1. DL manuals
  2. SAF
  3. Air Conditioner
  4. CFIP PhoeniX C
  5. Technical Description

SAF CFIP PhoeniX C Technical Description

Manual is about: TDM/IP Split Mount System

Summary of CFIP PhoeniX C

  • Page 1

    1 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 cfip phoenix c series tdm/ip split mount system technical description & configuration guide saf tehnika jsc 2013.

  • Page 2: Table Of Contents

    2 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 table of contents chapter 1 – basic information .................................................................................................... 5 i ntroduction ......

  • Page 3

    3 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 chapter 3 – installation ............................................................................................................. 45 i ntroduction ...................

  • Page 4

    4 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 ip configurations ................................................................................................................................ 88 basic ip addresses...

  • Page 5

    5 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 chapter 1 – basic information introduction cfip phoenix c is a universal idu designed for split-architecture high-performance point-to-point (ptp) digital microwave lin...

  • Page 6

    6 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 chapter 2 – technical description introduction digital microwave system cfip phoenix c is designed in split mount version, the idu - odu architecture. There is only one...

  • Page 7

    7 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 diagram of received data) – atpc function support (automatic transmit power control) – integrated spectral analyser for the detection of the free channel, or alternativ...

  • Page 8

    8 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 – sfp 2 gige/emm – user port for alternative gigabit ethernet connection or emm module connection – flash usb a – usb interface for connecting usb memory – mng usb b – ...

  • Page 9

    9 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 block diagram of the cfip phoenix c indoor unit the function of the indoor unit is evident from the block diagram in figure 4. Figure 4: block diagram of the indoor uni...

  • Page 10

    10 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 block diagram of design single the main application in design single is a transmission of a single data stream over air. Cfip phoenix c idu is configured into this mod...

  • Page 11

    11 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 block diagram of design multi the main application in design multi is a transmission of more (up to four) independent data streams over air. Cfip phoenix c is configur...

  • Page 12

    12 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 block diagram of design protected the main application of design protected is a 1+1 system configuration when the protection (hitless in specific conditions) is requir...

  • Page 13

    13 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 8: detailed block diagram of design protected (slave mode) the user data ports lan 1/2, sfp 2 are deactivated (don't transmit data from idu). Port sfp 1 is rese...

  • Page 14

    14 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 block diagram of design aggregate the main application in design aggregate is a true 2+0 system configuration (capacity doubling) when the eth traffic aggregation is r...

  • Page 15

    15 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 10: detailed block diagram for design aggregate- slave the ethernet switch is configured into mode where both wan ports wan a/b are connected to packet processo...

  • Page 16

    16 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 idu block scheme in terms of ip the following figure 11 depicts a simplified block diagram of the cfip phoenix c idu in terms of ip management. Figure 11: detailed blo...

  • Page 17

    17 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 each device supports also the following advanced ip settings – the secondary ip address, including the mask – the address is assigned to the port eth 0, the mask indic...

  • Page 18

    18 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 12: block diagram of the outdoor unit outdoor unit is an integral part of the antenna system. Odu is mounted behind the parabolic antenna. In dependence on requ...

  • Page 19

    19 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 13: preview of outdoor unit for licensed bands attaching the odu to the antenna is done with an integrated waveguide transition (microwave adapter) and it is me...

  • Page 20

    20 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 odu technical specifications cfip odu rsl at 10 -6 (dbm) and total payload capacity (mbps) bw***, mhz modulation fec**** 6 ghz 7 ghz 8 ghz 10 ghz 11 ghz 13 ghz 15 ghz ...

  • Page 21

    21 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 cfip odu rsl at 10 -6 (dbm) and total payload capacity (mbps) bw***, mhz modulation fec**** 6 ghz 7 ghz 8 ghz 10 ghz 11 ghz 13 ghz 15 ghz 18 ghz 23 ghz 26 ghz 38* ghz ...

  • Page 22

    22 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 cfip odu waveguide flange sizes 6 ghz 7, 8 ghz 10, 11 ghz 13, 15 ghz 18, 23 ghz 26 ghz 38 ghz n-type ubr84 ubr100 ubr140 ubr220 ubr260 ubr320 max. Power consumption sp...

  • Page 23

    23 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 external multiplexer modules the basic function of external multiplexer modules is multiplexing of specific data types (e1, t1, asi) into one high speed data stream wh...

  • Page 24

    24 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 all the ports are protectcted against esd (electrostatic discharge), cde (cable discharge events), and lightning. In case of connecting 16e1 balanced rj-45 interface t...

  • Page 25

    25 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 led indicators on the cfip-16e1/t1-ext – port status – sfp 1/2 link – indication of presented signal at sfp port - flashes – signal detected and synchronized, valid co...

  • Page 26

    26 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 up to 64 e1/t1 external multiplexer application up to 4 x cfip-16e1/t1-ext modules can be connected into cascade and thus get the maximum quantity of 64 e1 / t1 channe...

  • Page 27

    27 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 1+1 application with cfip-16e1/t1-ext the combination of 1+1 protected scheme with extension module cfip-16e1/t1-ext. Add-drop multiplexer application.

  • Page 28

    28 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 management and configuration examples of cfip-16e1/t1-ext the configuration and status of the module can be found in web gui in ports/emm management menu: emm support ...

  • Page 29

    29 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 emm card #x settings for cfip-16e1/t1-exp - port/channel number - a number of e1/t1 ports (channels), the number in red indicates alarm status of appropriate internal ...

  • Page 30

    30 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 item parameter value idu direction interface 1x sfp 1000base-sx (proprietary gige protocol) for connection with cfip phoenix c idu ext module extension interface 1x sf...

  • Page 31

    31 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 item parameter value en 61000-3-2,3 safety iec 60950-1/en 60950-1 extension module cfip-asi-ext extension card cfip-asi-ext (external multiplexer module) provides asi ...

  • Page 32

    32 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 led indicators on the cfip-asi-ext – system status – status – indication of the local emm status - lights – status ok (card enabled, proper communication with idu) - f...

  • Page 33

    33 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 this application uses combination of cfip phoenix c idu with selected multi design and one cfip- asi-ext card in unidirectional mode (tx ports at one link side, rx por...

  • Page 34

    34 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 management and configuration examples of cfip-asi-ext the configuration and status of the module can be found in web gui in ports/emm management menu: emm support this...

  • Page 35

    35 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 emm card #x settings for cfip-asi-exp - port/channel number - a number of asi ports (channels) - enable – selects which asi ports are enabled for dvb asi connection. T...

  • Page 36

    36 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 - speed limit(rx) [mbps] - maximal data rate for inbound traffic to avoid overload of overall link capacity. This settings is available in rx mode only cfip-asi-ext te...

  • Page 37

    37 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 item parameter value protection en 60529 (ip31) input voltage level cfip-ext only -20 vdc up to -60 vdc (standard version) power consumption cfip-asi-ext environmental...

  • Page 38

    38 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 the module contains additional 5 connectors in comparison to basic asi module: master module ports – tsi1 in: – 1pps - input source of 1pps pulse (required) – 10mhz - ...

  • Page 39

    39 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 basic block diagram of the cfip-asi&tsi_ext the blue lines represent the separate time transfer (1pps/10mhz) path, the green lines represent path of asi signals and re...

  • Page 40

    40 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 connection scheme of the link with cfip-asi&tsi-ext modules: notes: the timing synchronization is supported in multi and aggregate designs only. The condition for corr...

  • Page 41

    41 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 timing configuration and status example for slave device mode selection and clock status – timing modes - mode of synchronization signal – clock recovery source - sour...

  • Page 42

    42 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 – noppsref (holdover) – this message will be displayed when there is no source signal detected. The timing module is automatically switched to "holdover" mode generati...

  • Page 43

    43 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 alternatively directional coupler for 1+1 hsb protection configuration or omt (orthomode transducer) adapter for cross polarization configuration (aggregate 2+0) can b...

  • Page 44

    44 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 ethernet cable with rj-45 connectors twisted pair type cat5e from belden manufacturer is a suitable ethernet cable. Surge suppressors when the coaxial cable is enterin...

  • Page 45

    45 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 chapter 3 – installation introduction the installation of cfip phoenix c microwave system and its start up can perform only manufacturer´s authorized partner. Manufact...

  • Page 46

    46 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 table 4: odu polarizations odu position adapter slot vertical polarization horizontal polarization mounting odu to antenna mounting the odu to the parabolic antenna is...

  • Page 47

    47 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 24: final odu and antenna installation attention: always fasten 2 latches which are against each other at the same time. Make sure that the adapter slot and odu...

  • Page 48

    48 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 26: 2x idu in 1u 19" cabinet attention: do not forget to ground the cfip phoenix c indoor unit with the grounding screw located on the front panel of the idu to...

  • Page 49

    49 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 attention: pay close attention to the correct power supply pinout polarity. Power supply pole 0 vdc is ever internally grounded inside idu! Grounding for reliable and ...

  • Page 50

    50 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 pc setup with lan adapter in the case you are using management ethernet cable for initial configuration you must first set your computer ip address from the range whic...

  • Page 51

    51 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 30: pc ip lan setup – internet protocol pc setup with usb adapter in the case you are using management usb cable for initial configuration you must first instal...

  • Page 52

    52 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 default idu usb ip settings ip address 10.10.11.10, net-mask 255.255.255.0 therefore it is necessary to set the pc address in the range of 10.10.11.1 – 254, except for...

  • Page 53

    53 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 when incorrect login name or password are entered the warning message „incorrect login name or password” will appear in the idu login window. Gui basics after a succes...

  • Page 54

    54 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 ip setting figure 34: ip address configuration – gui page “ip / address it is recommended to enter basic ip configuration of local and remote units (idus) at the very ...

  • Page 55

    55 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 for applying any ip configuration into the running system it is necessary to subsequently confirm ip settings with pressing write and apply button in confirmation wind...

  • Page 56

    56 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 36: radio parameters setting – gui page “radio / parameters set all the other parameters as depicted in the figure 36 and confirm them with apply button. Then s...

  • Page 57

    57 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 38: curve of dependence rsl [dbm] on rssi voltage [v] antenna alignment might be performed only in favourable weather conditions. Adverse weather conditions are...

  • Page 58

    58 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 obtaining the basic link information connect your pc according to the procedure described above and use „general / status” page for obtaining the required information ...

  • Page 59

    59 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 when updated configuration is done and mse level stands with expected level, press button clear local and remote on page „general / status”. Then go to the page „count...

  • Page 60

    60 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 connecting gigabit ethernet port gigabit ethernet 10/100/1000 mbps port pinout is given in figure 45. The user has to make sure that all the four pairs of the cable ac...

  • Page 61

    61 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 chapter 4 – link configuration introduction after the installation of the microwave link itself it is necessary to carry out the complete set-up of all the required li...

  • Page 62

    62 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 for the standard configuration we recommend to login in the user mode. Administrator level is superior to the user level. When the administrator tries to login the sys...

  • Page 63

    63 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 setting mistakes like radio interferences, port loopbacks etc. Txpower is muted and all traffic ports are down in „protection off” mode. Note: customer should set all ...

  • Page 64

    64 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 aggregation scheme settings availability of „aggregation” settings page depends primarily on selected design type and available license key. Check advanced system conf...

  • Page 65

    65 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 - off – this item (mode) disables aggregation function. The function in this mode is similar to function of design multi but with just three channels over air. – tx ag...

  • Page 66

    66 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 49: wireless link info – gui page „general / info” there is displayed basic system identification information like idu/odu serial numbers, product numbers, firm...

  • Page 67

    67 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 50: date and time specification – gui page „general / date” the description of particular setting and display boxes – date – specification of actual date. – tim...

  • Page 68

    68 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 51: access levels setting – gui page „general / users” each of the three possible login modes has different rights for the system management. The following logi...

  • Page 69

    69 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 each access right group. Note: all settings from this page are directly saved to a specific start-up memory which is common for all alternative configurations w0-w3. A...

  • Page 70

    70 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 it is also possible to check the status of alarms on the same gui page – monitoring of actual alarm status of both active and also of inactive alarm ids. – checking co...

  • Page 71

    71 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 alarm row. - warning = actual modem fer value is higher or equal to the fer threshold defined in the same alarm row. – mse level alarm – id 01.0.12 this alarm id indic...

  • Page 72

    72 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 – odu comm alarm – id 01.0.25 (critical) this alarm id indicates incorrect or missing communication between the local idu and the local odu. - no alarm = idu-odu commu...

  • Page 73

    73 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 53: radio parameters setting – gui page „radio / parameters” the description of particular setting and display boxes – tx frequency – transmission frequency can...

  • Page 74

    74 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 note: the atpc function should be always off during the installation! – atpc rx level – required level for automatic transmit power control. Field specifies the optima...

  • Page 75

    75 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 example: 128_28000_01 – 256 – code for 256 qam, other possibilities are 4/8/16/32/64/128/256 – 56000 – code for 56 mhz bw, other possibilities are 07000, 10000, 14000,...

  • Page 76

    76 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 port configurations in respect of management access type, traffic modification (number of independent channels over air) and the protection / aggregation function pref...

  • Page 77

    77 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 priority allocation goes from the left to the right. – available speed – it indicates the available speed for appropriate channel. This value depends on selected actua...

  • Page 78

    78 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 57: ports setting in multi design the speed allocation set-up is different in comparison with the design single. The overall allocated traffic capacity (the sum...

  • Page 79

    79 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 58: ports setting in protected master mode figure 59: ports setting in protected slave mode basic port settings – design aggregate port settings for design aggr...

  • Page 80

    80 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 60: ports setting in aggregate master mode the channel eth-4 at slave unit is reserved for the slave aggregation stream (correct speed must be set), rest of eth...

  • Page 81

    81 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 eth vlan settings vlan configuration is basically used for the separation of management traffic from other customer data traffics. It can be useful to configure eth vl...

  • Page 82

    82 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 from the same group can communicate with one another. The other ports are completely isolated. It is possible that isolated networks (different groups) can use the sam...

  • Page 83

    83 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 63: eth synce gui page the description of particular setting and display boxes – synce reference – this parameter defines the port which is selected for clock s...

  • Page 84

    84 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 64: advanced eth settings the description of particular setting and display boxes – optional eth – jumbo frames support – these boxes make it possible to select...

  • Page 85

    85 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 priority abbreviations – fpri initial frame priority 0 up to 7 (bits [2:0]) – qpri queue priority 0 up to 3 (bits [1:0]) – iqpri initial queue priority 0 up to 3 (bits...

  • Page 86

    86 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 priority queues are empty. Note: qos mode configures egress policy (output from switch) for each port, whereas other qos setting modes configure ingress port policies ...

  • Page 87

    87 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 vlan tag. Such updated frame can input into the switch with qos priority which is different from priority of the same frame at the output from switch. – priority overr...

  • Page 88

    88 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 ip configurations in respect of management access type it is possible to use either the local connection via lan 3 port which is connected to the ethernet switch and i...

  • Page 89

    89 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 66: basic ip setting all ip settings are applied in two steps. Temporary configuration ip file is changed with pressing apply button, but setting changes are no...

  • Page 90

    90 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 67: static route and nat setting each static route and/or nat record must be entered separately. The same confirmation window as for ip address configuration ap...

  • Page 91

    91 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 the add button is used for entering a new nat record into the nat table, alternatively the delete button for deleting record from the nat table. Optionally the delall ...

  • Page 92

    92 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 68: snmp setting advanced ip settings the advanced ip section makes it possible to change extended ip configuration which usually remains in default state. This...

  • Page 93

    93 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 the most useful setting is ntp mode. When “none” is selected, no time synchronization is required. – server ip – it specifies a remote time server ip when ntp or rdate...

  • Page 94

    94 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 70: write confirmation when the configuration is properly saved, it is possible to write actual configuration also into optional memories (w1-w3). This operatio...

  • Page 95

    95 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 – the configuration is now saved in your pc and alternatively in usb memory stick. Figure 72: configuration, logs and license request backup a detailed description of ...

  • Page 96

    96 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 on page 79) firmware and license upgrade firmware and license upgrade is available in admin mode only. We recommend to verify the loaded version of firmware in the idu...

  • Page 97

    97 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 print-out for information, what parts should be upgraded. – next choose one of the following steps. - select the file fw_all.Afw from the provided sw package. The whol...

  • Page 98

    98 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 are: - single – one independent traffic channel over air - multi – up to four independent traffic channels over air - protected 1+1 – link protection by means of two i...

  • Page 99

    99 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 chapter 5 – configuration examples example 1 – in-band management separated by vlan in-band management configuration with management traffic separation by means of vla...

  • Page 101

    101 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 76: example 1 – selection of design single at location 1 then the proper ip address setting must entered and applied. The new login into system is automaticall...

  • Page 102

    102 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 79: example 1 – ports speed setting at location 1 the configuration of the idu 2 at location 2 is similar to above explained gui pages but with appropriate par...

  • Page 103

    103 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 main advantages – separate management channel for local and remote idu access. The whole system capacity is available for data traffic. Disadvantages – management tra...

  • Page 104

    104 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 at intermediate ip window). Figure 81: example 2 – ip address setting at location 1 then most important step of such out-of-band management configuration is the prope...

  • Page 105

    105 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 83: example 2 – vlan and port groups setting at location 1 then configure the basic port parameters like ethernet channel speed and lan port modes. Figure 84: ...

  • Page 106

    106 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 this concrete example describes application where multi design is selected on both link sides, modulation is qam128 in bw 30 mhz and appropriate maximal data speed is...

  • Page 107

    107 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 design multi must by selected as the first step in configuration process on both idus. Figure 86: example 3 – selection of design multi at location 1 then the proper ...

  • Page 108

    108 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 vlan configuration will be returned after 120 seconds). Figure 88: example 3 – port modes and port groups setting at location 1 the ethernet channel eth 2 is used as ...

  • Page 109

    109 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 the application example is shown at the figure 90. The configuration of the most important gui pages at location 1 (provider side) and location 2 (customer side) is s...

  • Page 111

    111 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 92: example 4 – vlan and port groups setting at location 1 figure 93: example 4 – ports speed setting at location 1.

  • Page 112

    112 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 94: example 4 – vlan and port groups setting at location 2 figure 95: example 4 – ports speed setting at location 2.

  • Page 113

    113 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 example 5 – advanced qos configuration the prioritising of different data traffic streams by means of qos is a main application for idu advanced qos functionality. Th...

  • Page 115

    115 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 then the next qos modes and parameters are defined in eth advanced section. The vtu priority override option is used for qos discrimination at this side. Figure 98: e...

  • Page 116

    116 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 100: example 5 – advanced qos setting at location 2 example 6 – sync eth configuration the synchronous clock transfer over packet based system is the main appl...

  • Page 118

    118 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 102: example 6 – ports speed setting at location 1 then the synce parameters are defined in eth synce section. Port lan 1 is selected as reference source, rf s...

  • Page 119

    119 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 104: example 6 – ports speed setting at location 2 figure 105: example 6 – synceth setting at location 2 the configuration of idu 3 is similar to above explain...

  • Page 120

    120 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 transmitter failure detection no switch over between active and muted transmitter is ordered. The application example for 1+1 / hsb mode is shown at the figure 106.Th...

  • Page 122

    122 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 then the proper ip address setting must entered but should by applied later together with ip nat changes (chose continue button at intermediate ip window). The requir...

  • Page 123

    123 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 110: example 7 – basic radio parameters at idu1 – location 1 then port groups and basic port parameters must be properly configured according to defined connec...

  • Page 124

    124 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 112: example 7 – basic ports setting at idu1 – location 1 the similar configuration should be applied on all idus in protection scheme. The local usb port (ip ...

  • Page 125

    125 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 protection scheme is properly configured now. Ip management access uses nat functionality. – master unit at provider side is accessible directly at 192.168.3.201 – sl...

  • Page 127

    127 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 115: example 8 – default „protection off” mode at location 1 then the proper ip address setting must entered and applied by pressing apply button. Such change ...

  • Page 128

    128 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 117: example 8 – basic radio parameters at idu1 – location 1 then port groups and basic port parameters must be properly configured according to defined connec...

  • Page 129

    129 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 119: example 8 – basic ports setting at idu1 – location 1 the similar configuration should be applied on all idus in protection scheme. The local usb port (ip ...

  • Page 130

    130 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 protection scheme is properly configured now. The lan 3 port on both master idus can be used for management access. The similar slave unit port configuration (port sp...

  • Page 132

    132 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 channel eth 4 at slave unit. The proprietary aggregation algorithm divides traffic into two way on the base of free space in transmit fifos, therefore division doesn'...

  • Page 134

    134 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 124: example 10 – basic radio parameters at idu1 – location 1 then port groups must be properly configured according to defined connection block scheme. Figure...

  • Page 135

    135 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 126: example 10 – aggregation mode selection at idu1 – location 1 the last step is correct configuration of eth channels on all master and slave units. Figure ...

  • Page 136

    136 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 figure 128: example 10 – port setting at slave idu2 - location 1 the aggregation scheme is properly configured now..

  • Page 137

    137 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 chapter 6 – technical parameters general table 5: system parameters item parameter value frequency operating frequency range 6 to 42 ghz frequency plans according to ...

  • Page 138

    138 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 item parameter value interface 4x bnc (dvb-asi) coding 8b/10b, mpeg-2 ts speed for asi channel 8-216 mbps idu interface 2x sfp 1000base-sx (proprietary gige protocol)...

  • Page 139

    139 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 miscellaneous table 9: miscellaneous item parameter value idu mechanical dimension [w x h x d] 210 mm x 44 mm x 250 mm weight 2 kg protection ip31 (en 60529) odu mech...

  • Page 140

    140 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 abbreviation list agc - automatic gain control on rf cable ais - continual sequence of ones on e1 data according to norm aneg -autonegotiation - automatic speed and d...

  • Page 141

    141 cfip phoenix c series tdm/ip split mount system technical description and configuration guide • rev. 1.0 • © saf tehnika jsc 2013 saf tehnika jsc contacts saf tehnika a/s technical support can be reached by: - email: techsupport@saftehnika.Com - telephone: +371 67046840 - fax: +371 67046809.