the user manual.
Operating Instructions
Fill the water tank with
the descaling solution as
instructed by the
manufacturer.
Push
for 3 sec.
DESCALING
READY FOR USE
DESCALING
OPEN KNOB
MACHINE IS RINSING
RINSING FINISHED
CLOSE KNOB
Observe the display... ...and continue like follows:
MACHINE IS DESCALING
Open the knob
DESCALING FINISHED
CLOSE KNOB
RINSE MACHINE
FILL WATERTANK
Close the knob
Rinse the water tank and fill with 1 liter of fresh water
RINSE MACHINE
PRESS KEY
Push
RINSE MACHINE
OPEN KNOB
Open the knob
Close the knob and the descaling process is finished.
MACHINE IS DESCALING
OPEN KNOB
1.Close the knob
DESCAL. INTERRUPTED
EMPTY WATERTANK
2.Push
3.Rinse and fill up
the water tank
Interrupt the descaling
2. Remove the internal mechanism
3. Rinse all components of the nozzle
under fresh water in order to remove
milk residues
1. Extract external body by
rotation and downwards
movement
Pannarello
4.Rinse machine
Every 3-4 months or when
the message appears:
- It is not permitted to draw off coffee, while descaler is in the water tank.
- For descaling, the machine has to be connected to the mains and the main switch
has to be switched on.
- For the descaling use a non-toxic and/or harmless descaler, available in common trading.
- NEVER use vinegar,
it could damage the machine!
- Follow closely the manufacturer's instructions!
- Should the descaling be interrupted by switching off the mains, it is absolutely necessary
to execute a complete cleaning cycle after restarting.
- During the complete descaling process the machine interrupts, automatically and at
regular intervals, the output of the descaling agent.
Preparation
Place a big container
under the hot water /
steam nozzle.
Descaling
Duration: approx. 60 min.
... the knob
If the descaling process is being
interrupted, we suggest, to start
a complete descaling cycle at
a later date.
DESCALING
READY FOR USE
cod. 1.6.589.19.02 Rev
. 00 del 20/09/02