- DL manuals
- Saleen
- Kitchen Appliance Accessories
- 10-8002-C11790A
- Installation Manual
Saleen 10-8002-C11790A Installation Manual
Summary of 10-8002-C11790A
Page 1
= saleen speedlab suspension kit installation manual: 2005 mustang p/n: 10-8002-c11790a saleen performance, inc. 76 fairbanks irvine, ca 92618 949-597-4900 www.Saleen.Com.
Page 2: Or Technician
2 if you are not experienced in the area of automotive mechanics, we strongly urge that you refer this installation to a certified installer or technician.
Page 3
3 saleen speedlab suspension kit installation guide for 2005 mustang welcome! Thank you for buying the saleen speedlab suspension kit for the 2005 mustang. We appreciate your business, and we hope you enjoy your product. For your benefit, please read the following instructions completely and thoroug...
Page 4
4 table of contents saleen chassis fasteners and torques…………………………………..6 i wheel removal…………………………………….…………….………7 ii front struts removal………………………………………..…...…….8 iii front sway bar removal……………………………………..…...….10 iv front strut subassembly…………………………………….…...…...11 v front and rear shock decal insta...
Page 5
5 obtain the following tools: • spring compressor • 10 mm wrench • ¼” wrench • ½” drive ft-lb torque wrench • ½” drive impact gun • ½” drive 13/16” deep socket • ½ ” drive 13mm deep socket • ½ ” drive 15mm deep socket • ½ ” drive 15 mm shallow wobbly socket • ½” drive 18mm deep socket • ½ ” drive 21...
Page 6
6 the following table lists the proper torque values to follow when fastening all suspension components; note also the recommendations for the use of loctite in the last column. Saleen chassis fasteners and torques ref number (b)olt (n)ut (f)itting qty joint description min spec torque (nm) nom spec...
Page 7
7 i wheel removal figure 1 order of operations: 1. Jack up the front of the car, and place jack stands underneath the chassis members. 2. Lower the car onto the jack stands. The car should stay in this position for the entire front suspension replacement. 3. Remove five 13/16” nuts using the 1/2” ai...
Page 8
8 ii front struts removal figure 1 order of operations: note: keep all hardware for installation of new suspension components. 1. Remove the two lower strut bolts using a 3/8” impact gun with a 18mm deep socket. (figures 1 and 2) 2. Unbolt the end link from the strut using the 3/8” impact gun with t...
Page 9
9 figure 5 3. Unbolt the brake line from the strut using the 3/8” impact with the 10mm socket. Remove the christmas tree that holds the abs line in place. (figure 4) 4. Using the 13 mm deep socket and 3/8” drive impact gun, remove the nuts from the four upper strut bolts (in the engine bay). (figure...
Page 10
10 iii front sway bar removal figure 1 figure 2 order of operations: note: keep all hardware for installation of new suspension components. 1. Remove the bolt that connects the sway bar to each end link using a 3/8” impact gun with the 18mm socket. (figure 1) 2. Remove the four bolts under the chass...
Page 11
11 iv front strut subassembly part number description qty. 06-1302-c09816a strut front coupe 2 06-1302-c09731a spring front coupe 2 figure 1 figure 2 order of operations: note: the following operation is dangerous. If you have not successfully completed the subbassembly of a strut before, leave the ...
Page 12
12 figure 4 figure 5 4. Obtain the bump stop from the stock strut, and cut it with a hack saw at the line shown in figure 3 (bump stop on the right in figure 3 is before, and the one on the left after, the cut has been made). 5. Obtain the new shock and spring. Place modified bump stop over the shoc...
Page 13
13 v front and rear shock decal installation part number description qty. 06-1302-c09816 strut front coupe 2 06-1302-b09916* shock rear coupe 2 06-9101-c10227 decal shock n2 racecraft 4 figure 1 figure 2 order of operations: 1. Take the shock, position it as shown in figure 1, and place the logo as ...
Page 14
14 vi front struts installation part number description qty. 06-1302-b09913* strut front assembly coupe 2 figure 1 figure 2 order of operations: 1. With notch facing outside of the vehicle, slide studs in top of strut into four upper mounting holes; be sure the brake line sits behind strut assembly ...
Page 15
15 vii front sway bar subassembly part number description qty. 06-1303-c09503 swaybar front 1 00-1303-c09515* bushing swaybar front 2 00-1303-c09932* bracket bushing swaybar front 2 figure 1 figure 2 order of operations: 1. Grease the bushings. (figures 1 and 2) 2. Push bushings in towards the idle ...
Page 16
16 viii front sway bar installation part number description qty. 06-1303-b09915* swaybar front assembly 1 figure 1 figure 2 order of operations: 1. Put the new sway bar into the location where the stock sway bar went. 2. Align the bushing brackets over the existing studs. (figure 2) 3. Fasten down t...
Page 17
17 ix rear suspension removal figure 1 order of operations: note: keep all hardware and rubber spring boots for installation of new suspension components. 1. Jack up the rear of the car and place jack stands under the chassis members near the rear suspension. 2. Lower the car onto the jack stands an...
Page 18
18 figure 3 6. Let the axle hang. Note the orientation of the rear springs, how there is a shortened vertical distance between each of the coils at the top of the spring. 7. Work the springs out of place. Pop the bottom end toward the front of the vehicle, and pull the spring out. (figure 2) 8. In t...
Page 19
19 x rear suspension installation part number description qty. 06-1302-c09818 shock rear coupe 2 06-1302-c09819 spring rear coupe 2 figure 1 figure 2 order of operations: 1. Place the top of the spring (the end with the shorter vertical distance between coils) into the mounting location, making sure...
Page 20
20 4. The bump stop has to be modified. Figure 3 shows the unmodified bump stop with the proper cut line, and figure 4 shows the modified bump stop. 5. With a hack saw, cut both rear bump stops at the cut line, in the bottom of the two rings in the bump stop molding. 6. Reinstall the stock sway bar....