Summary of SD8
Page 1
® owners manual p o w e r e d mixer s d 8.
Page 2
Produced by on the right wavelength for samson technologies corp. Copyright 1997, samson technologies corp. Printed march 1997 samson technologies corp. 575 underhill blvd. P.O. Box 9031 syosset, ny 11791-9031 phone: 1-800-3-samson (1-800-372-6766) fax: 516-364-3888.
Page 3
Introduction 1 sd8 features 2 guided tour 4 overview 4 channel 5 main section 7 rear panel 9 connecting the sd8 - general suggestions 11 setting up and using the sd8 12 setting the correct gain structure 13 suggested performance application 15 grounding techniques 16 using equalization 17 using the ...
Page 4
Introduction congratulations—you’ve made an excellent choice in your purchase of the samson sd8 stereo mixer amplifier! In this manual, we’ll take you on a guided tour through all the features of this powerful and flexible device, and we’ll tell you how to get the most out of the sd8. Although desig...
Page 5
Sd8 features the samson sd8 utilizes state-of-the-art technology in integrated mixer/amplifier design. Here are some of its main features: • convenient carrying handle and supplied standard 19" rack ears (the sd8 takes just four rack spaces) allows easy integration into any setup. • eight independen...
Page 6
Sd8 features • protection relay circuitry prevents “thumps” when powering on or off. This means that you can use the sd8 with a single power strip into which other audio devices are connected, without danger of damage to connected speakers. • a rear-panel amplifier input allows you to bring external...
Page 7
Guided tour - overview the following illustration shows an overview of the front panel of the sd8: 4 8 channel stereo mixer 250 watt amplifier -15 -9 -6 -3 0 +3 +6 phantom power return 1-2 main level effect headphones preset monitor protect aux1/mon -15 -9 -6 -3 0 +3 +6 l r 32hz 64hz 125hz 250hz 500...
Page 8
Guided tour - channel 1: level (white) - this knob determines the final signal level being sent by a channel to the main speaker outputs. In practice, this will be used to adjust the levels of the various signals being blended together by the sd8. The “0” position indicates unity gain (no level atte...
Page 9
Guided tour - channel 6: equalizer (blue) - these knobs determine the amount of boost or attenuation in each of three frequency areas. The high and low frequency knobs provide 15 db of cut or boost at 10 khz and 80 hz, respectively, with shelving-type control. The mid frequency knob provides 12 db o...
Page 10
7 guided tour - main section 1: meter - this seven-segment bar meter shows the continuous output level of the sd8. For optimum signal-to-noise ratio, try to adjust all levels (channel and main) so that program material is usually at or around 0 vu, with occasional but not steady excursions to the +3...
Page 11
8 guided tour - main section 4: main level (white) - this knob determines the final signal level sent to the speaker output jacks on the rear panel. You can think of this as being the “master fader”—and we made this knob extra big so you won’t miss it even under low-light performance conditions. At ...
Page 12
Guided tour - rear panel 1: power switch - as you may have guessed, this is what you use to turn the sd8 on and off. The built-in protection relay circuitry (which mutes the outputs for approximately five seconds after powering on) prevents power-on “thumping,” which can potentially damage connected...
Page 13
10 guided tour - rear panel 5: aux sends 1 - 2 - these unbalanced outputs allow you to route signal from each of the two discrete effects sends to external devices such as effects processors. Aux send 1 is pre-fade and pre-eq, while aux send 2 is post-fade and post-eq. See the “using the aux sends a...
Page 14
11 the actual connections you’ll make to and from the sd8 will vary according to the environment you use it in and the particular equipment you have. However, here are a few basic rules concerning connections that will apply in pretty much all situations: • in general, it’s best to make all connecti...
Page 15
12 setting up your sd8 is a simple procedure which takes only a few minutes: 1. Remove all packing materials (save them in case of need for future service) and decide where the sd8 is to be physically placed—if desired, remove the carrying handle and install the supplied rack ears so that it can be ...
Page 16
13 you’re now ready to establish the correct gain structure—the key to getting the best performance from the sd8, or from any mixer, for that matter. This is a simple procedure that ensures optimum input and output levels so that no unnecessary noise (caused by too low a signal) or overload distorti...
Page 17
14 j. The procedure for setting optimum microphone levels is virtually identical; sing or speak into the mic at the level you expect to use in performance while slowly raising the level control for that channel to its “0” position. Then adjust the input trim control for that channel while watching t...
Page 18
15 suggested performance application the following illustration shows the basic interconnections between an sd8 and external equipment when used in a typical live performance application: the main connections here involve connecting the sd8 speaker outputs to pa speakers and the monitor output to th...
Page 19
16 grounding techniques hum and buzz are the biggest enemies you face when interconnecting a large number of different pieces of equipment to a central audio mixer. This is because each piece of equipment may operate at a marginally different voltage (this difference is called potential) and, when t...
Page 20
17 using equalization one of the most exciting aspects to using a mixer such as the sd8 is having the ability to shape a sound, using a process called equalization. But there are few areas of audio engineering more misunderstood than equalization, and, just as good eq can really help a sound, bad eq...
Page 21
18 using equalization in most instances, the best way to approach equalization is to think in terms of which frequency areas you need to attenuate, as opposed to which ones you need to boost. (boosting a frequency area also has the effect of boosting the overall signal; too much eq boost can actuall...
Page 22
19 using the aux sends and returns and monitor output the two aux sends provided by the sd8 allow you to combine the signal from multiple channels and send the resulting mix to the rear panel monitor output jack, to the internal zoom digital signal processor (dsp), or to external devices such as eff...
Page 23
20 using the internal digital signal processor (dsp) there’s probably no better way to enhance audio than with the judicious use of effects such as reverb and echo. The sd8 has its own built-in digital signal processor (dsp) chip which provides some of the best effects around. These are some of the ...
Page 24
Table of sd8 effects preset # description effect settings 1 hall reverb - simulates a alter the reverb time. Effect 1 (standard) is 2.2 seconds. Medium-sized concert hall larger effect values increase the reverb time, from 1.0 second (effect 2) to 3.8 seconds (effect 16). 2 room reverb - simulates a...
Page 25
22 specifications mixer / pre amp section: normal limit frequency response (± 3 db) mic to pre out dc ~ 65 khz 20 hz - 50 khz line to pre out dc ~ 58 khz 20 hz - 50 khz aux return to pre out dc ~ 70 khz 20 hz - 50 khz total harmonic distortion (20 hz to 20 khz, with 30 khz lpf, trim center) mic to p...
Page 26
23 specifications power amp section: normal limit rated output power (per channel) (1% thd @ 1 khz stereo, 4 ohm) 275 watt 250 watt min maximum voltage gain amp in to speaker out (@ 1 khz) 27.5 db 28 db ± total harmonic distortion (20 hz to 20 khz with 30 khz lpf) 0.02% 0.1% max frequency response (...