1. DL manuals
  2. Salus
  3. Thermostat
  4. RXRT505
  5. Instruction Manual

Salus RXRT505 Instruction Manual

Summary of RXRT505

  • Page 1

    R rt 5 0 5r f 5 t t t t 5 5 5 r r r r r r r r r rt t f f r r r r 5 5 5 5 5 5 5 5 5 5 r r r r r r 5 5 rt5 0 05r f 0 0 5 rt t r r r r r r r f f f 5r r r r r 5 0 0 0 t t50 5rf t t t r r r rf f f 0 0 0 5 5 r rt 5 rt5 rt5 rt5 rt5 rt5 rt5 rt5 rt5 rt rt rt rt rt rt rt5 5 5 5 5 5 05r f f f f f f f f f f 5 5...

  • Page 2

    St325tx 0915fltx st625tx 0915flt rt305tx rt505tx supplied seperately.

  • Page 3

    Rxrt505 rxwbc605 rxvbc605 r r x x s s t t 6 6 2 2 5 5.

  • Page 4: Product Compliance

    Product compliance this product complies with the essential requirements of the following ec directives: • electro-magnetic compatibility directive 2004/108/ec • low voltage directive 2006/95/eec • ec marking directive 93/68/eec safety information these instructions are applicable to the salus contr...

  • Page 5: Rt Receiver

    Rt receiver introduction the rxrt505 is used for the wiring connections and on/off control. The rxrt505 is linked to your thermostat via radio frequency (rf) signal. Features • led status indication • on / off switch • 868 mhz communication connecting the rxrt505 receiver the rt receiver should be m...

  • Page 6: Receiver Wiring Terminals

    On the front cover of the receiver you will see that there is the on/off switch and two light emitting diodes (leds). The switch allows you to turn off the receiver if necessary to prevent it calling for heat. The top led (red) will illuminate when the switch is in the ‘on’ position and the unit is ...

  • Page 7: Your Thermostat

    Rxrt505 instruction manual 7 setting up rf communication with your thermostat rt505tx / rt305tx after you have switched the receiver on, the thermostat will automatically pair* with the rt505tx and the rt305tx (only). When the red led stops flashing, the unit has successfully paired. If you have dif...

  • Page 8: S-Series Receivers

    S-series receivers introduction the rxst625 is used for the wiring connections and on/off control. The rxst625 is linked to your thermostat via radio frequency (rf) signal. Features • led status indication • manual override • 868 mhz communication connecting the rxst625 receiver the rt receiver shou...

  • Page 9: Typical Wiring Installations

    Typical wiring installations the rxst625 receiver is wired the same way no matter if you are wirings 240v or 24v, the receiver will always need a 240v live and neutral feed connected into l & n terminals. The com and no is to be connected to the boilers external loop (see diagram below), if connecte...

  • Page 10: Receiver Led Indicators

    Receiver led indicators the led indicators on the rxst625 receiver are designed to give a clear and easily understood indication of the current state of the system. The various led signal combinations and descriptions of what they indicate are shown in the table below: led state indication blue on r...

  • Page 11: Key/operation

    The status of the rxst625 receiver is indicated by the use of two bi- colour light emitting diodes (leds). The status indicators are: user control function summary key/operation functions auto sets receiver to automatic mode (default setting) manual sets receiver to manual mode on turns relay output...

  • Page 12: Manual Mode

    Manual mode moving the slide switch to the ‘manual’ position selects the manual operation mode of the rf receiver. In manual mode, the receiver ignores the rf signal from the thermostat and controls the output relay manually, based on the setting of the failsafe mode switch. Failsafe modes failsafe ...

  • Page 13: Rxvbc605 Receiver

    Rxvbc605 receiver introduction the rxvbc605 is an integral plug-in rf boiler control. The rf boiler control is a direct replacement for the basic time clock or blanking plate usually supplied with the boiler. Installing the rf boiler control takes minutes. Once installed, you will benefit from all t...

  • Page 14: Control to The Boiler

    Mounting the rf integral boiler control to the boiler danger! • 24v & 230v: do not touch electrical components or circuits • isolate mains electricity supply before starting any work and observe all relevant safety precautions. • follow electro static discharge precaution. Do not touch any visible p...

  • Page 15

    4. Before switching the boiler on at its mains supply, ensure the module switch is in the off position. 5. To ensure the boiler control is connected properly, please now move the switch to on . The boiler should now go on and the led on the your boiler control should illuminate. 6. Now move the swit...

  • Page 16: Your Thermostat

    Setting up rf communication with your thermostat 1. Ensure the switch on the rf integral boiler module is in the auto 2. Gently press and hold the sync button with a blunt object. After 3 seconds the boiler control led will flash once every second to indicate it is ready to pair and ready to receive...

  • Page 17: User Controls

    User controls integral rf boiler control a – led this led will be on when the thermostat is demanding heat. B – mode switch on – boiler will be on continuous auto – will follow instructions from the thermostat off – boiler is off c – sync button - this is used only for pairing the rf communications....

  • Page 18: Rxwbc605 Receiver

    Rxwbc605 receiver introduction the rxwbc605 comprises of an integral plug-in rf boiler control. The rf boiler control is a direct replacement for the basic time clock or blanking plate usually supplied with the boiler. Installing the rf boiler control takes minutes. Once installed, you will benefit ...

  • Page 19: Rf Transmission

    Rf transmission the receiving range between your thermostat and the rf boiler control is around 100 metres in open air, however many factors can affect the rf transmission and shorten the operating distance, e.G. Shielding by thick walls, foil back plasterboard, metal objects such as filing cabinets...

  • Page 20

    4. First plug in the connector block c ensuring correct orientation. Remember to ensure the block is fully connected. 5. Now locate the boiler control’s four hooks then press in and down. Replace cover panel a. 6. Replace the front fascia and boiler’s outer casing c a rxwbc605 instruction manual 20

  • Page 21

    7. Before switching the boiler on at its mains supply, ensure the module switch is in the off position . 8. To ensure the boiler control is connected properly, please now move the switch to on . The boiler should now fire and the led on the your boiler control should illuminate 9. Now move the switc...

  • Page 22: Rf Boiler Control

    Rf boiler control when the switch on the boiler module is in the auto position, the boiler control will automatically receive the rf signal from the thermostat and control the module output so that it switches the boiler accordingly. The user can also move the switch to the manual on position; when ...

  • Page 23: User Controls

    User controls integral rf boiler control a – led this led will be on when the thermostat is demanding heat. B – mode switch on – boiler will be on continuous auto – will follow time and temperature program in the transmitter off – boiler is off c – sync button - this is used only for pairing the rf ...

  • Page 24: Environment

    Technical specification rxrt505 radio frequency (rf) settings operating frequency: 868 mhz max. Operating range: 100 metres (open air) or 30 metres (indoors) environment operating temperature: 0 ºc to + 50 ºc storage temperature: -20 ºc to + 60 ºc receiver instruction manual 24 technical specificati...

  • Page 25: Environment

    Receiver instruction manual 25 technical specification rxwbc605 radio frequency (rf) settings operating frequency: 868 mhz max. Operating range: 100 metres (open air) or 30 metres (indoors) environment operating temperature: 0 ºc to + 50 ºc storage temperature: - 20 ºc to + 60 ºc technical specifica...

  • Page 26: Notes

    Receiver instruction manual 26 notes.

  • Page 27

    Salus controls warrants that this product will be free from any defect in materials or workmanship, and shall perform in accordance with its specification, for a period of two years from the date of purchase. Salus controls sole liability for breach of this warranty will be (at its option) to repair...

  • Page 28: Sales

    Email: sales@salus-tech.Com tel: 01226 323961 email: tech@salus-tech.Com tel: 01226 323961 sales : technical : salus controls plc, salus house, dodworth business park south, whinby road, dodworth, barnsley s75 3sp salus-tech..