1. DL manuals
  2. Samsung
  3. Air Conditioner
  4. AC***FB4DEH
  5. Installation Manual

Samsung AC***FB4DEH Installation Manual

Summary of AC***FB4DEH

  • Page 1

    Cassette type series acfb4deh acfb4peh acfb4feh ns4pxea ns4dxea ns4zxea air conditioner installation manual imagine the possibilities thank you for purchasing this samsung product. Db98-32787a-15 it fr es en pt el de cac cassette type 유럽-터키향_im_32787a-14_en.Indd 29 2016-05-26 오후 5:...

  • Page 2: Contents

    2 preparation for installation ............................................................................................................................................................................................... 3 deciding on where to install the indoor unit .................................

  • Page 3: Preparation For Installation

    3 english when deciding on the location of the air conditioner with the owner, the following restrictions must be taken into account. Our units should be installed in compliance with the spaces shown in the installation manual, to ensure accessibility from both sides and allow repairs or maintenance...

  • Page 4: Preparation For Installation

    4 deciding on where to install the indoor unit preparation for installation the following accessories are supplied with the indoor unit. The type and quantity may differ depending on the specifications. Indoor unit space requirements for indoor unit accessories there must be no obstacles near the ai...

  • Page 5

    5 english • the units must be installed according to distances declared, in order to permit accessibility from each side, either to guarantee correct operation of maintenance or repairing products. The unit’s parts must be reachable and removable completely under safety condition (for people or thin...

  • Page 6

    6 deciding on where to install the indoor unit model 052fb4d 071fb4d 0714dx 071fb4p 090fb4d 100fb4d 0714px 0904dx 1004dx 090fb4p 0904px 1254dx 100fb4p 100fb4f 1004px 1004zx 1254px 1404px 1404dx c mm 251 293 335 335 net dimension mm 840×204×840 840×246×840 840×28...

  • Page 7

    7 english a b unit : mm model 052fb4d 071fb4d 0714dx 071fb4p 0714px 090fb4d 100fb4d 0904dx 1004dx 090fb4p 0904px 1254dx 100fb4p 100fb4f 1004px 1004zx 1254px 1404dx 1404px a mm 204 246 288 b mm 253 295 337 net dimension mm 840 x 204 x 840 840 x 246 x 840 840 x 28...

  • Page 8: Indoor Unit Installation

    8 indoor unit installation ceiling support pad stopper bracket ceiling 17mm 20mm indoor unit gauge of dimensions concrete suspension bolt(m8)-field supply hole in anchor hole in plug insert when deciding on the location of the air conditioner with the owner, the following restrictions must be taken ...

  • Page 9: Purging The Unit

    9 english there are two refrigerant pipes of different diameters : a smaller one for the liquid refrigerant a larger one for the gas refrigerant the inside of copper pipe must be clean & has no dust 1. Remove the pinch pipe on the pipes and connect the assembly pipes to each pipe, tightening the nut...

  • Page 10: Cutting/flaring The Pipes

    10 cutting/flaring the pipes 1. Make sure that you have the required tools available. (pipe cutter, reamer, flaring tool and pipe holder) 2. If you wish to shorten the pipes, cut it with a pipe cutter, taking care to ensure that the cut edge remains at a 90° angle with the side of the pipe. Refer to...

  • Page 11

    11 english to identify potential gas leaks on the indoor unit, inspect the connection area of each refrigerant pipe using a leak detector for r410a. Before recreating the vacuum and recirculating the refrigerant gas, it is advisable to pressurize the whole system with nitrogen (using a cylinder with...

  • Page 12

    12 drainpipe and drain hose installation 1 push the supplied drain hose as far as possible over the drain socket. 2 tighten the metal clamp as shown in the picture. 3 wrap the supplied large sealing pad over the metal clamp and drain hose to insulate and fix it with clamps. 4 insulate the complete d...

  • Page 13

    13 english • if a concentrated drain pipe is installed, refer to the figure below. Concentrated drain pipe 100mm or mor e 1/100 or mor e slope air ventilation check that the indoor unit is level with the ceiling by using the leveler. Air ventilation ceiling install air ventilation to drain condensat...

  • Page 14: Memo

    14 memo drainpipe and drain hose installation 1. Check the leak test at the connection part of the flexible hose and the distributing pipe (pvc). 1) connect a general hose to the connection part of the flexible hose of the indoor unit, and pour in some water. 2) after pouring some water, reassemble ...

  • Page 15

    15 english connecting the connection cord • always remember to connect the refrigerant pipes before performing the electric connections. When disconnecting the system, always disconnect the electric cables before disconnecting the refrigerant pipes. • always remember to connect the air conditioner t...

  • Page 16: Installation Procedure

    16 how to connect your extended power cables 1. Prepare the following tools. Tools crimping pliers connection sleeve (mm) insulation tape contraction tube (mm) spec mh-14 20xØ6.5(hxod) width 19mm 70xØ8.0(lxod) shape 2. As shown in the figure, peel off the shields from the rubber and wire of the powe...

  • Page 17

    17 english 5. Wrap it with the insulation tape twice or more and position your contraction tube in the middle of the insula- tion tape. A total of three or more layers of insulation is required. F method 1 40 mm insulation tape f method 2 insulation tape 35 mm 6. Apply heat to the contraction tube t...

  • Page 18

    Aa 18 step 1. Entering mode to set option 1. Remove batteries from the remote controller. 2. Insert batteries and enter the option setting mode while pressing high temp button and low temp button. 3. Check if you have entered the option setting status. Step 2. The procedure of option setting after e...

  • Page 19

    19 english option setting statusv 1. Setting seg2, seg3 option press low fan button( ∨ ) to enter seg2 value. Press high fan button( ∧ ) to enter seg3 value. Each time you press the button,   …  will be selected in rotation. 2. Setting cool mode press mode button to be changed to cool mode in the...

  • Page 20

    20 setting an indoor unit address and installation option option setting status 12. Setting cool mode press mode button to be change to cool mode in the off status. 13. Setting seg16, seg17 option press low fan button( ∨ ) to enter seg16 value. Press high fan button( ∧ ) to enter seg17 value. Each t...

  • Page 21

    21 english 1. Check whether power is supplied or not. - when the indoor unit is not plugged in, there should be additional power supply in the indoor unit. 2. The panel(display ) should be connected to an indoor unit to receive option. 3. Before installing the indoor unit, assign an address to the i...

  • Page 22

    Aa 22 setting an indoor unit address and installation option 1. Check whether power is supplied or not. - when the indoor unit is not plugged in, there should be additional power supply in the indoor unit. 2. The panel(display ) should be connected to an indoor unit to receive option. 3. Set the ins...

  • Page 23

    23 english option seg1 seg2 seg3 seg4 seg5 seg6 explanation page mode reserved use of external temperature sensor use of central control reserved remote controller display indication and details indication details indication details indication details indication details 0 2 0 disuse 0 disuse 1 use 1...

  • Page 24: Memo

    24 memo setting an indoor unit address and installation option you can change each digit of set option. Changing a particular option option seg1 seg2 seg3 seg4 seg5 seg6 explanation page mode the option mode you want to change the tens’ digit of an option seg you will change the unit digit of an opt...

  • Page 25: Troubleshooting

    25 english troubleshooting abnormal conditions led lamp display remarks operation defrost timer filter reset power reset x x x error of temperature sensor in the indoor unit (open/short) x x x error of heat exchanger sensor in the indoor unit (open/short) x x error of fan motor in the indoor unit x ...

  • Page 26: Memo

    26 memo cac cassette type 유럽-터키향_im_32787a-14_en.Indd 26 2016-05-26 오후 5:19:07.

  • Page 27: Memo

    27 memo english cac cassette type 유럽-터키향_im_32787a-14_en.Indd 27 2016-05-26 오후 5:19:08.

  • Page 28

    Samsung electronics co., ltd. Sgec : 107, hanamsandan 6beon-ro, gwangsan-gu, gwangju-si, korea 62218 samsung electronics (uk) ltd, euro qa lab. Blackbushe business park. Saxony way, yateley, hampshire. Gu46 6gg united kingdom "aeee yönetmeligine uygundur" this product is rohs compliant cac cassette ...