- DL manuals
- Sampo
- TV
- SME-27HD5
- User Manual
Sampo SME-27HD5 User Manual
Summary of SME-27HD5
Page 1
Fcc class b statement -1- 36” (34” viewable ) 16:9 perfectly flat wide screen 34” (32” viewable) 4:3 super flat tube 29” (27” viewable) 4:3 super flat tube high definition digital television user manual.
Page 2: Fcc Class B Statement
Fcc class b statement -1- table of contents 1.Fcc statement.… … … … … … … … … … … … … … … … … ............… … … … … … … 1 2.Important safety instruction… … … … … … … … … … … … … … … … … … 2-5 3.Back panel and connection… … … … ..… … … … … … … … … … … ........… … 6-7 4.Location of buttons on remote c...
Page 3
Fcc class b statement -1- important: the equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of fcc rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment...
Page 4
Ce (europe) statement -2- 1. Bitte lesen sie sich diese hinweise sorgfältig durch. 2. Heben sie diese anleitung für den späteren gebrauch auf. 3. Vor jedem reinigen ist das gerät vom stromnetz zu trennen. Verwenden sie keine flüssig- oder aerosolreiniger. Am besten dient ein angefeuchtetes tuch zur ...
Page 5
Important safety instructions -3- warning: 1. To prevent fire or shock hazard, do not expose this monitor to rain to rain or moisture. 2. High voltage exists on the cathode-ray tube anode lead of this monitor. Before servicing, determine the presence of high voltage by connecting the h.V. Meter betw...
Page 6
Important safety instructions -4- 12. The unit is equipped with a 3-pin grounded plug. The plug will only fit into a grounded power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician. Do not alter the plug; this will defeat the safety fea...
Page 7
Back panel connections -5- • ac in: this terminal is for ac power cord. - rgb in: this terminal is for rgb analog signal, use with ibm pc and other compatibles. ® rgb out: terminal for rgb signal output so that you can attach another display monitor to display the same rgb analog signal that your mo...
Page 8
Back panel connections -6- note: l before connecting any cables, refer to the safety instructions at the beginning of this manual and make sure the unit and the video equipment are both switched off. L be sure to lug the ac power cord to a properly grounded outlet. L the av out terminal only supplie...
Page 9
Remote control functions -7- 5 6 3 4 woofer display recall wide ccd air cable degauss blue back on/off ch add/erase full search 1 7 18 5 10 12 11 2 8 16 14 13 3 20 9 21 15 6 4 17 19.
Page 10
Remote control functions -8- this television features “digital vision”, an advanced on-screen digital display and control system to adjust various settings within the television. These functions are accessible using the remote control for the televison’s front control panels. 1. Pressing the power b...
Page 11
Remote control functions -9- 6. This button is used to add a channel to memory or erase a channel stored in memory. With the channel that you want to add or erase selected and displayed on the screen, press the ch add/erase button. The screen will display “add” or “erase”. If “add” is displayed, it ...
Page 12
Remote control functions -10- 11. Use mts to toggle between sap, mono, or stereo audio mode settings for your television program. Sap, mono, and stereo audio modes are only applicable to standard television broadcasts. 12. Use mute button to quickly turn off the sound through the tv’s internal speak...
Page 13
Remote control functions -11- 17. V-chip v-chip (parental guide) this television is equipped with v-chip technology to prevent children from watching unsuitable programming. To setup v-chip: 1. Press v-chip (blue) key on remote control to enter parental guide setting. Your television will display th...
Page 14
Remote control functions -12- 4. Use s(yellow) or t(green) keys to select the rating you want to set. The selected rating will flash to indicate your selection. Use set (red) key to toggle between the u (unblock) setting or b (block) setting. 5. Press v-chip (blue) key again to access the motion pic...
Page 15
Remote control functions -13- 7. After the above setting is completed, press v-chip (blue) key to set the parental code. 8. Enter a new passcode using the digit keys on the remote control. The pass code must be 5 digits. When you’ve completed entering the 5-digit code, press v-chip (blue) key to com...
Page 16
Remote control functions -14- 18. For sme-34whd5 only when the source of display is av1 or av2 or y/cb/cr, press the wide button to select the display aspect ratio. Each time the wide button is pressed, the on-screen display will toggle between “4:3” and “16:9”. 19. To display the monitor’s on-scree...
Page 17
Battery in remote control -15- open the cover on the back of the remote insert two r06/aa/sum-3 batteries. Be sure the polarity is correct. Replace the cover. Notes : to avoid damage from possible battery leakage, remove the batteries for extended unused periods. Be sure that there are no obstructio...
Page 18
Front panel and connections -16- front view note: l before connecting any cables to the av2 in terminals, make sure the unit and the video equipment are both switched off. Input select degauss － menu ＋ － vol ＋ stand by power saving power l-audio-r video s-video 3adjust4 av2 in input select degauss －...
Page 19
Front panel and connections -17- 1. Pressing the power button turns on the unit. When power is on, the green power led illuminates. When power is off, the unit switches to standby mode illuminating the red standby led. 2. To display the monitor’s on-screen display, press menu +/- button. The first l...
Page 20
On screen display menu settings -18- the tv/monitor function settings are set using the on-screen display. To access function settings, simply press the menu - / + keys on the front control panel or your remote control. Different function settings are available for the different types of signal inpu...
Page 21
On screen display menu settings -19- progressive scan component inputs (y/pb/pr) to change the setting of a particular function, you must first highlight the function by pressing the menu -/+ buttons while the osd is displayed. This will toggle between the displayed functions. After selecting the fu...
Page 22
On screen display menu settings -20- h-width (horizontal size): select icon to adjust the horizontal size of the displayed image. Press the adj- button to decrease h-width. Press the adj + button to increase h-width. This setting is only available to rgb and y/pb/pr input signals. H-phase (horizonta...
Page 23
Power management function -21- the following is a description of the power states and the power consumed in each state: mode led h-sync v-sync video power consumption on green pulse pulse active normal power saving yellow no pulse pulse blanked power saving yellow pulse no pulse blanked power saving...
Page 24
Trouble shooting -22- please refer to the following checklist for remedies to common problems before contacting a service representative. Trouble condition cause remedy no picture 1. Power cord disconnected. 2. Power not switched on. 3. Improperly connected signal cable. 4. Monitor in power save mod...
Page 25
Frequency table -24- band air cb catv ch fp (mhz) assig- nment ch disp fp (mhz) ch disp cb no std brc irc vhf 02 55.25 02 2 55.25 54.00 55.25 low 03 61.25 03 3 61.25 60.00 61.25 04 67.25 04 4 67.25 66.00 67.25 01 4a … … 72.00 73.25 05 77.25 05 5 77.25 78.00 79.25 06 83.25 06 6 83.25 84.00 85.25 95 a...
Page 26
Frequency table -25- band air cb catv ch fp (mhz) assig- nment ch disp fp (mhz) ch disp cb no std brc irc 30 q 259.25 258.00 259.25 31 r 265.25 264.00 265.25 32 s 271.25 270.00 271.25 33 t 277.25 276.00 277.25 34 u 283.25 282.00 283.25 35 v 289.25 288.00 289.25 36 w 295.25 292.00 295.25 37 +1 301.25...
Page 27
Frequency table -26- band air ch catv ch fp (mhz) assig- nment ch disp fp (mhz) ch disp cb no std brc irc 22 519.25 74 v+38 523.25 522.00 523.25 23 525.25 75 v+39 529.25 528.00 529.25 24 531.25 76 v+40 535.25 534.00 535.25 25 537.25 77 v+41 541.25 540.00 541.25 26 543.25 78 v+42 547.25 546.00 547.25...
Page 28
Specifications -27- multimedia monitor 36” (16:9) 34” (4:3) 29” (4:3) 1. Cathode ray tube a. Tube size 36 inch (16:9 aspect ratio) 34 inch (32 inch viewable) 29 inch (27 inch viewable) b. Dot pitch h=0.82mm h=0.8mm h=0.74mm c. Light transmission 76% (typical) 35% typical 49% typical 2. Power a. Inpu...
Page 29
Specifications -28- multimedia monitor 36” (16:9) 34” (4:3) 29” (4:3) 6. Unit dimension: w×h ×d (mm) 1000 × 636 × 695 866 ×718 ×583 742 × 575 ×512 packaging dimension : w×h ×d (mm) 1165 × 870 × 900 1030 × 870 × 760 880 × 647 ×580 7. Net weight of unit : 87 kg 71 kg 51 kg 8. User controls: power, bri...