SAF CFM-34-REBM Manual - page 28
Modular Fast Ethernet Bridge Management System Technical Description and Configuration Guide
V. 3.12. 1.0
·
© SAF Tehnika A/S 2003
28
Mod
{3|4} detect
Detect and show current settings, - displays a list of settings of the
respective interface module. The detection procedure is carried out
each time when IDU is started up. This command is for diagnostic
purposes only.
Mod
dump
Show a list of modules and contents of their respective CPU registers (in
hexadecimal system). This command is for diagnostic purposes only.
Example:
SAF>mod dump
21, 02, CD, FF, 00, 00, 00, 00, 78, 00, 00, FF, 00, 01, 77, 03,
25, 01, E0, E4, E4, FF, 08, FF, FF, FF, FF, FF, FF, FF, FF, FF,
25, 02, E7, E6, E7, FF, 81, FF, FF, FF, FF, FF, FF, FF, FF, FF,
2B, 01, 00, E0, FF, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00,
IP
addr
IPaddress
>
Set the IP address of Ethernet management port (requires
to restart the management module CPU).
Important!: Do not enter address “255.255.255.255”
IP
mask
IPnetmask
>
Set the IP netmask of Ethernet management port (requires
to restart the management module CPU).
IP
gw
IPaddress
>
Set the IP address of the default gateway to the service
channel (requires to restart the management module CPU).
IP
seraddr
IPaddress
>
Set the IP address of the serial port of service channel for
the local (near-end) IDU management module (requires to
restart the management module CPU).
IP
remaddr
IPaddress
>
Set the IP address of the serial port of service channel for
the remote (far-end) IDU management module (requires to
restart the management module CPU).
Route
add
destinationIPaddr
> Mask
[
netmask
]
gateway
> [
metric
]
Add a static route to the routing table. The variable
“metric” is set to 1 by default (requires to restart the
management module CPU). Example:
Route add 192.168.205.010 Mask 255.255.255.0
155.13.79.13 5
Route
delete
destinationIPaddr
>
[
netmask
]
Delete a static route from the routing table (requires to
restart the management module CPU).
SNMP
community read
communityname
>
Specify the SNMP community name of the agent to enable
parameters to be read (not configured). The default
community name to read parameters is s
af-public
SNMP
community write
communityname
>
Specify the community name of the agent to enable
parameters to be read and/or written (configured). The
default community name for read/write is
saf-private
SNMP
trap
IPaddress
>
Set the IP address of the management terminal with the
installed Trap Manager software, based on SNMP platform
(requires to restart the management module CPU).
Configuring E1 Interface Module parameters
Command
Description
Mod
{3|4} setE1 {Aloop | Dloop |
Off}
Set the analog, digital or remote loopback in the module
(
Aloop
– analog loopback;
Dloop
– digital loopback,
off
–
disable current E1 module loopback).
Example:
Mod 3 setE1 Dloop
Mod
{3|4} setE1 {120 | 75}
Set the impedance of E1 interface, 120 Ω or 75 Ω.
Mod
{3|4} setE1 TxAIS {on | off}
Enable/Disable the transmission of AIS signal (for
configuration and testing purposes only).