1. DL manuals
  2. Sentry
  3. Car Seat
  4. The Guardimals
  5. Owner's Manual

Sentry The Guardimals Owner's Manual

Summary of The Guardimals

  • Page 1

    Owner's manual www.Sentrybabyproducts.Com customer service: 01-719-212-6016 carefully read and understand all instructions and warnings in this manual. Failure to properly use this car seat increases the risk of serious injury or death in a sudden stop or crash. Keep instructions for future use. War...

  • Page 2

    1.0 general warnings and information........................................... 5 2.0 warnings............................................................................. 7 3.0 features and benefits 3.1 toddler car seat......................................................................... 11 3.2 ...

  • Page 3

    7.3 installation top tether...................................................... 28 with 7.3.1 installation - latch top tether............................... 29 with 7.3.2 installation - lap/shoulder belt top tether............... 34 with 7.3.3 installation - lap belt only with top tether.............

  • Page 4

    5 proper use is required! Even if using this car seat seems easy to figure out, it is very important to follow the car seat and vehicle owner’s manuals! • failure to follow these instructions and car seat labels can result in a child striking the vehicle’s interior during a sudden stop or crash. - yo...

  • Page 5

    6 possible. - car seat must stay tightly secured in vehicle. B. Booster use mode - requires proper routing and adjusting fit of vehicle lap/shoulder belt. C. Always properly position the vehicle belts on your child and snugly adjust the vehicle belts around child. Note: not all vehicle seat belts or ...

  • Page 6

    7 in child striking the vehicle’s interior during a sudden stop or crash. • use this car seat only with children who weigh between 22 and 100 lbs. (10 and 45 kg.) and whose height is between 29 and 57 in. (74 and 145 cm) and who are capable of sitting upright unassisted. • child must be at least 1 y...

  • Page 7

    • stage 1 toddler use mode: - secure this car seat with the vehicle’s child restraint anchor- age system (latch) if available or with a vehicle belt. - secure top tether provided with this child restraint. - always use proper belt routing based on tether use. - snugly adjust harness around child. - ...

  • Page 8

    9 • this car seat is designed and tested to accommodate a child of a specific range of weight and height. Using the car seat for a child whose weight or height is outside of these limits will increase the risk of death or serious injury in the event of a crash (see section 5.0 of this manual for weig...

  • Page 9

    10 • the car seat may become very hot if left in direct sunlight. Your child may suffer burns from hot components. Always check the car seat for hot surfaces that may come into contact with your child before placing your child in the car seat. We suggest that you cover the car seat with a blanket or ...

  • Page 10

    3.1 toddler car seat ( with built-in harness system) head support back support covers cover cover cover cover shoulder strap harness clip harness straps harness adjuster strap cup holder feet paw harness buckle buckle tongues crotch strap seat base 11 3.0 features and benefits.

  • Page 11

    ( with built-in harness system) 3.2 toddler car seat belt path height-adjust headrest push button shoulder belt guides belt path opening opening harness strap slots latch lower anchor belt anchor adjuster anchor storage anchor hook top tether strap top tether top tether adjuster hook latch lower har...

  • Page 12

    13 the steps to prepare the car seat for use with your child are outlined below and described in detail in this owner’s manual. 4.1 assemble the back support (see “assembly and removal of back support” section) before using your car seat in your vehicle, you must assemble the back support to the sea...

  • Page 13

    14 backless booster car seat harness system without “40 - 100 lbs.” (18 to 45 kg) (see weight and height recommendations” section). - remove back support (see “assembly and removal of back support” section). 4.3 select a vehicle seating location to install the car seat • select a vehicle seating loc...

  • Page 14

    15 4.4 proper use check list √ car seat is securely installed in vehicle. √ the correct belt routing for installation is used based on use of tether. √ top tether is used, when possible. √ harness straps are in harness slots at or above child’s shoulders. √ harness is snugly adjusted around child. B...

  • Page 15

    16 warning! Death or serious injury can occur: • failure to use child restraint in a manner ap propriate for your child’s size may increase th e risk of serious injury or death. 5.1 car seat use modes ranges listed below and depends on the size of your child. Instructions for the proper use of this ...

  • Page 16

    17 5.2 toddler car seat use ( with built-in harness system) child must meet all of the following requirements to use the toddler car seat mode: • child must be at least 1 year old and able to sit upright unassisted and • weigh t between 22 and 50 lbs. (10 and 23 kg) and • child’s height is between 2...

  • Page 17

    18 5.3 h igh-back booster car seat use ( without built-in harness system) child must meet all of the following requirements to use the high-back booster car seat mode: • child’s weight is between 30 and 100 lbs. (14 and 45 kg) and • child’s height is between 38 and 5 7 in. (96 and 1 45 cm) and • chi...

  • Page 18

    19 5.4 backless booster car seat use ( without built-in harness system) child must meet all of the following requirements to use the backless booster car seat mode: • child’s weight is between 40 and 100 lbs. (18 and 45 kg) and • child’s height is between 42 and 57 in. (107 and 145 cm) and • top of ...

  • Page 19

    20 warning! • there are many different types of vehicles, vehicle seat belt sy stems, or other occupant restraint systems in use today. Ac cordingly, this manual can only give guidelines for proper in stallation in your vehicle. In addition to this manual, you m ust also read and understand the vehic...

  • Page 20

    21 61 overall considerations for selecting a . Seating location • please review your vehicle owner’s manual to determine the best location for each car seat use mode, any specific instructions for car seat installation, or to determine if any locations are unsafe for car seat installation. If you do ...

  • Page 21

    Latch lower anchors and tethers for children ( latch) system is designed to make installation of child car seats easier by requiring child restraints to be installed without using the vehicle’s seat belt system. Since september 1, 2002, at least two rear seating positions of all cars, mini vans and ...

  • Page 22

    6.2 seating locations to avoid do not use this car seat in the following seating locations. • never use this car seat in a vehicle seating location that has an active frontal air bag unless recommended in the vehicle owner’s manual. If your vehicle is equipped with a front passenger air bag, please ...

  • Page 23

    24 7.1 proper installation warning! • proper installation is required. Th e belt routing for securing th is car seat in a vehicle is de pendent on installation with or without the top tether. • secure this child restraint with la tch system or vehicle seat be lt and top tether strap as sh own in thi...

  • Page 24

    25 the belt path routing used to secure this car seat into a vehicle is dependent on installation or with without the top tether. - if the car seat is installed the top tether, the “front with entry” belt routing must be used. Rear entry” belt routing must be used. - if the car seat is installed the...

  • Page 25

    26 7.2 belt routing options for installation: “front entry” belt routing the "front entry" belt routing is used to secure the toddler car seat ( harness) when installed with with the top tether. The latch lower anchor belt and vehicle seat belts are routed through the “front entry” belt path in the ...

  • Page 26

    Installation top tether without “rear entry” belt routing (with harness) when installed the top tether. The latch without lower anchor belt and vehicle seat belts are routed through the “ rear entry” belt path in the same way. “rear entry” belt routing • from the rear of the car seat, insert the lat...

  • Page 27

    7.3 installation top tether with be used when the top tether is used to the “front entry” belt routing, must secure this car seat. Based on the seating location selected, identify if latch, vehicle lap/shoulder or vehicle lap belt only will be used to secure the car seat. Use the latch system when a...

  • Page 28

    29 7.3.1 installation - latch top tether with warning! • only use the car seat latch system in vehicle seating po sitions designated by the vehicle manufacturer as latch us e position and have anchor spacing of 11 inches (280 mm). • the car seat must be held tightly by the latch system. • never atta...

  • Page 29

    3. Route the latch lower anchor belt using the “front entry” belt routing as shown in section 7.2. 4. Place top tether strap over the top of the head support and rest inside seating area. 5. Place the car seat on the vehicle seat in a seating location equipped with latch and centered between the lat...

  • Page 30

    9. Place knee inside seat and while pressing down, pull on the free end of the latch lower anchor belt to tighten the latch lower anchor belt around the car seat . 10. Attach top tether hook to vehicle tether anchor and . Listen for the “click” when the tether hook locks onto the vehicle tether anch...

  • Page 31

    32 13. Check for a secure installation by grasping the car seat armrest and pushing side-to-side and front-to-back. The car seat should not move more than 1 inch in either direction. • if the car seat moves more than 1 inch, retighten the latch belt and top tether and test again. • if the car seat m...

  • Page 32

    To remove car seat: 1. Loosen top tether by pressing the button on tether adjuster and sliding belt through adjuster . 2. Unhook top tether hook from vehicle tether anchor. Press up on retainer , unhook tether hook , and remove . 3. Loosen latch lower anchor belt by putting knee in seat and while pr...

  • Page 33

    To secure car seat in vehicle: and removal of back support” section). 2. Store latch connectors in pouch on back 1. Assemble the back support (see “assembly of seat. 3. Adjust the harness strap height for your child – harness straps must be at or above the child’s shoulders (see “changing harness st...

  • Page 34

    35 6. If the vehicle seat back is adjustable, adjust into the upright position or the position specified in the vehicle o wner’s manual for use with a car seat. 7. Pull the vehicle lap/shoulder belt out and route through the car seat using the "front entry" belt routing as shown in section 7.2 and bu...

  • Page 35

    12. While holding the lap belt tight, pull slack out of shoulder belt and allow retractor to tighten sh oulder belt. 13. Attach top tether hook to vehicle tether th e tether hook locks onto the vehicle tether anchor. 14. Pull on the top tether strap to check that 15. Pull on free end of top tether s...

  • Page 36

    1. Loosen top tether by pressing the button on the tether adjuster and sliding belt through adjuster . 2. Unhook top tether hook from vehicle tether anchor. Press up on retainer , unhook tether hook , and remove . 3. Unbuckle vehicle seat belt and remove seat belt from belt path. 37 7.3.3 installati...

  • Page 37

    To secure car seat in vehicle: 1. Assemble the back supposrt (see "assemble and removal of back support” section). 2. Store latch hooks in pouch on back of seat. 3. Adjust the harness strap height for your child – harness straps must be at or above the child’s shoulders (see “changing harness strap ...

  • Page 38

    2 1 7. Pull the vehicle lap belt out and route through the car seat using the “ front entry” belt routing as shown in section 7.2 and buckle the vehicle seat belt. 8. Pull to check that the vehicle buckle is securely locked. Note: if lap belt is not long enough and latch system is not available, ins...

  • Page 39

    40 13. Check for a secure installation by grasping the car seat armrest and pushing side-to-side and front-to-back. The car seat should not move more than 1 inch in either direction. • if the car seat moves more than 1 inch, retighten the vehicle seat belt and top tether and test again. • if the car...

  • Page 40

    The “rear entry” belt routing must be used when a top tether is not used to secure this car seat. Note: installation with top tether is recommended whenever possible. Sentry baby requires using the top tether provided with this car seat whenever possible. However when a tether anchor is not availabl...

  • Page 41

    42 7.4.1 installation - latch top tether without warning! • only use the car seat latch system in vehicle seating po sitions designated by the vehicle manufacturer for use w ith latch and have anchor spacing of 11 inches (280 mm). • the car seat must be held tightly by the latch system. • never atta...

  • Page 42

    43 3. Adjust the harness strap height for your child – harness straps must be at or above the child’s shoulders (see “changing harness strap height” section). 4. Route the latch lower anchor belt using the “rear entry” belt routing as shown in section 7.2. 5. Place the car seat on the vehicle seat i...

  • Page 43

    1 2 9. Place knee inside seat and while pressing down, pull on the free end of the latch lower anchor belt to tighten the latch lower anchor belt around the car seat . 10. Check for a secure installation by grasping the car seat armrest and pushing side-to-side and front-to-back. The car seat should...

  • Page 44

    2 1 to remove car seat: 1 . Loosen latch lower anchor belt by putting knee in seat and while pressing down , lift up on latch adjuster and slide belt through adjuster . 2. Unhook latch lower anchor belt hooks from vehicle anchors. Press up on retainer , unhook latch hooks , and remove . Note: when r...

  • Page 45

    To secure car seat in vehicle: “assembly and removal of back support” section). 2. Store latch and top tether by 1. Assembly the back support (see securing latch connectors and tether hook on latch/tether storage at bottom of back support as shown. 3. Adjust the harness strap height for your child –...

  • Page 46

    4. Place the car seat on the vehicle seat in a seating location and centered between the lap/shoulder belt anchorages (see “selecting a vehicle seating location” section). 5. If the vehicle seat back is adjustable, adjust into the upright position or the position specified in the vehicle owner’s manu...

  • Page 47

    48 10. While holding the lap belt tight, pull slack out of shoulder belt and allow retractor to tighten shoulder belt. 11. Check for a secure installation by grasping the car seat armrest and pushing side-to-side and front-to-back. The car seat should not move more than 1 inch in either direction. •...

  • Page 48

    49 to secure car seat in vehicle: “assembly and removal of back support” section). 2. Store latch and top tether by 1. Assemble the back support (see securing latch connectors and tether hook on latch/tether storage bar at bottom of back support as shown. 3. Adjust the harness strap height for your ...

  • Page 49

    50 a seating location and centered between the lap belt anchorages (see “selecting a vehicle seating location” section). 5. If the vehicle seat back is adjustable, adjust 5. Place the car seat on the vehicle seat in into the upright position or the position specified in the vehicle owner’s manual for...

  • Page 50

    51 9. 1. To remove car seat: check for a secure installation by grasping the car seat armrest and pushing side-to-side and front-to-back. The car seat should not move more than 1 inch in either direction. • if the car seat moves more than 1 inch, retighten the latch belt and test again. • if the car...

  • Page 51

    52 7.5 securing your child minimum use recommendations sit upright unassisted and weigh at least child must be at least 1 year old, able to 22 lbs. (10 kg) to use this car seat. 7.0 toddler car seat ( with built-in harness) installation and use.

  • Page 52

    53 warning! Death or serious injury can occur: • failure to properly adjust the harness on your child in creases the risk of death or serious injury in the event of a sudden stop or crash. Follow the instructions very closely to ensure that the harness is properly adjusted to fit your ch ild at all t...

  • Page 53

    To secure your child: 1. Check that harness straps are through harness slots at or just above child’s shoulders. 2. Place child in car seat with child’s back contacting back support and rump contacting seating surface. 3. Buckle harness. - place harness straps over child’s shoulders and thighs. - in...

  • Page 54

    55 4. Snugly adjust harness around your child by pulling the harness adjuster strap at front of car seat shown. See “adjustment of the harness straps” section for more information on tightening and loosening the harness. 7.0 toddler car seat ( with built-in harness) installation and use.

  • Page 55

    56 5. Close harness clip and position as close to arm pit level as possible. 6. Check that the harness straps are snugly adjusted. - check that harness straps are snug on child’s shoulders and thighs. - the harness strap is properly tightened if you are not able to insert more than one finger between...

  • Page 56

    1 1 2 2 57 to remove your child: tabs in the top and bottom of the harness clip and pull apart to open the harness clip. 2. Unbuckle the harness buckle to 1. Unbuckle harness clip - press on the open the harness system 3. Slide the harness straps off the child’s shoulders and arms. 4. Remove your chi...

  • Page 57

    58 warning! Death or serious injury can occur: • child must be at least 3 years old and w eigh at least 30 lbs. (14 kg) to use th e booster mode. • use only the vehicle’s lap/shoulder belt sy stem when restraining the child in this bo oster car seat. • never use the booster car seat with on ly a veh...

  • Page 58

    59 death or serious injury can occur: • if child will not keep vehicle shoulder belt properly positioned on shoulder, do not use this booster car seat. Use a di fferent child restraint system. • do not allow child to slide down in high-back booster car se at which could position vehicle lap belt acro...

  • Page 59

    60 note: latch or top tether may be used to secure the high-back booster car seat in position. Securing the high-back booster car seat in the vehicle can make it easier for a child to get in and out of the high-back booster car seat (see, section 7.3.1). Support” section). To secure car seat and you...

  • Page 60

    5. If the vehicle seat back is adjustable, adjust into the upright position or the position specified in the vehicle owner’s manual for use with a car seat. 6. Thread shoulder belt into the in ner slot of booster shoulder b elt guide located on the u nderside of the head support. - slide shoulder bel...

  • Page 61

    62 9. Adjust head support so that the vehicle s houlder belt passes over the shoulder m idway between the neck and the end o f the shoulder. The booster shoulder b elt guide in the head support should b e just above the child’s shoulders. 10. Snugly adjust the vehicle lap/shoulder b elt according to...

  • Page 62

    63 11. Check fit of the vehicle seat belts on child: - vehicle lap belt must be low on hips contacting the thighs. - vehicle shoulder belt must contact the chest and be centered o n the shoulder. Adjust head support to position the vehicle s h oulder belt. - do not place vehicle shoulder belt u n der...

  • Page 63

    Death or serious injury can occur: or • child must be at least 4 years old and weigh at least 40 lbs. (18 kg) to use the backless booster car seat. • use high-back booster mode as long as possible. The back support and head support provide incremental crash protection in frontal and side impact cras...

  • Page 64

    65 2. Tuck harness adjustment belt up under front of the seat base. 3. Assemble vehicle shoulder belt positioner to back of car seat (see “assembly and removal of vehicle shoulder belt positioner” section). 4. Place the car seat on the vehicle seat in a location equipped with a lap/shoulder belt and...

  • Page 65

    7. Pull the vehicle lap/shoulder belt across front o f child and buckle vehicle seat belt. - v ehicle shoulder belt on buckle side must be under armrest. 8. Place vehicle shoulder belt in vehicle shoulder belt positioner and adjust to position shoulder belt on child. - t hread harness strap through ...

  • Page 66

    67 9. C heck fit of the vehicle seat belts on child: - vehicle lap belt must be low on hops contacting the thighs. - vehicle shoulder belt must contact the c h est and be centered on the shoulder. U se the shoulder belt positioner to adjust th e position of the vehicle shoulder belt. - do not place v...

  • Page 67

    68 9.1 check that the vehicle seat belt is safe to use belt must be capable of maintaining tight installation at all times. The car seat must be tightly secured at all times. The vehicle seat a variety of vehicles have been equipped with vehicle seat belt sys - tems that are not safe for use with th...

  • Page 68

    Safe seat belt systems: the following vehicle seat belt systems can be used with the car seat provided that all of the other requirements prescribed in these instructions, including seat position, and all instructions provided by your vehicle’s owner’s manual are followed. For both toddler use or bo...

  • Page 69

    70 combination lap/shoulder belt with sliding latch plate please refer to your vehicle owner’s manual for additional information on locking this style of seat belt. This style of belt must be locked to prevent movement of car seat. For toddler use mode harness: with lap belts (manually adjusted) • a...

  • Page 70

    71 unsafe seat belt systems: do not use the following types of vehicle seat belt systems with the car seat. These vehicle seat belt systems will not hold the car seat securely in place at all times. The addition of a locking clip will not make these vehicle seat belt systems safe to use. Note: latch...

  • Page 71

    72 combination lap/shoulder belt with retractor: do not use a vehicle lap/shoulder belt system if the lap belt and shoulder belt each have retractors at one end. This type of vehicle seat belt system will not adequately restrain the car seat. Passive restraint - lap or shoulder belt mounted on door:...

  • Page 72

    73 lap belts located forward of seat crease: do not use a vehicle seat belt that is anchored on the vehicle seat more than 2 inches forward of the crease between the seat bottom and the seat back. This type of vehicle seat belt anchors the car seat too far forward and the car seat will not be safely...

  • Page 73

    74 9.0 vehicle seat belts if you have one of the vehicle seat belts systems as shown on the previous page, do not use it to secure the car seat in the vehicle. Look in the vehicle for a location that has a more suitable vehicle seat belt system as described in the “vehicle seat belt systems that are...

  • Page 74

    To remove back support: • place car seat base on the floor or other firm surface and loosen the harness to align back support tabs to seat base openings . (see “adjustment of the harness straps” section 10.2). • push back support firmly downward with back support tabs fully inserted into the seat base ...

  • Page 75

    76 the harness system on this car seat has an adjuster allowing 1. Tighten the harness straps to snugly adjust harness around child by pulling the harness adjuster strap at the front of the car seat as shown. 2. Make sure the straps are flat and snug against the child’s shoulders and thighs. Note: a ...

  • Page 76

    77 3. Check that the harness straps are snugly adjusted. The harness strap is properly tightened if you are not able to insert more than one finger between the harness strap and the child’s shoulder or thigh. To loosen harness or lengthen the harness strap: 1. Unbuckle harness. 2. Loosen built-in saf...

  • Page 77

    78 10.3 changing harness strap height warning! Death or serious injury can occur: • harness straps must be at or above the ch ild’s shoulders. Failure to properly ad just the harness on your child increases th e risk of death or serious injury in the ev ent of a sudden stop or crash. • discontinue u...

  • Page 78

    79 the harness can be adjusted to three different heights. The proper height of the harness straps is at or just above your child’s shoulders. If your child’s shoulders are between two levels, always use the higher of the two. Remove the body insert if your child’s shoulders are above the highest set...

  • Page 79

    80 harness straps into the matching harness straps slots in the back re-attach the harness straps at the required height by placing the support pad and back support, a. - thread shoulder strap covers over harness straps. - thread velcro straps on shoulder strap covers through same harness slot as th...

  • Page 80

    81 10.4 harness removal and assembly harness removal: hold harness system together. B. Loosen harness straps by depressing the b. Buckle harness and chest clip to harness adjuster and pull out on the harness straps . C. From the back of the car seat, locate the harness connector plate and remove bot...

  • Page 81

    82 e. Remove lower end of harness strap and crotch belt. - from bottom of seat base, pull the m eta l harness retainer away from the bo tto m of the seat base. - rotate the metal harness retainer and ha rn ess strap to position the narrow sid e of the metal harness retainer int o the harness slot. -...

  • Page 82

    83 harness assembly: warning! • harness straps must be at or above the ch ild’s shoulders. Failure to properly ad just the harness on your child increases th e risk of death or serious injury in the ev ent of a sudden stop or crash. A. Place harness assembly in seat with buckle facing down into seat...

  • Page 83

    84 - slide the metal harness retainer through th e h arness slot opening in the seat pad an d seat base. - pull the metal harness retainer down th rou gh the harness slot on the shoulder aw ay from the bottom of the seat base, position the metal harness retainer flat ag ai nst the car seat and pull o...

  • Page 84

    85 10.0 operation and adjustments - from back of car seat, pull harness straps through the harness strap slots in back support until you have enough strap to reach the belt adjuster plate . - inspect the harness straps from the front and back of the car seat to ensure that they are not twisted. Twis...

  • Page 85

    86 10.5 adjusting the head support the head support on this car seat is designed to provide maximum lateral head protection. Never remove the head support from the back support. The head support can be moved up or down through a series of positions. To adjust head support: hold firmly on the top of t...

  • Page 86

    87 10.6 assembly and removal of vehicle shoulder belt positioner use the shoulder belt guide to center the vehicle shoulder belt on the child’s shoulder. Shoulder belt must be centered on child’s shoulder as shown. To attach vehicle shoulder belt positioner: - lay vehicle shoulder belt positioner ou...

  • Page 87

    88 use and adjustment of vehicle shoulder belt positioner - insert the vehicle shoulder belt into both sides of the shoulder belt guide. - pull the free end of the strap down to tighten the shoulder belt guide against the child’s shoulder and bring the shoulder belt into the proper position. To remo...

  • Page 88

    89 11.1 certifications this car seat conforms to all federal motor vehicle safety standards for use in motor vehicles and aircraft. See use modes below: to ddler car seat mode ( harness system): with this restraint is certified for use in motor vehicles and aircraft. Bo oster car seat mode ( harness s...

  • Page 89

    12.0 90 cleaning and maintenance the hard surfaces of the car seat (plastic components and metal parts) except the buckle, may be cleaned by wiping with a solution of water with mild soap. Do not use bleach as it may weaken plastic component. Dry all surfaces with a clean towel. Do not use lubricant...

  • Page 90

    91 to remove head support pad: to remove back support pad: • pull pad off head support. • slide elastic material near shoulder belt slot. Section). • remove harness (see “harness removal and assembly” • r emove back support from seat base (see “assembly and removal of back support” section). • undo v...

  • Page 91

    92 to temove seat base pad: • s urface wash only with mild soap and water. Rinse with • remove harness and crotch strap (see “harness removal and assembly” section ). • remove cup holder by lift straight up • s lide elastic material near corners and pull pad away. • slide the base seat pad armrest c...

  • Page 92

    13.0 93 replacement parts if you need help or replacement parts, please call our customer service department at 01-719-212-6016 between the hours of 8:00 am and 4:30 pm, pacific standa r d time, monday through friday or visit us online at www.Sentrybabyproducts.Com. 13.0 replacement parts.

  • Page 93

    94 14.0 how to register your car seat please complete the following information. The model number and manufactured in (date) can be found on a label on the bottom of the child restraint. Model number : _________________ manufactured in (date) : _________________ purchase date : _________________ ple...

  • Page 94

    Tm sentry baby products, llc 6660 delmonico drive, suite d470 colorado springs, co 80919 sbp16019.