Summary of Expedition EX10
Page 1
® ex10 • ex20 • ex30 owners manual.
Page 2
Produced by on the right wavelength for samson technologies corp. Copyright 2000, samson technologies corp. Printed march 2000 samson technologies corp. 575 underhill blvd. P.O. Box 9031 syosset, ny 11791-9031 phone: 1-800-3-samson (1-800-372-6766) fax: 516-364-3888 table of contents introduction 3 ...
Page 3
Introduction 3 welcome to samson expedition—the portable audio system for the new millenium! This exceptionally versatile system offers the perfect solution wherever you need portable, high-quality audio: as a main pa system or as onstage monitors in clubs and performance halls; in houses of worship...
Page 4
System features the samson expedition system uses state-of-the art technology to bring a revolutionary new degree of flexibility and portability to professional audio. Its main features include: • a built-in telescoping handle and locking wheels that make it easier than ever before to transport your...
Page 5
System features • the ex30 includes all the features of the ex20, and adds a flexible four-channel stereo mixer that provides two monophonic and one stereo mic/line channels with dual xlr and 1/4" connectors. In addition, separate dual phono connectors allow you to hook up an external cassette or cd...
Page 6
Expedition ex10 guided tour 1: 1/4" input - use this standard 1/4" connector to connect signal from a power amplifier (rated at up to 250 watts into 8 ohms) to the ex10. 2: speakon™ input - alternatively, you can use this speakon™ connector to connect signal from a power amplifier (rated at up to 25...
Page 7
Expedition ex10 7 samson mpl2242 mmpl2242 mpl2242 servo - 240 samson samson mpl2242 mmpl2242 mpl2242 servo - 240 samson using two ex10s in mono: a single mono signal (bus or aux send) is routed from a mixer to a power amplifier. One speaker output of the power amplifier is connected to either the ex...
Page 8
8 expedition ex20 guided tour 1: input connector - use this balanced female xlr connector to route line-level signal into the ex20. 2: output vu meter - this three-segment bar meter shows the ex20 output level. For optimum signal-to-noise ratio, set the volume control (see #6 below) so that program ...
Page 9
Expedition ex20 9 ! 0 10 5 ! 0 10 5 samson mpl2242 mmpl2242 mpl2242 ! 0 10 5 ! 0 10 5 samson mpl2242 mmpl2242 mpl2242 using two ex20s in mono: a single mono signal (bus or aux send) is routed from a mixer to one ex20’s xlr input, and a connection is made between that ex20’s xlr output to a second ex...
Page 10
10 expedition ex30 guided tour 1: equalizer - these controls allow you to shape your sound by boosting or cutting the amount of bass (at 100 hz) or treble (at 10 khz) by up to 15 db. A center detent in each knob indicates no boost or cut (that is, flat response). As each knob is turned clockwise fro...
Page 11
11 expedition ex30 5: insert (sub) connector - this 1/4" connector brings line-level signal in directly before the ex30 power amplifiers. It is normally used to return signal from an optional ex500 subwoofer. 6: line inputs - use these 1/4" jacks to connect line-level sources to the ex30. Channels 1...
Page 12
12 expedition ex30 15: cd inputs - connect the outputs of a cd or tape player to this set of dual phono jacks. Signal arriving here returns to stereo channel 3/4. If an optional td30 cassette player is installed, note that its output also arrives at channels 3/4, in addition to line-level signal arr...
Page 13
Expedition ex30 13 using one ex30 and an ex20 (stereo operation): in this example, microphones are connected to the xlr mic inputs of channels 1 and 2 of an ex30, and a stereo keyboard is connected to the stereo 1/4" trs connector of channel 3/4 of the ex30 (using a y-cord, with the tip carrying the...
Page 14
14 positioning and mounting instructions general positioning tips • operating a microphone or turntable in front of a speaker is a sure formula for feedback and/or rumble problems, so always place the expedition in front of any mics or turntables that are being used. • use the expedition upright for...
Page 15
15 positioning and mounting instructions before fly-mounting, wall-mounting or ceiling-mounting the expedition, you must first install a samson mp 1030 mounting bracket to the fly points, as shown in the illustrations on the right standard cabling and hardware can then be attached to the mp 1030 mou...
Page 16
16 as shown in the illustration on the left, the top panel of the expedition ex20 and ex30 provides a prewired compartment that accommodates any of three different samson wireless receivers: the um1 or m32 uhf models or the vm1 vhf model. Output signal from a wireless receiver mounted in an ex30 arr...
Page 17
17 specifications power rating: (@ 8 Ω ): ex10 250 watts program; 400 watts max. Peak ex20, ex30 160 watts lf; 40 watts hf frequency response: (all models) 60 hz – 15 khz ± 3 db sensitivity: ex10 97 db spl @ 1w/1m crossover frequency: ex10 2.3 khz (12 db per octave) ex20, ex30 2.3 khz (24 db per oct...