1. DL manuals
  2. Samcon
  3. Security Camera
  4. ExCam Series T08
  5. Installation Manual

Samcon ExCam Series T08 Installation Manual

Summary of ExCam Series T08

  • Page 1

    Ex cam ® series t08 - installation manual.

  • Page 2

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 2 of 52 contents 1 introduction .............................................................................................................. 4 2 overview of the device documentation .......................................

  • Page 3

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 3 of 52 list of illustrations figure 10-1 t08-vax.X.X.X mounting options ................................................................... 15 figure 10-4 t08-tnxcd chain link mounting .....................................

  • Page 4

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 4 of 52 1 introduction the excam series (type 08) is an electrical device. It is certified according to atex, iecex and eac-ex as a pressure-resistant camera system to be used in gas and dust explosive areas as well as i...

  • Page 5

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 5 of 52 2 overview of the device documentation t08 excam series (atex/ iecex/ eac-ex) ex installation manual - ec - declaration of conformity - atex type examination - iecex certificate - eac-ex certificate - manufacture...

  • Page 6

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 6 of 52 3 technical data 3.1 parameters of the explosion protection 3.1.1 t08-vax.X.X.X-x-x-x-x identification marks according to directive 94/9/ec: ii 2g (zone 1 and 2) ii 2d (zone 21 and 22) i m2 explosion protection (...

  • Page 7

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 7 of 52 3.1.3 conformity of standards (gas) conformity of standards (gas) iec 60079-0:2011, en 60079-0:2012 iec 60079-1:2008, en 60079-1:2008 iec 60079-11:2011, en 60079-11:2012 iec 60079-18:2009, en 60079-18:2009 iec 60...

  • Page 8

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 8 of 52 3.2 maximum electrical parameters 3.2.1 power supply these are maximum values as part of the approval. Please refer to the device-specific values in the respective user manual! Type t08..: power supply: u in : 12...

  • Page 9

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 9 of 52 3.3 other technical data permitted temperature (storage) 1 : t08-vax.X.X.X -60° c … +85° c (t max ) t08-tnxcd -20° c … +80° c (t max ) /with viton o-ring -30° c … +80° c (t max ) / with nbr 70 o-ring -50° c … +80...

  • Page 10

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 10 of 52 housing material: stainless steel (non-corrosive / en 10027-2) wnr.: 1.4301 (x5crni18-10), aisi 304 wnr.: 1.4305 (x8crnis18-9), aisi 303 wnr.: 1.4401 (x5crnimo17-12-2), aisi 316 wnr.: 1.4404 (x2crnimo17-12-2), a...

  • Page 11

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 11 of 52 4 general safety instructions attention! Cameras of type excam are not suitable for use in zone 0 and zone 20. The temperature class and explosion group as stated on the type plate has to be observed. Alteration...

  • Page 12

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 12 of 52 attention! The instructions stated on the type and instruction plates have to be observed! Camera modules with autofocus: „warning – may not be opened while energized.“ adjustable camera modules or lenses: „warn...

  • Page 13

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 13 of 52 5 application the cameras of the excam ® series are designed and intended for the surveillance of plants as well as of processes at inner as well as outside areas within hazardous areas. The information stated o...

  • Page 14

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 14 of 52 6 transportation and storage - avoid impacts - check the equipment regarding possible damages at the packaging or the camera - store the camera in its original packaging and in a dry and weatherproof place un- t...

  • Page 15

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 15 of 52 7.1.1 type t08-vax.X.X.X for the observation of plants and/or persons, the camera can be installed on a rotatable installation bracket (accessory). The pin which is laterally welded to the housing is in- tended ...

  • Page 16

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 16 of 52 7.1.2 type t08-tnxcd the ptz camera type t08-tnxcd is mounted in a hanging manner (transparent dome copula facing downwards). For installing the dome camera at the wall, the six m8x1.25 threaded holes located at...

  • Page 17

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 17 of 52 7.2 opening and closing of the unit 7.2.1 type t08-vax.X.X.X attention! The pressure tight housing type t08-vax.X.X.X may only be opened when allowed in the user manual of the camera, e.G. For manu- ally adjusti...

  • Page 18

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 18 of 52 the following has to be observed: prior to opening the housing of the type t08-vax.X.X.X it might be necessary to demount the hood or other accessory. - the housing must only be opened on the rear flange of the ...

  • Page 19

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 19 of 52 - pull out very carefully the lead flange in a straight manner (q.V. Figure 10-7) , ensuring that it does not tilt. Due to the created lower pressure, this might require some addi- tional effort the cylindrical ...

  • Page 20

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 20 of 52 attention! In case the flameproof joint has been damaged mechanically, the housing must not be used anymore! Attention! Do not lock-in any foreign objects inside the housing - only the original screws as part of...

  • Page 21

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 21 of 52 7.2.2 type t08-tnxcd attention! The pressure-tight dome housing type t08-tnxcd may only be opened when allowed by the user manual of the camera, e.G. For a manual adjustment, for the removal / exchange of the sd...

  • Page 22

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 22 of 52 - the housing must only be opened at the rear flange of the cable and supply flange. It is not allowed to remove the optic-adapter - in order to open the housing, the body has to be fixed. The cover flange with ...

  • Page 23

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 23 of 52 figure 10-9 opening of the cover flange type t08-tnxcd - the metric fine thread (m188x1.5/ larger 5 supporting thread holes / quality 6g) lo- cated at the flange as well as body component may not be damaged! Dan...

  • Page 24

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 24 of 52 - after completion of the measures, the housing has to be closed again immediate- ly. Do not lock-in any foreign objects! - for closing the housing, please follow, in reversed order, the steps described for the ...

  • Page 25

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 25 of 52 7.3 electrical connection and commissioning attention! The electrical connection of the device may only be carried out by qualified personnel the electrical connection and commissioning must be executed in accor...

  • Page 26

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 26 of 52 8 maintenance/ modification the applicable regulations for the maintenance and servicing of electrical devices in potentially explosive atmospheres must be followed. The necessary maintenance intervals depend on...

  • Page 27

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 27 of 52 11 certificates 11.1 ec – declaration of conformity.

  • Page 28

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 28 of 52 11.2 manufacturer’s declaration concerning the cable and cable entry points.

  • Page 29

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 29 of 52 11.3 ec-type examination certificate.

  • Page 30

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 30 of 52.

  • Page 31

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 31 of 52.

  • Page 32

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 32 of 52.

  • Page 33

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 33 of 52.

  • Page 34

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 34 of 52.

  • Page 35

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 35 of 52.

  • Page 36

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 36 of 52 11.4 iecex certificate of conformity.

  • Page 37

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 37 of 52.

  • Page 38

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 38 of 52.

  • Page 39

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 39 of 52.

  • Page 40

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 40 of 52.

  • Page 41

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 41 of 52.

  • Page 42

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 42 of 52.

  • Page 43

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 43 of 52.

  • Page 44

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 44 of 52 11.5 eac-ex certification.

  • Page 45

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 45 of 52.

  • Page 46

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 46 of 52.

  • Page 47

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 47 of 52.

  • Page 48

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 48 of 52 12 drawings equipment drawings can be found in the individual datasheets. Dxf files, 3d models, drawings of accessories can be found at www.Samcon.Eu for additional information, please contact us at support@samc...

  • Page 49

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 49 of 52 13 notes.

  • Page 50

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 50 of 52.

  • Page 51

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 51 of 52.

  • Page 52

    Doc.-id: 140721-pt08bau-ss-ex installation manual rev.03 (1st supplement), page 52 of 52 schillerstrasse 17, 35102 lohra-altenvers www.Samcon.Eu, info@samcon.Eu fon: +49 6426 9231-0, fax: - 31.