Sailor 6217 VHF Installation Manual
What’s in the box?
How to install the VHF on desktop and overhead
How to install the VHF flush mount
INSTALLATION GUIDE
SAILOR 6217 VHF DSC - AIS Receiver
Drilling plan on desktop and overhead
99-130249
4 x M4 or hole for
self-tapping ø3.9
150mm
53
mm
71mm
196mm
23mm
9mm
Tilting ±20°
Note!
- Firmly tie back and secure any wires not used in order to
avoid possibility for mutual shorting or shorting to ground!
- To ensure waterproof sealing:
If the surface isn’t plane and/or rigid remove the gasket and
seal with silicone sealant between the VHF and the surface.
U-Mounting
Bracket
Transceiver
Gasket
Flush Mount
Bracket (2 pcs.)
Sun Screen
Fuse
6.3x3.2mm (10AT)
Hand Microphone
Cradle
Wheel Knob
(2 pcs.)
Screw M4x45
TORX 20
(5 pcs.)
Square Nut
M4x7x2.2
(5 pcs.)
Screw M4x12
TORX 20 (3 pcs.)
Screw ø3.9x19
TORX 20 (3 pcs.)
Screw M4x12
TORX 20
(5 pcs.)
Screw ø3.9x19
TORX 20
(5 pcs.)
Power Cable
Connection Cable,
1 m
Cable assembly for waterproof installation
1.
2.
3.
4.
Connect the 4 cable connections with rubber vulcanizing tape as shown .....
Cap for LTW BD/BU
Connector
(2 pcs.)
What’s in the box?
How to install the VHF on desktop and overhead
How to install the VHF flush mount
INSTALLATION GUIDE
SAILOR 6217 VHF DSC - AIS Receiver
A
A
B
B
99-130248
Gasket
Flush Mount Bracket (2 pcs.)
Screw M4x45 TORX 20 (4 pcs.)
Connect to LOUD HAILER
(RED isolation on inner connector)
Connect to EXT. SPEAKER
(WHITE isolation on inner connector)
Connect to POWER +
(RED wire)
Connect to POWER -
(BLUE wire)
Square Nut M4x7x2.2 (4 pcs.)
Max wall thickness 26mm
Drilling plan on desktop and overhead
Very important information!
99-130249
4 x M4 or hole for
self-tapping ø3.9
150mm
53
mm
71mm
196mm
23mm
9mm
Tilting ±20°
Do not remove the membrane.
If you remove the membrane the radio will not be waterproof.
Note!
- Firmly tie back and secure any wires not used in order to
avoid possibility for mutual shorting or shorting to ground!
- To ensure waterproof sealing:
If the surface isn’t plane and/or rigid remove the gasket and
seal with silicone sealant between the VHF and the surface.
U-Mounting
Bracket
Transceiver
Gasket
Flush Mount
Bracket (2 pcs.)
Sun Screen
Fuse
6.3x3.2mm (10AT)
User & Installation Manual
Hand Microphone
Cradle
Wheel Knob
(2 pcs.)
Screw M4x45
TORX 20
(5 pcs.)
Square Nut
M4x7x2.2
(5 pcs.)
Screw M4x12
TORX 20 (3 pcs.)
Screw ø3.9x19
TORX 20 (3 pcs.)
Screw M4x12
TORX 20
(5 pcs.)
Screw ø3.9x19
TORX 20
(5 pcs.)
USER & INSTALLATION MANUAL
SAILOR 6217 VHF DSC - AIS Receiver
Power Cable
Connection Cable,
1 m
Cable assembly for waterproof installation
1.
2.
3.
4.
Connect the 4 cable connections with rubber vulcanizing tape as shown .....
Membrane
Cap for LTW BD/BU
Connector
(2 pcs.)
Brown, Pin 1, NMEA in+
Blue, Pin 2, NMEA in-
For waterproof installation use
rubber vulcanizing tape
White, Pin 3, NMEA out-
Green, Pin 4, NMEA out+
GPS Cable (NMEA 0183)/
Chart Plotter Cable
Chart Plotter
GPS
99-131043-B
Note!
Firmly tie back and secure any wires not used in order to avoid
possibility for mutual shorting or shorting to ground!
Pin assignments
Front View
Wire color
Pin
Brown
1
Blue
2
White
3
Green
4
Yellow
5
Grey
6
Pink
7
Red
8
1
2
9
8
7
6
10
3
4
5
Black
9
10
Orange - SCREEN (Drain)
NMEA in+
NMEA in-
NMEA out-
NMEA out+
Mike 2 / Line in
EAR 2 / Line out
Hook_PTT
Battery Supply when radio is on
Internal GND = - Battery
Internal GND = - Battery
Description
99-130891-B
How to install the GPS and the Chart Plotter - Cable connections
Pin assignments
Front View
Wire color
Pin
Brown
1
Blue
2
White
3
Green
4
Yellow
5
Grey
6
Pink
7
Red
8
1
2
9
8
7
6
10
3
4
5
Black
9
10
Orange - SCREEN (Drain)
NMEA in+
NMEA in-
NMEA out-
NMEA out+
Mike 2 / Line in
EAR 2 / Line out
Hook_PTT
Battery Supply when radio is on
Internal GND = - Battery
Internal GND = - Battery
Description
99-130891-B
Installation Guide
User & Installation Manual
USER & INSTALLATION MANUAL
SAILOR 6217 VHF DSC - AIS Receiver
Very important information!
Do not remove the membrane.
If you remove the membrane the radio will not be waterproof.
Membrane
How to prevent water ingress
Connector for Hand Microphone or Handset - If not used, put the cap
from the ACC connector on the front connector to prevent water ingress.
Dimensions for the VHF
A
A
B
B
99-130248
Gasket
Flush Mount Bracket (2 pcs.)
Screw M4x45 TORX 20 (4 pcs.)
Connect to LOUD HAILER
(RED isolation on inner connector)
Connect to EXT. SPEAKER
(WHITE isolation on inner connector)
Connect to POWER +
(RED wire)
Connect to POWER -
(BLUE wire)
Square Nut M4x7x2.2 (4 pcs.)
Max wall thickness 26mm