Summary of SOD 12
Page 1
Instructions and warranty model no: sod 12.
Page 2
2 salton gas patio heater.
Page 3
3 1. Important safeguards caution please read carefully the following safety guidelines before operationing this appliance. Do not use the patio heater for indoors, as it may cause personal injury or property damage. This outdoor heater is not intended to be installed onto recreational vehicles and/...
Page 4
4 important…flash back (i.E. Fire in the burner jet) in the event of a flash back occurring in the burner tube (that is when the flame burns inside the jet instead of the outside): immediately turn off the gas supply at the gas cylinder. Turn the patio heater itself off at the control switches. Disc...
Page 5
5 3. Gas requirements use lpg gas only. The pressure regulator and hose assembly to be used must conform to local standard codes. The installation must conform to local codes, or in the absence of local codes, with the standard for the storage and handling of liquid petroleum gases. A dented, rusted...
Page 6
6 note if the new cylinder has just been connected, please allow at-least one minute for the air in the gas pipeline to purge out through the pilot hole. When lighting the pilot flame, ensure that the variable control knob is continuously pressed down while pressing the igniter button. The variable ...
Page 7
7 6. Cleaning and care wipe off powder coated surfaces with soft, moist rag. Do not clean heater with cleaners that are combustible or corrosive. Remove debris from the burner to keep it clean and safe for use. Cover the burner unit with the supplied protective cover when the heater is not in use. 7...
Page 8
8 a. Construction and characteristics transportable terrace/garden heater with cylinder housing casing in steel with powder-coating or stainless steel gas hose connections with metal clamp (screw caps for germany) stainless steel flame screen heat emission from reflector b. Specifications for outdoo...
Page 9
9 9. Assembly procedures step 1 put the 3 pcs post brackets on each position on the base as shown in the picture. Use 3 pcs m8 x 16 mm bolts to join the post brackets and stand. Step 2 put the post on the top of 3 pcs post brackets. Use 6 pcs m6 x 35 mm bolts and nuts to connect the post to the 3 pc...
Page 10
10 step 3 place the tank housing on the stand. Step 4 fit the gas hose/pipe nut to the burner gas inlet connector. Tighten the gas hose/pipe nut and gas inlet thread. Fix the completed burner unit to the post by 4 pcs m6 x 10 mm bolts. Tank housing bolt.
Page 11
11 step 5 check whether the connection of vertical post and burner are assembled according to instructions, and all bolts and nuts are tightened. Put washer Ø8 mm on each reflector support bolt. Step 6 fasten the reflector with 3 pcs washers and 3 pcs m8 mm dome nuts. Reflector flat washer nut refle...
Page 12
12 step 7 bring up the tank housing and rest it on the post plate. Connect the regulator to the gas tank and tighten it with adjustable wrench. Connect the end thread of inlet gas hose to the regulator. Put lpg gas tank on the stand. Gas cylinder regulator.
Page 13
13 10. Maintenance and servicing instructions there is very little maintenance required on this appliance. Important points to remember are: always check that the regulator seal is undamaged when changing the gas cylinder. Always check that the hose is in good condition before using and that it is s...
Page 14
14 11. Problems check list problem probable cause solution pilot flame will not light gas valve may be off turn the valve on tank fuel is empty refill the lpg tank opening is blocked clean or replace the opening air in supply system purge air from the lines loose connections check all fittings pilot...
Page 15
15 please affix your proof of purchase/receipt here in the event of a claim under warranty this receipt must be produced. W a r r a n t y 1. Tedelex trading (pty) limited (“tedelex”) warrants to the original purchaser of this product (“the customer”) that this product will be free of defects in qual...