Sage Products Comfort Personal Cleansing 7931 Operating Instructions - page 2
This microwave is to be used SOLELY for Sage Comfort Personal Cleansing
®
products. The microwave has been
electronically programmed and safety tested to be used exclusively with Comfort Personal Cleansing products. ANY
other use of the microwave by the facility, including but not limited to, use with other bathing products can result in
overheating, fire or other hazardous conditions and is expressly forbidden. Refer to individual packages of Comfort
Personal Cleansing products for recommended heating times.
WARNING:
To reduce the risk of fire, burns, electrical shock, injury or exposure to excessive microwave energy:
1. Read all instructions before using this microwave.
2. Read and follow the specific “PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE
MICROWAVE ENERGY” in this manual.
3.
This microwave is supplied with a hospital-grade green dot cord and plug. Connect only to UL-listed outlet.
See the “GROUNDING INSTRUCTIONS” in this manual for specific information.
4. Install this microwave only in accordance with the installation instructions found in this manual.
5. DO NOT cover or block any openings on this appliance.
6. DO NOT tamper with or make any adjustments to the door, control panel, housings, safety switches or
any other part of the Comfort Personal Cleansing Microwave.
7. DO NOT remove any panel or cover.
8. DO NOT store or use this appliance outdoors. DO NOT use this product near water—for example, near a kitchen
sink, in a wet basement, or near a swimming pool.
9. DO NOT use this microwave for any material other than Comfort Personal Cleansing products in accordance
with instructions on the label.
10. DO NOT let the cord hang over edge of table or counter.
11. This microwave is to be used by adults familiar with its operation and these safety instructions.
12. DO NOT operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been
damaged or dropped.
13. DO NOT immerse cord or plug in water.
14. Keep cord away from heated surfaces.
15. The microwave is to be serviced only by qualified service personnel. There are no external or user-serviceable
fuses. Contact Sage Products for repair or adjustment.
16. Use this appliance only for its intended purpose as described in this manual. DO NOT use corrosive chemicals
or vapors in this appliance. This type of microwave is specifically programmed to heat Comfort Personal
Cleansing products. It is NOT designed for industrial or laboratory use. The use of corrosive chemicals in heating
or cleaning will damage the appliance and may result in radiation leaks.
17. When cleaning surfaces of door and microwave that come together on closing the door, use only mild,
non-abrasive soaps or detergents applied with a sponge or soft cloth.
Important:
Sage Products or its suppliers, Panasonic Canada Inc. and the PIC (Panasonic Industrial Company) are not responsible
for any damage caused by improperly installing this microwave. Read and follow these instructions carefully.
Tools and Parts
The following tools and parts are needed to install the oven:
•
One 5/16-inch bolt purchased by user (See “How to Select the Bolt Length”)
•
Drill and-3/8 inch drill bit
•
Nail or center punch
•
Hammer
•
Scissors
Figure 1
Figure 2
Figure 3 & 4
Figure 5
How to Select the Bolt Length
1. Remove the Bolt Gauge from this manual and place it straight up near the front edge of
the shelf upon which the oven will rest.
2. Measure the distance from the bottom of the shelf to lines A and B on the Bolt Gauge.
a) From the bottom of the shelf to line A is the minimum length of the bolt.
b) From the bottom of the shelf to line B is the maximum length of the bolt.
If the bolt is shorter than A or longer than B, you cannot use it to secure the oven.
3. Purchase one 5/16-inch-18 bolt whose length falls between the minimum and maximum
bolt length as determined in step 2 above. (Figure 1 & 2)
CAUTION: Washers should be used to correct for long bolt length, and when (wooden)
shelf compresses to allow maximum bolt length to be exceeded. Internal parts of oven may be
damaged due to oversize bolt length.
How to Install the Microwave
1. Be certain that:
a) All 4 legs are supported by the shelf (microwave may hang over an open shelf
or shelf front). (Figure 3 & 4)
b) The power cord on the microwave can reach the electrical outlet.
c) The electrical outlet is not blocked by the microwave. Power cord must be
able to be unplugged without moving the microwave.
2. Use a center punch or nail to make an indentation in the shelf at the spot designated as
the center for the drill holes shown in Figure 5.
3. Drill one 3/8-inch hole in shelf at spot indicated in Figure 5, keeping the drill
perpendicular to the shelf.
4. Clean the drill holes.
5. Place the microwave on the shelf. Align hole
in the base of the microwave with the drilled
hole and bolt the microwave to the shelf from
the underside of the shelf.
IMPORTANT SAFETY INSTRUCTIONS
SECURITY BOLT INSTALLATION INSTRUCTIONS