1. DL manuals
  2. Sailor
  3. Satellite TV System
  4. 100
  5. Installation Manual

Sailor 100 Installation Manual

Summary of 100

  • Page 1

    Installation manual sailor 100 satellite tv.

  • Page 3

    Sailor 100 satellite tv installation manual document number: 98-136280-b release date: 18 january 2013 sailor100im.Book page i friday, january 18, 2013 10:28 am.

  • Page 4

    Ii 98-136280-b disclaimer any responsibility or liability for loss or damage in connection with the use of this product and the accompanying documentation is disclaimed by thrane & thrane. The information in this manual is provided for information purposes only, is subject to change without notice a...

  • Page 5: Safety Summary

    98-136280-b iii safety summary the following general safety precautions must be observed during all phases of operation, service and repair of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture ...

  • Page 6

    Iv 98-136280-b keep away from live circuits operating personnel must not remove equipment covers. Component replacement and internal adjustment must be made by qualified maintenance personnel. Do not replace components with the power cable connected. Under certain conditions, dangerous voltages may ...

  • Page 7: Record Of Revisions

    98-136280-b v record of revisions rev. Description release date initials a original document 21 september 2012 ufo b the following sections have been added: the following sections have been edited: 1.3, 2.1, 2.1.1, 3.3.2, 3.5, 4.2, 6.3.3, 6.3.6, 6.3.10, 6.4, 6.5.1 the following figures have been add...

  • Page 8

    Vi 98-136280-b sailor100im.Book page vi friday, january 18, 2013 10:28 am.

  • Page 9: Table Of Contents

    98-136280-b vii table of contents chapter 1 about this manual 1.1 intended readers ................................................................................ 1-1 1.2 manual overview ............................................................................... 1-1 1.3 software version ..........

  • Page 10

    Table of contents viii 98-136280-b chapter 3 installation 3.1 unpacking .........................................................................................3-1 3.1.1 what’s in the box .............................................................................3-1 3.1.2 control panel .............

  • Page 11

    Table of contents 98-136280-b ix chapter 4 interfaces 4.1 interfaces of the sailor 100 satellite tv acu ................................... 4-1 4.1.1 leds, display and keypad ................................................................ 4-1 4.1.2 connector panel — overview ..........................

  • Page 12

    Table of contents x 98-136280-b 6.3 configuration with the web interface ...............................................6-8 6.3.1 overview and navigation .................................................................6-8 6.3.2 using the dashboard ......................................................

  • Page 13

    Table of contents 98-136280-b xi chapter 8 service 8.1 getting support: helpdesk .................................................................8-2 8.1.1 help desk and diagnostic report ......................................................8-2 8.2 software update .....................................

  • Page 14

    Table of contents xii 98-136280-b b.3 alternative grounding for steel hulls ................................................B-4 b.3.1 grounding the acu .........................................................................B-4 b.3.2 grounding the adu ..................................................

  • Page 15: List Of Figures

    98-136280-b xiii list of figures chapter 1 about this manual chapter 2 introduction figure 2-1: adu, acu, control panel and multiswitch (optional) ............................................2-2 figure 2-2: above deck unit (adu) ..........................................................................

  • Page 16

    List of figures xiv 98-136280-b figure 3-22: acu, lan connector at the front: service port..................................................... 3-23 figure 3-23: acu, ground stud............................................................................................... 3-24 figure 3-24: connecti...

  • Page 17

    List of figures 98-136280-b xv figure 6-23: statistics report (example) .................................................................................. 6-31 figure 6-24: web interface: administration ............................................................................6-32 figure 6-25: web...

  • Page 18

    List of figures xvi 98-136280-b figure b-6: separate ground cable ........................................................................................ B-9 figure b-7: isolation of the adu from the mounting base..................................................... B-10 figure b-8: adu isolation a...

  • Page 19: List Of Tables

    98-136280-b xvii list of tables chapter 1 about this manual table 1-1: list of related documents .................................................................................... 1-2 chapter 2 introduction table 2-1: model and part numbers for the sailor 100 satellite tv system (t&t units) .........

  • Page 20

    List of tables xviii 98-136280-b table 6-10: control panel, create or edit satellite profiles ..................................................... 6-39 table 6-11: top-level menus of the acu ............................................................................... 6-46 table 6-12: antenna men...

  • Page 21: About This Manual

    98-136280-b 1-1 chapter 1 1111 a bout t h is m anu al about this manual 1 1.1 intended readers this is an installation manual for the sailor 100 satellite tv system, intended for installers of the system and service personnel. Personnel installing or servicing the system must be properly trained and...

  • Page 22: 1.5

    Typography 1-2 chapter 1: about this manual 98-136280-b 1.5 typography in this manual, typography is used as indicated below: bold is used for the following purposes: • to emphasize words. Example: “do not touch the antenna”. • to indicate what the user should select in the user interface. Example: ...

  • Page 23: 1.6

    Precautions 98-136280-b chapter 1: about this manual 1-3 1111 a bout t h is m anu al 1.6 precautions warnings, cautions and notes text marked with “warning”, “caution”, “note” or “important” show the following type of data: • warning : a warning is an operation or maintenance procedure that, if not ...

  • Page 24

    Precautions 1-4 chapter 1: about this manual 98-136280-b sailor100im.Book page 4 friday, january 18, 2013 10:28 am.

  • Page 25: Introduction

    98-136280-b 2-1 chapter 2 2222 in tr oducti o n introduction 2 this chapter is organised in the following sections: • sailor 100 satellite tv system • part numbers and options 2.1 sailor 100 satellite tv system the sailor 100 satellite tv provides television for ships across the world. The sailor 10...

  • Page 26

    Sailor 100 satellite tv system 2-2 chapter 2: introduction 98-136280-b the following figures show the sailor 100 satellite tv system . Sailor 100 satellite tv features simple installation with one 50 ohm coax cable between adu and acu. Full remote control and troubleshooting with built-in test equip...

  • Page 27: 2.1.1

    Sailor 100 satellite tv system 98-136280-b chapter 2: introduction 2-3 2222 in tr oducti o n 2.1.1 above deck unit (adu) the sailor 100 satellite tv adu is a 103 cm stabilised tracking antenna, consisting of a suspended antenna with a standard global rf configuration. The adu’s weight is 126 kg. It ...

  • Page 28

    Sailor 100 satellite tv system 2-4 chapter 2: introduction 98-136280-b modules in the sailor 100 satellite tv adu 1. Gps module. 2. Television interface module (tim). 3. Dc-motor driver module for cross elevation (ddm). 4. Cross elevation motor and encoder. 5. Zero reference module (3 pcs, 2 in figu...

  • Page 29

    Sailor 100 satellite tv system 98-136280-b chapter 2: introduction 2-5 2222 in tr oducti o n 8. Low noise block downconverter (lnb). 9. Polarisation motor. 10. Polarisation motor module (pmm) (not visible on photo). 11. Inertial sensor module (ism). 12. Elevation locking pin to lock the antenna dish...

  • Page 30

    Sailor 100 satellite tv system 2-6 chapter 2: introduction 98-136280-b sailor 100 satellite tv adu interface all communication between the adu and the acu passes through a single standard 50 ohm cable (with n connector) through the rotary joint. No cable work is required inside the radome. Programma...

  • Page 31: 2.1.2

    Sailor 100 satellite tv system 98-136280-b chapter 2: introduction 2-7 2222 in tr oducti o n service friendly the system configuration is saved in two modules, there is no loss of data at repair. The large service hatch of the radome gives easy access to the adu on site. The service switch in the ad...

  • Page 32: Set To On

    Sailor 100 satellite tv system 2-8 chapter 2: introduction 98-136280-b acu interfaces the acu has the following interfaces and switch: • 4 x f-connector for tv outputs (75 ohm). • ground stud • n-connector for adu cable (50 ohm). • connector for dc out (for internal use). • sma connector for rf rx o...

  • Page 33: 2.1.3

    Sailor 100 satellite tv system 98-136280-b chapter 2: introduction 2-9 2222 in tr oducti o n software update is done via a connected pc and the built-in web interface of the acu. 2.1.3 control panel for setup and operation with the control panel you can supervise, configure and operate the acu and t...

  • Page 34: 2.1.6

    Sailor 100 satellite tv system 2-10 chapter 2: introduction 98-136280-b number of sailor transmodulator modules customised to your needs. For further information see the installation manual of the sailor transmodulator. 2.1.6 power supply (optional) use the sailor 6080 ac/dc power supply to provide ...

  • Page 35: 2.2

    Part numbers and options 98-136280-b chapter 2: introduction 2-11 2222 in tr oducti o n 2.2 part numbers and options 2.2.1 applicable thrane & thrane model and part numbers the following model and part numbers are available for the sailor 100 satellite tv system: 2.2.2 options for sailor 100 satelli...

  • Page 36

    Part numbers and options 2-12 chapter 2: introduction 98-136280-b sailor100im.Book page 12 friday, january 18, 2013 10:28 am.

  • Page 37: Installation

    98-136280-b 3-1 chapter 3 3333 in stall ati o n installation 3 this chapter is organised in the following sections: • unpacking • site preparation • installation of the adu • installation of the acu • installation of the control panel 3.1 unpacking 3.1.1 what’s in the box adu unpack your sailor 100 ...

  • Page 38: 3.1.2

    Unpacking 3-2 chapter 3: installation 98-136280-b 3.1.2 control panel unpack your control panel and check that the following items are present: • dc power cable • wheel knob • u-bracket mount • flush mount gasket • screw kit • cable relief plate • installation manual 3.1.3 initial inspection inspect...

  • Page 39: 3.2

    Site preparation 98-136280-b chapter 3: installation 3-3 3333 in stall ati o n 3.2 site preparation the following topics have to be considered when installing the adu: • general site considerations • obstructions (adu shadowing) • blocking zones — azimuth and elevation • ship motion and offset from ...

  • Page 40: 3.2.2

    Site preparation 3-4 chapter 3: installation 98-136280-b 3.2.2 obstructions (adu shadowing) place the adu so that it has as much free line-of-sight without any structures in the beam through one full 360 degrees turn of the vessel. Do not place the adu close to large objects that may block the signa...

  • Page 41: 3.2.3

    Site preparation 98-136280-b chapter 3: installation 3-5 3333 in stall ati o n 3.2.3 blocking zones — azimuth and elevation in blocking zones the sailor 100 satellite tv might not be able to receive the signal from the satellite. If there is no tv reception you can check whether the antenna is in a ...

  • Page 42: 3.2.4

    Site preparation 3-6 chapter 3: installation 98-136280-b 3.2.4 ship motion and offset from the ship’s motion centre even though it is recommended to mount the adu high, keep the distance between the adu and the ship’s motion centre as short as possible. The higher up the adu is mounted, the higher i...

  • Page 43: 3.2.5

    Site preparation 98-136280-b chapter 3: installation 3-7 3333 in stall ati o n 3.2.5 adu mast design: foundation and height the adu mast must be designed to carry the weight of the adu unit, which is 126 kg (+ the weight of the mast flange). The mast must also be able to withstand on-board vibration...

  • Page 44

    Site preparation 3-8 chapter 3: installation 98-136280-b figure 3-7: adu mast flange, distance to the welded seam caution! Avoid sharp edges where the flange is in direct contact with the radome. Round all edges as much as possible to avoid damaging the surface of the radome. Figure 3-8: adu, bottom...

  • Page 45

    Site preparation 98-136280-b chapter 3: installation 3-9 3333 in stall ati o n mast length and diameter the placement of the adu must ensure a rigid structural connection to the hull or structure of the ship. Parts of the ship with heavy resonant vibrations are not suitable places for the adu. A sma...

  • Page 46

    Site preparation 3-10 chapter 3: installation 98-136280-b sailor 100 satellite tv adu mast length the below tables show the minimum dimensions for a sailor 100 satellite tv adu mast with and without stays or wires. Note that the values are only guidelines - always consider the environment and charac...

  • Page 47

    Site preparation 98-136280-b chapter 3: installation 3-11 3333 in stall ati o n mast with 2 braces max. Free mast length (steel), (m) outer diameter (mm) wall thickness (mm) outer diameter for brace (mm) thickness for brace (mm) 1.2 160 10 80 5.0 1.2 200 5 80 5.0 1.6 180 10 80 5.0 1.6 220 5 80 5.0 2...

  • Page 48: 3.2.6

    Site preparation 3-12 chapter 3: installation 98-136280-b 3.2.6 interference the adu must be mounted as far away as possible from the ship’s radar and high power radio transmitters, because they may compromise the adu performance. Rf emission from radars might actually damage the adu. Radar it is di...

  • Page 49

    Site preparation 98-136280-b chapter 3: installation 3-13 3333 in stall ati o n radar distance the minimum acceptable separation (d min.) between a radar and the adu is determined by the radar wavelength/frequency and the power emitted by the radar. The tables below show some “rule of thumb” minimum...

  • Page 50

    Site preparation 3-14 chapter 3: installation 98-136280-b as long as receiving conditions are favourable, this limited degradation is without importance. However, if receiving conditions are poor – e.G. Due to objects blocking the signal path, heavy rainfall or icing, low satellite elevation and vio...

  • Page 51: 3.2.7

    Site preparation 98-136280-b chapter 3: installation 3-15 3333 in stall ati o n 3.2.7 other precautions condensation and water intrusion if possible, install the radome such that direct spray of seawater is avoided. In some weather conditions there may occur condensation inside the radome. The drain...

  • Page 52: 3.3

    Installation of the adu 3-16 chapter 3: installation 98-136280-b 3.3 installation of the adu the adu is shipped fully assembled. You have to install it on the mast and attach the adu cable. Before installing the adu read the following guidelines. Warning! Use a strong webbed sling with a belt to lif...

  • Page 53: 3.3.1

    Installation of the adu 98-136280-b chapter 3: installation 3-17 3333 in stall ati o n 3.3.1 installing the adu make sure that there is sufficient space underneath the adu to open the service hatch. Through this hatch you access the adu modules for service and maintenance. The adu does not have to b...

  • Page 54

    Installation of the adu 3-18 chapter 3: installation 98-136280-b 4. Attach a webbed, four-part sling with a belt to all 4 lifting brackets. 5. Attach 2 tag lines of suitable length to 2 lifting brackets and man them. 6. With a crane lift the adu off the wooden platform and move it on top of the adu ...

  • Page 55

    Installation of the adu 98-136280-b chapter 3: installation 3-19 3333 in stall ati o n select a suitable size for the cable gland: 16—20 mm diameter or 19—23 mm diameter. See also n-connector interface on the adu on page a-7 for a more detailed drawing how to connect the n-connector on the adu. Ensu...

  • Page 56: 3.3.2

    Installation of the adu 3-20 chapter 3: installation 98-136280-b maximum allowed rf loss in the adu cable maximum allowed cable loss 25 db at 5450 mhz. This is to ensure optimum performance of the system. 3.3.2 opening and removing the service hatch open the hatch to access the antenna modules. The ...

  • Page 57: 3.3.3

    Installation of the adu 98-136280-b chapter 3: installation 3-21 3333 in stall ati o n 3.3.3 grounding the adu the adu must be grounded using the mounting bolts. If the adu cannot or should not be electrically connected directly to the mounting surface, you can use a separate grounding cable to make...

  • Page 58: 3.3.4

    Installation of the acu 3-22 chapter 3: installation 98-136280-b 3.3.4 alternative adu cable preferably choose one of the cable types listed in the table below. Check the data sheet from the cable supplier that both the rf- attenuation and the dc- resistance are kept within the maximum specified val...

  • Page 59: 3.4.2

    Installation of the acu 98-136280-b chapter 3: installation 3-23 3333 in stall ati o n 4. Set the on/off switch at the back of the acu to on. Then you can use the on/off switch at the front panel. Connectors of the acu for a description of the connectors see connector panel — overview on page 4-1. T...

  • Page 60: 3.5

    Installation of the control panel 3-24 chapter 3: installation 98-136280-b ground stud at the acu to ensure that the acu is grounded – also if the adu cable is disconnected from the acu, connect an extra ground wire from the rack to the ground stud on the acu. This ground wire must be a heavy wire o...

  • Page 61: Interfaces

    98-136280-b 4-1 chapter 4 4444 in te rf ac es interfaces 4 this chapter is organised in the following sections: • interfaces of the sailor 100 satellite tv acu • interfaces of the control panel • interfaces of the sailor transmodulator (optional) 4.1 interfaces of the sailor 100 satellite tv acu 4.1...

  • Page 62: 4.1.3

    Interfaces of the sailor 100 satellite tv acu 4-2 chapter 4: interfaces 98-136280-b the connector lan on the front panel is typically connected to the service port at lan3 with a straight ethernet cable. Then you can access the service port from the front of the acu rack version. 4.1.3 dc input conn...

  • Page 63: 4.1.4

    Interfaces of the sailor 100 satellite tv acu 98-136280-b chapter 4: interfaces 4-3 4444 in te rf ac es 4.1.4 adu connector there is just one cable from the acu to the adu. This is used to power the adu, handle all communication between acu and adu, and deliver the rx signal. 4.1.5 rx connector conn...

  • Page 64: 4.1.8

    Interfaces of the sailor 100 satellite tv acu 4-4 chapter 4: interfaces 98-136280-b 4.1.8 nmea 0183 connector (rs-422) connect the ship’s gyro to this connector. (hardware prepared for nmea 2000, for future use) nmea 2000 power: 9-16 vdc. Nmea 2000 len (load equivalency number): 2 (100ma) nmea 0183 ...

  • Page 65: 4.1.9

    Interfaces of the sailor 100 satellite tv acu 98-136280-b chapter 4: interfaces 4-5 4444 in te rf ac es recommended nmea 0183 cable: two-wire constructed with one enclosed shield network signal pair: • size: no. 24 awg (0.24 sq. Mm) or heavier • characteristic impedance: 95 - 140 ohm • propagation d...

  • Page 66: 4.2

    Interfaces of the control panel 4-6 chapter 4: interfaces 98-136280-b 4.2 interfaces of the control panel for a description of the interfaces see the installation manual of the control panel. 4.3 interfaces of the sailor transmodulator (optional) for a description of the interfaces see the installat...

  • Page 67: Connecting Power

    98-136280-b 5-1 chapter 5 5555 connecting power connecting power 5 this chapter is organised in the following sections: • power source • power cable selection • connecting power • power up 5.1 power source there are different options for the power supply: • the 24 vdc ship supply provides power for ...

  • Page 68: 5.2

    Power cable selection 5-2 chapter 5: connecting power 98-136280-b 5.2 power cable selection 5.2.1 source impedance the maximum length of the power cable depends on the type of cable used and the source impedance of the dc power installation in the ship. The maximum allowed source impedance depends o...

  • Page 69: 5.2.3

    Power cable selection 98-136280-b chapter 5: connecting power 5-3 5555 connecting power 5.2.3 power cable recommendations overview the acu is delivered with a power connector (pcb plug-in connector, female plug, weidmuller, part number 1930050000), which accepts wires up to awg10/6 mm 2 . • when ins...

  • Page 70: 5.3

    Connecting power 5-4 chapter 5: connecting power 98-136280-b the length is multiplied by 0.5 above because there are two conductors in the cable. If the tt-6080a power supply is used, use r source = 0 mohm. Examples for using the tt-6080a power supply: awg11 max =0.5 x (60 mohm-0)/4.8 mohm/m = 6.2 m...

  • Page 71: 5.4

    Power up 98-136280-b chapter 5: connecting power 5-5 5555 connecting power 5.4 power up 1. Connect power to sailor transmodulator or multi switch (if installed). 2. Switch on the acu. The unit starts up and goes through an initialization procedure: • acu post • adu initializing • adu post • ready th...

  • Page 72

    Power up 5-6 chapter 5: connecting power 98-136280-b initialisation in daily use once the system is configured and a satellite profile is active, the startup sequence is as follows: • acu post • adu initializing • adu sw upload (if the software versions in the adu and acu are not the same, a softwar...

  • Page 73: Configuration

    98-136280-b 6-1 chapter 6 6666 co n figur ati o n configuration 6 this chapter is organised in the following sections: • introduction to the configuration tools • calibration of the sailor 100 satellite tv • configuration with the web interface • configuration with the control panel • keypad and men...

  • Page 74: 6.1.2

    Introduction to the configuration tools 6-2 chapter 6: configuration 98-136280-b no installation of software is necessary. The web interface is built into the sailor 100 satellite tv acu.The control panel has the application software installed on delivery. You access the web interface from a compute...

  • Page 75: 6.1.3

    Introduction to the configuration tools 98-136280-b chapter 6: configuration 6-3 6666 co n figur ati o n if you cannot establish a connection there might be problems with the proxy server settings of your pc. See proxy server settings in your browser on page 6-10 for further information. For a detai...

  • Page 76: 6.2

    Calibration of the sailor 100 satellite tv 6-4 chapter 6: configuration 98-136280-b 6.2 calibration of the sailor 100 satellite tv you must align the adu with the vessel’s gyro compass. To do this, you make an azimuth calibration, i.E. You determine the offset of the adu zero direction to the bow- t...

  • Page 77

    Calibration of the sailor 100 satellite tv 98-136280-b chapter 6: configuration 6-5 6666 co n figur ati o n fixed heading do not use fixed heading for vessels! Use fixed heading only for fixed installations like remote areas or oil rigs, during training and test. You can enable fixed heading and ent...

  • Page 78

    Calibration of the sailor 100 satellite tv 6-6 chapter 6: configuration 98-136280-b to make an azimuth calibration with user defined input, do as follows: 1. Select user defined in the satellite drop down list. 2. Type in the longitude and polarisation skew of the satellite. The polarisation skew is...

  • Page 79

    Calibration of the sailor 100 satellite tv 98-136280-b chapter 6: configuration 6-7 6666 co n figur ati o n the sailor 100 satellite tv is calibrated now. If the calibration failed there will be a message on the calibration screen. 4 the calibration values could not be saved. Possibly due to defecti...

  • Page 80: 6.3

    Configuration with the web interface 6-8 chapter 6: configuration 98-136280-b 6.3 configuration with the web interface 6.3.1 overview and navigation topics in the web interface use the site map to get an overview over the existing menus, submenus and topics. You can click on each menu in the site ma...

  • Page 81

    Configuration with the web interface 98-136280-b chapter 6: configuration 6-9 6666 co n figur ati o n navigation the web interface consists of the following sections: 1. The navigation pane holds the main menu. Clicking an item in the menu opens a submenu in the navigation pane or a new page in the ...

  • Page 82

    Configuration with the web interface 6-10 chapter 6: configuration 98-136280-b icons in the icon bar the following icons may appear in the icon bar in the web interface: navigating the web interface • to expand a menu , click the menu in the navigation pane. • to access status and settings , click t...

  • Page 83: 6.3.2

    Configuration with the web interface 98-136280-b chapter 6: configuration 6-11 6666 co n figur ati o n 2. Clear the box labeled use a proxy server for your lan . 3. Click ok . When the proxy server settings are disabled, close and restart your browser. You may need to change this setting back on ret...

  • Page 84

    Configuration with the web interface 6-12 chapter 6: configuration 98-136280-b information fields on the dashboard figure 6-6: web interface: dashboard sailor 100 satellite tv parameter description system status current status of the sailor 100 satellite tv . Examples : not ready (waiting for input ...

  • Page 85

    Configuration with the web interface 98-136280-b chapter 6: configuration 6-13 6666 co n figur ati o n tracking polarisation linear polarisation: horizontal, vertical. Circular polarisation: left-hand, right-hand. Tracking rf frequency current rf tracking frequency. Lnb lo frequency high band curren...

  • Page 86: 6.3.3

    Configuration with the web interface 6-14 chapter 6: configuration 98-136280-b 6.3.3 satellite profiles satellite profiles on the page satellite profiles you add, edit and delete satellite profiles. A satellite profile contains all settings that are necessary for a successful reception from the sate...

  • Page 87

    Configuration with the web interface 98-136280-b chapter 6: configuration 6-15 6666 co n figur ati o n 2. Enter or edit the satellite profile name. 3. Select a satellite from the drop down list. This list contains the tv satellites known to the system. If needed, you can add a tv satellite, see tv s...

  • Page 88: 6.3.4

    Configuration with the web interface 6-16 chapter 6: configuration 98-136280-b 5. At lnb lo setup you can set the lnb lo frequencies to the appropriate value for the region covering the satellite profile, see the drop-down list in figure 6-8: web interface: settings, satellite profiles — new entry (...

  • Page 89

    Configuration with the web interface 98-136280-b chapter 6: configuration 6-17 6666 co n figur ati o n to add or edit a tv satellite, do as follows: 1. Go to service > tv satellites and click new satellite or edit next to an existing entry. 2. Enter or edit the satellite name. 3. Enter or edit the l...

  • Page 90: 6.3.5

    Configuration with the web interface 6-18 chapter 6: configuration 98-136280-b 6.3.5 reference satellites reference satellites are used during azimuth adjustment function (see azimuth adjustment on page 6-20). They may also be used for azimuth calibration. When to update the data of a reference sate...

  • Page 91

    Configuration with the web interface 98-136280-b chapter 6: configuration 6-19 6666 co n figur ati o n adding and editing entries in the list of reference satellites editing a pre-installed entry will disable that entry and add a new user-defined entry. The new user-defined entry includes the change...

  • Page 92: 6.3.6

    Configuration with the web interface 6-20 chapter 6: configuration 98-136280-b 2. Enter or edit the fields on the screen. The coverage input field contains a list of comma separated integers. Each integer represents and identifies an area on the earth's surface. Earth's surface has been divided into...

  • Page 93: 6.3.7

    Configuration with the web interface 98-136280-b chapter 6: configuration 6-21 6666 co n figur ati o n further information about azimuth adjustment the purpose of the azimuth adjustment is to significantly reduce the risk of tracking the wrong tv satellite by compensating for errors in the heading i...

  • Page 94

    Configuration with the web interface 6-22 chapter 6: configuration 98-136280-b to define and set a blocking zone, do as follows: 1. Select settings > blocking zones . 2. Select active to enable the blocking zone. Figure 6-16: web interface: settings, blocking zones — azimuth and elevation sailor100i...

  • Page 95

    Configuration with the web interface 98-136280-b chapter 6: configuration 6-23 6666 co n figur ati o n 3. Azimuth: enter start and stop azimuth value in degrees for the blocking zone. Values allowed: 0 to 360 degrees. Enter clockwise. 4. Elevation: enter the start and stop elevation angle for the bl...

  • Page 96: 6.3.8

    Configuration with the web interface 6-24 chapter 6: configuration 98-136280-b 6.3.8 configuring the lan network you can enter a host name. The host name helps identifying the sailor 100 satellite tv system when sending e-mail reports through an external internet connection. The acu has four 10/100 ...

  • Page 97

    Configuration with the web interface 98-136280-b chapter 6: configuration 6-25 6666 co n figur ati o n static ip or dhcp client if you select dhcp client the network ip address and sub-net mask must be provided by a dhcp server on that network. If you select static ip address you must specify a uniq...

  • Page 98

    Configuration with the web interface 6-26 chapter 6: configuration 98-136280-b dns setup if you have access to a domain name server (dns) you can specify the address of the e-mail server by using the server name instead of its ip address. This can be used in outgoing mail server in e-mail setup on p...

  • Page 99: 6.3.9

    Configuration with the web interface 98-136280-b chapter 6: configuration 6-27 6666 co n figur ati o n 6.3.9 e-mail setup to be able to send diagnostics and statistics reports through an external internet connection using e-mail you must set up a couple of parameters. Contact your it department for ...

  • Page 100: 6.3.10

    Configuration with the web interface 6-28 chapter 6: configuration 98-136280-b 6.3.10 sending statistics reports sailor 100 satellite tv can send a statistics report at fixed intervals through an external internet connection. This report contains historical information from the sailor 100 satellite ...

  • Page 101

    Configuration with the web interface 98-136280-b chapter 6: configuration 6-29 6666 co n figur ati o n the following parameters are recorded in the statistics report: parameter recorded description hostname host name, entered in the web interface on the page settings > network. Acu sn acu serial num...

  • Page 102

    Configuration with the web interface 6-30 chapter 6: configuration 98-136280-b processing the statistics report in a spreadsheet application the statistics report is in a data format that can be imported into spreadsheet applications, e.G. Microsoft excel, for further processing. 1. Save the zipped ...

  • Page 103: 6.3.11

    Configuration with the web interface 98-136280-b chapter 6: configuration 6-31 6666 co n figur ati o n 6.3.11 sending a diagnostics report you can send automatically generated diagnostic reports at fixed intervals. The diagnostic report contains information relevant for the service personnel during ...

  • Page 104: 6.3.12

    Configuration with the web interface 6-32 chapter 6: configuration 98-136280-b 6.3.12 upload for uploading new software to the sailor 100 satellite tv see software update on page 8-5. 6.3.13 administration in this section of the web interface you can configure the following administrative settings: ...

  • Page 105

    Configuration with the web interface 98-136280-b chapter 6: configuration 6-33 6666 co n figur ati o n to change the administrator password, do as follows: 1. After entering the administrator user name and password in the administration page, locate the section change administrator logon . 2. Type i...

  • Page 106

    Configuration with the web interface 6-34 chapter 6: configuration 98-136280-b setting up user permissions you can manage user access to certain functions of the sailor 100 satellite tv system. You can allow or deny users that are not administrators access to certain functions and make these pages r...

  • Page 107

    Configuration with the web interface 98-136280-b chapter 6: configuration 6-35 6666 co n figur ati o n importing and exporting a system configuration if you need to reuse a configuration in another sailor 100 satellite tv system, you can save the current configuration to a file, which can then be lo...

  • Page 108

    Configuration with the web interface 6-36 chapter 6: configuration 98-136280-b • heading settings • azimuth adjustment • changes made to the satellite lists (reference satellites and tv satellites) • network setup • user permissions • acu display: brightness setting to reset to factory default setti...

  • Page 109: 6.4

    Configuration with the control panel 98-136280-b chapter 6: configuration 6-37 6666 co n figur ati o n 6.4 configuration with the control panel • getting started • creating or editing a profile • selecting the active profile • deleting a profile • event list • help • about 6.4.1 getting started use ...

  • Page 110: 6.4.2

    Configuration with the control panel 6-38 chapter 6: configuration 98-136280-b to get started with the control panel, do as follows: 1. Make sure that it is connected to the lan port 4 at the rear of the acu, possibly through a switched network. 2. Press the on/off button. A couple of start-up scree...

  • Page 111

    Configuration with the control panel 98-136280-b chapter 6: configuration 6-39 6666 co n figur ati o n . 4. Tap the field satellite . A new window is displayed. Tap and scroll to find the wanted satellite, then tap on a satellite to select it. The list is sorted as follows: 180°w -> 0° -> 180°e. 5. ...

  • Page 112

    Configuration with the control panel 6-40 chapter 6: configuration 98-136280-b • polarisation: select linear or circular depending on the polarisation with which your provider transmits the tv signals 1 . Dvb-s / dvb-s2 : by selecting dvb-s / dvb-s2, it is possible to configure the system to track a...

  • Page 113: 6.4.3

    Configuration with the control panel 98-136280-b chapter 6: configuration 6-41 6666 co n figur ati o n 8. A confirmation window is displayed. Verify the data for the new profile and press ok to close the window. 6.4.3 selecting the active profile to change the active profile, select another profile ...

  • Page 114: 6.4.5

    Configuration with the control panel 6-42 chapter 6: configuration 98-136280-b to delete a profile, do as follows: 1. Tap the menu icon . 2. Select settings . 3. Select delete profile. 4. Tap the profile you want to delete. 5. A confirmation window is displayed. Verify the profile name you want to d...

  • Page 115: 6.4.7

    Configuration with the control panel 98-136280-b chapter 6: configuration 6-43 6666 co n figur ati o n help describes how to handle satellite profiles. Scroll through the help or use the links at the start to jump to a specific topic. 6.4.7 about tap the menu icon , scroll down and tap about . About...

  • Page 116: 6.5

    Keypad and menus of the acu 6-44 chapter 6: configuration 98-136280-b 6.5 keypad and menus of the acu 6.5.1 acu display and keypad in the acu display you can see the current state of the system. You can also see events (warnings, errors and information) and how the system has been configured. Use th...

  • Page 117: 6.5.2

    Keypad and menus of the acu 98-136280-b chapter 6: configuration 6-45 6666 co n figur ati o n 6.5.2 navigating the menus use the keypad to navigate the menus. • press ok or to select a menu item. • use the arrow keys and to go through the menu items or enter a number, digit by digit. • use the arrow...

  • Page 118

    Keypad and menus of the acu 6-46 chapter 6: configuration 98-136280-b top-level menu menu descriptions top-level menu description main view with current status of the sailor 100 satellite tv. This view is displayed after a time out of 10 minutes. Press any key (except left arrow) to enter the menu a...

  • Page 119

    Keypad and menus of the acu 98-136280-b chapter 6: configuration 6-47 6666 co n figur ati o n serial numbers acu: acu serial number; adu: serial number of the antenna network menu description port 1/2 ip current ip address for lan 1 and lan 2. Mask 1/2 current netmask for lan 1 and lan 2. Port 3 ip ...

  • Page 120: 6.5.4

    Keypad and menus of the acu 6-48 chapter 6: configuration 98-136280-b example: event 1/4* : this is the first event out of a list of 4 and there has been a change in the list. Event 1/4 will always be shown, the * indicates that there has been a change. 6.5.4 adjusting brightness of the display to a...

  • Page 121: Installation Check

    98-136280-b 7-1 chapter 7 7777 in stall ati on c hec k installation check 7 now that you have installed the system, you can test it to verify it is ready for customer delivery. Follow the check lists below to test the system for proper operation. • installation check list: antenna • installation che...

  • Page 122

    Installation check list: antenna 7-2 chapter 7: installation check 98-136280-b 7. Make sure that the requirements for mast foundation and height, including flatness, gusset plates and distance from welding seams are met. See adu mast design: foundation and height on page 3-7. 8. Make sure that the d...

  • Page 123: 7.2

    Installation check list: acu, connectors and wiring 98-136280-b chapter 7: installation check 7-3 7777 in stall ati on c hec k 7.2 installation check list: acu, connectors and wiring step task verification and further information done 1. Check that the acu is grounded correctly. See grounding the ac...

  • Page 124: 7.3

    Installation check list: control panel 7-4 chapter 7: installation check 98-136280-b 7.3 installation check list: control panel step task verification and further information done 1. Check that the control panel is connected to the acu at lan 4, possibly through a switched network. If the control pa...

  • Page 125: 7.4

    Installation check list: functional test in harbor 98-136280-b chapter 7: installation check 7-5 7777 in stall ati on c hec k 7.4 installation check list: functional test in harbor step task further information done 1. Check that the antenna is tracking the satellite the tv ready led in the acu disp...

  • Page 126

    Installation check list: functional test in harbor 7-6 chapter 7: installation check 98-136280-b sailor100im.Book page 6 friday, january 18, 2013 10:28 am.

  • Page 127: Service

    98-136280-b 8-1 chapter 8 8888 ser vic e service 8 in this chapter you find the following sections: • getting support: helpdesk • software update • status signalling with leds and status messages • removal and replacement of the acu • removal and replacement of adu modules • troubleshooting sailor10...

  • Page 128: 8.1

    Getting support: helpdesk 8-2 chapter 8: service 98-136280-b 8.1 getting support: helpdesk if this manual does not provide the remedies to solve your problem, contact your service provider. 8.1.1 help desk and diagnostic report during the installation you can enter the support contact for this insta...

  • Page 129

    Getting support: helpdesk 98-136280-b chapter 8: service 8-3 8888 ser vic e event list when an event is registered, the web interface shows an event icon in the icon bar as long as the event is active. The acu display shows also active events. To view the event list with active events, click the eve...

  • Page 130

    Getting support: helpdesk 8-4 chapter 8: service 98-136280-b reset to factory defaults you can reset the sailor 100 satellite tv adu and acu to factory defaults. See resetting to factory default on page 6-35. Important warning! Reset to factory default will delete all settings, including satellite p...

  • Page 131: 8.2

    Software update 98-136280-b chapter 8: service 8-5 8888 ser vic e 8.2 software update 8.2.1 hardware and software requirements (updating adu and acu) the following items are required before the software can be updated: • one computer with a standard ethernet port available. • a standard internet bro...

  • Page 132: 8.2.3

    Software update 8-6 chapter 8: service 98-136280-b the start-up procedure after a software upload takes longer than the usual start-up time, as the software in the adu must also be updated. The acu display shows: adu sw upload . If software upload fails - how to recover to recover from a failed soft...

  • Page 133: 8.3

    Status signalling with leds and status messages 98-136280-b chapter 8: service 8-7 8888 ser vic e 8.3 status signalling with leds and status messages built-in test equipment the adu and the acu have a built-in test equipment (bite) function in order to make fault diagnostics easy during service and ...

  • Page 134: 8.3.1

    Status signalling with leds and status messages 8-8 chapter 8: service 98-136280-b 8.3.1 leds of the adu modules each adu module has a power and a service led. For a list of modules see removal and replacement of adu modules on page 8-10. 8.3.2 leds in the acu the acu has 3 leds: power, tv ready and...

  • Page 135: 8.4

    Removal and replacement of the acu 98-136280-b chapter 8: service 8-9 8888 ser vic e 8.4 removal and replacement of the acu there are no parts in the acu that you can remove or replace. Contact your thrane & thrane service partner for further repair or replacement. Fail/pass led steady red a fault w...

  • Page 136: 8.5

    Removal and replacement of adu modules 8-10 chapter 8: service 98-136280-b 8.5 removal and replacement of adu modules all replacement of modules must be carried out by a thrane & thrane a/s service partner. The figure below shows the modules and their position. Some modules are equipped with leds fo...

  • Page 137

    Removal and replacement of adu modules 98-136280-b chapter 8: service 8-11 8888 ser vic e 5. Zero reference module (x3, 2 in the previous figure, 1 in the next figure) (zrm) (not visible on photo). 6. Dc-motor driver module for elevation (on the bottom side) (ddm). 7. Elevation motor and encoder (no...

  • Page 138

    Removal and replacement of adu modules 8-12 chapter 8: service 98-136280-b 15. Dc-motor driver module for azimuth (ddm). 16. Azimuth motor (not visible on photo). 17. Azimuth encoder (not visible on photo). 18. Rotary joint (not visible on photo). 19. Feed horn. Before contacting your service partne...

  • Page 139: 8.6

    Troubleshooting 98-136280-b chapter 8: service 8-13 8888 ser vic e 8.6 troubleshooting 8.6.1 overview this section describes an initial check of the primary functions of the sailor 100 satellite tv system, and provides some guidelines for troubleshooting, if one of the checks should fail. Generally,...

  • Page 140

    Troubleshooting 8-14 chapter 8: service 98-136280-b sailor100im.Book page 14 friday, january 18, 2013 10:28 am.

  • Page 141

    Appendices sailor100im.Book page 1 friday, january 18, 2013 10:28 am.

  • Page 142

    Sailor100im.Book page 2 friday, january 18, 2013 10:28 am.

  • Page 143: Technical Specifications

    98-136280-b a-1 appendix a aaaa te ch n ic al specific ati o n s technical specifications a a.1 sailor 100 satellite tv system components a.1.1 general specifications item specification frequency band rx ku-band 10.70 to 12.75 ghz reflector size 103 cm (40 inch) certification (approval) compliant wi...

  • Page 144: A.1.2

    Sailor 100 satellite tv system components a-2 appendix a: technical specifications 98-136280-b a.1.2 adu item specification dimensions (overall) diameter x height: Ø 130 cm (51.3 inch) x h 150 cm (58.9 inch) weight 126 kg (278 lbs) antenna type, pedestal 3-axis (plus skew) stabilised tracking adu wi...

  • Page 145

    Sailor 100 satellite tv system components 98-136280-b appendix a: technical specifications a-3 aaaa te ch n ic al specific ati o n s vibration, survival sine: iec 945 (8.7.2) dwell, mil-std-167-1 (5.1.3.3.5) dwell. Random: maritime survival shock mil-std-810f 516.5 (proc. Ii) temperature (ambient) o...

  • Page 146: A.1.3

    Sailor 100 satellite tv system components a-4 appendix a: technical specifications 98-136280-b a.1.3 acu a.1.4 control panel and sailor transmodulator for technical specifications see the documentation provided with the control panel. For technical specifications see the documentation provided with ...

  • Page 147: A.2

    Outline drawings 98-136280-b appendix a: technical specifications a-5 aaaa te ch n ic al specific ati o n s a.2 outline drawings a.2.1 adu figure a-1: outline drawing: adu sailor100im.Book page 5 friday, january 18, 2013 10:28 am.

  • Page 148: A.2.2

    Outline drawings a-6 appendix a: technical specifications 98-136280-b a.2.2 acu figure a-2: outline drawing: acu sailor100im.Book page 6 friday, january 18, 2013 10:28 am.

  • Page 149: A.2.3

    Outline drawings 98-136280-b appendix a: technical specifications a-7 aaaa te ch n ic al specific ati o n s a.2.3 n-connector interface on the adu figure a-3: n-connector interface on the adu sailor100im.Book page 7 friday, january 18, 2013 10:28 am.

  • Page 150

    Outline drawings a-8 appendix a: technical specifications 98-136280-b sailor100im.Book page 8 friday, january 18, 2013 10:28 am.

  • Page 151: Grounding and Rf Protection

    98-136280-b b-1 appendix b bbbb gr ounding and rf grounding and rf protection b b.1 why is grounding required? B.1.1 reasons for grounding grounding the sailor 100 satellite tv system is required for at least two reasons: • safety: lightning protection of persons and equipment. • protection: esd (el...

  • Page 152: B.2

    Grounding recommendations b-2 appendix b: grounding and rf protection 98-136280-b b.2 grounding recommendations b.2.1 grounding the acu the acu should be grounded to the ship/hull. For this purpose you may use a short adu cable and a grounding kit. Further, the acu must be grounded at its grounding ...

  • Page 153: B.2.2

    Grounding recommendations 98-136280-b appendix b: grounding and rf protection b-3 bbbb gr ounding and rf per used jumper cable the maximum cable length of the cable to the antenna is reduced by: • enviroflex 400: 1.25 m • spuma 400-fr: 6 m • sucofeed 1/2" fr: 10 m b.2.2 grounding the adu you can gro...

  • Page 154: B.3

    Alternative grounding for steel hulls b-4 appendix b: grounding and rf protection 98-136280-b b.3 alternative grounding for steel hulls the following guidelines assume a two-wire, isolated grounding arrangement; that is no part of the circuit, in particular the battery negative, is connected to any ...

  • Page 155

    Alternative grounding for steel hulls 98-136280-b appendix b: grounding and rf protection b-5 bbbb gr ounding and rf figure b-3: grounding at a dedicated rf ground (alternative) $qwhqqdjurxqghg zlwkvhsdudwhfdeoh $qwhqqd 0dvw hohfwulfdoo\erqghg wrwkhvwhhokxoo %dvh3odwh $qwhqqdlvrodwhg iurpwkhwkhkxoo ...

  • Page 156: B.4

    Alternative grounding for aluminum hulls b-6 appendix b: grounding and rf protection 98-136280-b b.4 alternative grounding for aluminum hulls the following guidelines assume a two-wire, isolated grounding arrangement; that is no part of the circuit, in particular the battery negative, is connected t...

  • Page 157

    Alternative grounding for aluminum hulls 98-136280-b appendix b: grounding and rf protection b-7 bbbb gr ounding and rf proximity to the shielded coax cable hence connecting the adu to the acu grounding kit. A heavy gauge wire with tinned strands (min. 6 mm 2 ) can be used for this purpose. Figure b...

  • Page 158: B.5

    Alternative grounding for fibre glass hulls b-8 appendix b: grounding and rf protection 98-136280-b b.5 alternative grounding for fibre glass hulls b.5.1 grounding the acu the acu should preferably be grounded with the short adu cable and a grounding kit (available from thrane & thrane). Further, th...

  • Page 159: B.6

    Separate ground cable 98-136280-b appendix b: grounding and rf protection b-9 bbbb gr ounding and rf b.6 separate ground cable b.6.1 ground cable - construction when dealing with electrical installations in a marine environment, all wiring must be done with double insulated, tinned strands, high qua...

  • Page 160: B.6.2

    Separate ground cable b-10 appendix b: grounding and rf protection 98-136280-b b.6.2 ground cable - connection mount the ground cable close to and parallel to the shielded coax cable thus minimizing ground loop problems. If possible, route the coax cable and the ground cable in metal conduits bonded...

  • Page 161

    Separate ground cable 98-136280-b chapter b: grounding and rf protection b-11 bbbb gr ounding and rf the ground cable must be connected at one of the mounting/grounding bolts on the adu as illustrated below. Remember to seal the joint with protective coating to avoid corrosion. Figure b-8: adu isola...

  • Page 162: B.7

    Jumper cable for grounding b-12 chapter b: grounding and rf protection 98-136280-b b.7 jumper cable for grounding figure b-9: jumper cable for grounding (specifications) sailor100im.Book page 12 friday, january 18, 2013 10:28 am.

  • Page 163: B.8

    Rf interference 98-136280-b chapter b: grounding and rf protection b-13 bbbb gr ounding and rf b.8 rf interference interference induced from nearby high-power rf transmitters might cause system failures and in extreme cases permanent damage to the sailor 100 satellite tv equipment. If there are prob...

  • Page 164

    Rf interference b-14 chapter b: grounding and rf protection 98-136280-b sailor100im.Book page 14 friday, january 18, 2013 10:28 am.

  • Page 165: System Messages

    98-136280-b c-1 appendix c cccc sy st em me ss age s system messages c c.1 event messages — overview the sailor 100 satellite tv detects events during • post (power on self test) — a self test performed at every power-up. • past (person activated self test) — started in the web interface • cm (conti...

  • Page 166: C.2

    List of adu events c-2 appendix c: system messages 98-136280-b c.2 list of adu events error code (id) unit severity description explanation 0a001-0 antenna error production data production data is invalid. 0a002-0 antenna error xim internal antenna configuration data stored in the pcm module is inva...

  • Page 167

    List of adu events 98-136280-b appendix c: system messages c-3 cccc sy st em me ss age s 0a018-0 antenna error ism abs device cannot initialise the ism info: 0x00000000: device not found (possible cabling problem) 0x000cbbaa: device internal error (replace device) aa=status, bb=state, c=calibration ...

  • Page 168

    List of adu events c-4 appendix c: system messages 98-136280-b 0a034-0 antenna warning acu communication the communication link between acu and antenna is down. 0a035-0 antenna warning ism data valid sensor measurements from the ism are invalid. This indicates a malfunctioning ism. 0a036-0 antenna w...

  • Page 169

    List of adu events 98-136280-b appendix c: system messages c-5 cccc sy st em me ss age s 0a049-0 antenna warning azi encoder slip a slip of the azimuth encoder has been detected. No user interaction is required unless this is a permanent situation. In this case the belt and encoder of the azimuth ax...

  • Page 170

    List of adu events c-6 appendix c: system messages 98-136280-b 0a057-0 antenna warning ele ddm warning the elevation motor controller has temporarily observed an unusual situation with regards to temperature, voltage, current or velocity. No user interaction required. 0a058-0 antenna warning pmm war...

  • Page 171: C.3

    List of acu events 98-136280-b appendix c: system messages c-7 cccc sy st em me ss age s c.3 list of acu events error code (id) acu pcb severity description explanation 08060-0 adm warning adu modem acu/adu communication error detected (framing and parity). If the situation is persistent, check if c...

  • Page 172

    List of acu events c-8 appendix c: system messages 98-136280-b 08072-0 adm error user defined satellite data there is an error in the satellite database. The data describing the satellite selected in the active satellite profile is corrupt. Edit the respective user defined satellite entry and correc...

  • Page 173

    List of acu events 98-136280-b appendix c: system messages c-9 cccc sy st em me ss age s 0810b-0 adm error adu software version some error occurred during upload of software to the adu, which means that the adu software version is not as expected. Either the software in the acu, does not meet the mi...

  • Page 174

    List of acu events c-10 appendix c: system messages 98-136280-b sailor100im.Book page 10 friday, january 18, 2013 10:28 am.

  • Page 175: Glossary

    98-136280-b glossary-1 4444 glo ss ar y glossary glossary 4 a abs adu bus slave acu antenna control unit adm acu digital module. A main processor board in the acu. Amb antenna module bus c ce conformité européenne. This term signifies that a ce certified product conforms to european health, environm...

  • Page 176

    Glossary glossary-2 98-136280-b h hdt heading true, nmea sentence. Hh horizontal high hl horizontal low i iec international electrotechnical commission. The international standards and conformity assessment body for all fields of electrotechnology. Ism inertial sensor module k kdm keyboard and displ...

  • Page 177

    Glossary 98-136280-b glossary-3 4444 glo ss ar y p past person activated self test pcm pedestal control module pmm polarisation motor module post power on self test. A system test that is activated each time the system is powered on. Psm power supply module r rf radio frequency. Electromagnetic wave...

  • Page 178

    Glossary glossary-4 98-136280-b sailor100im.Book page 4 friday, january 18, 2013 10:28 am.

  • Page 179: Index

    98-136280-b index-1 5555 inde x index index 5 a access limit , 6-34 acu description , 2-7 led , 8-7 acu display description , 6-44 acu events , c-7 acu interfaces , 2-8 acu rack version connector panel, overview , 4-1 grounding , 3-23 installing , 3-22 leds, display and keypad , 4-1 administration s...

  • Page 180

    Index index-2 98-136280-b calibration azimuth , 6-4 elevation , 6-5 error codes , 6-6 satellite data , 6-17 calibration data , 6-36 reset , 6-36 change administrator password , 6-33 change network , 6-34 compass safe distance , a-4 condensation in antenna , 3-15 configuration copy , 6-35 export , 6-...

  • Page 181

    Index 98-136280-b index-3 5555 inde x events acu , c-7 adu , c-2 display in control panel , 6-42 list of active , 8-3 export configuration , 6-35 f factory default calibration data , 6-36 reset , 6-35 factory defaults reset to , 8-4 failure states view , 8-13 features , 2-2 fiberglass hulls groundin...

  • Page 182

    Index index-4 98-136280-b lock service hatch , 3-20 locking pin , 2-5 , 8-11 log off administrator , 6-33 logon administrator, web interface , 6-32 m mail server setup , 6-27 mast 2 braces , 3-11 3 braces , 3-10 design , 3-7 flange thickness , 3-7 flatness , 3-7 foundation , 3-7 gusset plates , 3-7 ...

  • Page 183

    Index 98-136280-b index-5 5555 inde x r radar distance from antenna , 3-12 signal degradation , 3-14 reference satellite , 6-18 remove service hatch , 3-20 report send by e-mail , 6-27 reset , 6-48 , 8-4 factory default , 6-35 password , 6-33 reset administrator password , 6-33 reset keys on acu , 6...

  • Page 184

    Index index-6 98-136280-b system configuration copy , 6-35 system messages , c-1 t technical data , a-1 terminal grounding recommendations , b-2 tnc connector , 4-3 tools needed , 3-2 tracking properties , 6-15 , 6-39 tracking type , 6-15 dvb-s , 6-15 troubleshooting diagnostic report , 8-2 tt numbe...

  • Page 186

    Info@thrane.Com • thrane.Com 98-136280-b.