Wireless microphone system.
Warning to prevent fire or shock hazard. Do not use this plug with an extenon cord, receptacle or other outlet unless the blades can be fully inserted to present blade exposure. To prevent fire or shock hazard. Do not expose this appliance to rain or moisture. To prvent electrical shock, match wide ...
Attention: pour éviter tout risque d’électrocution ou d’incendie, ne pas exposer cet appareil à la pluie ou à l’humidité. Pour éviter tout risque d’électrocution, ne pas ôter le couvercle ou le dos du boîtier. Cet appareil ne con- tient aucune pièce remplaçable par l'utilisateur. Confiez toutes les ...
Precaucion: para reducir el riesgo de incendios o descargas, no permita que este aparato quede expuesto a la lluvia o la humedad. Para reducir el riesgo de descarga eléctrica, nunca quite la tapa ni el chasis. Dentro del aparato no hay piezas susceptibles de ser reparadas por el usuario. Dirija cual...
Copyright 2008-2009, samson technologies corp. V2.1 samson technologies corp. 45 gilpin avenue hauppauge, new york 11788-8816 phone: 1-800-3-samson (1-800-372-6766) fax: 631-784-2201 www.Samsontech.Com.
Table of contents contents introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 quickstart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 guided tour - ar300 receiver / front panel . . . . . . 10-11 guided tour - ar300 receiver / rear panel . . . . . . . . 12 guided...
7 introduction welcome to samson airline synth—the next generation of wireless systems! Wireless microphone and instrument systems were originally developed to eliminate cables, providing unparalleled freedom of movement. Airline synth takes this concept to a new level with transmitters so small, li...
If you’ve had some prior experience using wireless systems, these quickstart instructions will get you up and running with your airline uhf microphone system in a matter of minutes! Detailed instructions for setting up and using your airline synth system can be found on page 15 of this manual, and t...
Quickstart 7. Now to set the channel, press and hold the edit control until the display shows the group number with three asterisks. Next, the ar300 will automatically find the clearest channel and you will see it in the channel number of the display just before the ir set will begin. 8. Once you se...
1. Antennas (a and b) - the antenna mountings allow full rotation for optimum placement. In normal operation, both antenna a (the antenna on the left) and antenna b (the antenna on the right) should be placed in a vertical position. Both antennas can be folded inward for convenience when transportin...
6: edit control – this rotary encoder control knob is used to control and set several menu functions and parameters displayed in the lcd display and it is also used to preform the automatic channel scan. 7: power switch - use this to turn the ar300 power on and off. When the receiver is on, the lcd ...
A: antenna socket - d hole knockout for mounting the antennas to the rear panel using the optional rear antenna kit. B: dc input - connect the supplied power adapter here, using the strain relief as shown in the illustration below. Warning: do not substitute any other kind of power adapter; doing so...
1: plug - insert this standard 3-pin xlr plug into your the included samson q7 or any dynamic microphone. 2: lcd display – this three digit liquid crystal display indicates the absolute channel number that the transmitter is set to. 3: audio on switch – this switch is used to temporarily turn off th...
8: battery compartment - insert a standard aa alkaline battery here, being sure to observe the plus and minus polarity markings shown. We recommend the duracell type battery. Although rechargeable ni-cad batteries can be used, they do not supply adequate current for more than four hours. Warning: do...
The basic procedure for setting up and using your airline synth system takes only a few minutes: 1. Remove all packing materials (save them in case of need for future service) and check to make sure that the supplied power adapter is the correct voltage for your country. If not, contact your distrib...
6. Make the physical cable connection between the ar300 output jack and an audio input of your mixer. Leave your mixer and power amplifier off at this time. 7. Turn the level knob on the ar300 completely counterclockwise, then set its power switch up to turn it on. The lcd display light will illumin...
12. Temporarily turn down the level of your mixer or amplifier and turn off the power to your transmitter, leaving the ar300 receiver on. Then restore the previously set level of your mixer or amplifier. With the transmitter off, the receiver output should be totally silent; if it is, skip ahead to ...
Ar300/ax300 operation setting a group and channel manually the ar300 receiver contains 320 selectable channels for n and u band, and 71 selectable channels for e band. All channels are organized into a series of groups. Each group contains channels that are compatible for simultaneous use. When usin...
Ar300/ax300 operation operating in free mode you can tune in an exact frequency using the ar300’s free mode. Once you are in free mode you can change the frequency by 25 khz steps. For most situations, it’s better to use the group channel plan but if you application requires an exact frequency, foll...
System specifications channels 320 channels 25khz step (n and u bands) 71 channels 25khz step (e band) operating frequency 639.025–647 mhz 798.025–806 mhz (not for use in the usa) 863–865 mhz (not for use in the usa) frequency type f3e modulation type fm noise reduction type compander distance 100 m...
Specifications transmitter (ax300) oscillation type crystal-controlled pll frequency systhesized modulation type fm antenna 1/4 wave length dipole type input impedance 290k ohms(att:0db), 330k ohms(att:-15db) maximum input level -2dbv switches/controls power switch, mute switch, gain control display...
Fcc rules and regulations samson wireless systems are type accepted under fcc rules parts 90, 74 and 15. Licensing of samson equipment is the user’s responsibil- ity and licensability depends on the user’s classification, application and frequency selected. This device complies with rss-210 of indus...
We, samson technologies corporation, located at 45 gilpin ave, hauppauge, ny 11788 usa declare under our own responsibility that the products: are in conformity with the essential requirements of the following ec directive(s) when installed in accordance with the installation instructions contained ...
Samson technologies corp. 45 gilpin avenue hauppauge, new york 11788-8816 phone: 1-800-3-samson (1-800-372-6766) fax: 631-784-2201 www.Samsontech.Com.
