Sevenoak SK-EBH01 Manual - page 2
Specifications:
SK-EBH01 is a specially designed light weight and portable
electronic panorama ball head for use with smart phone, Gopro
cameras, and light weight camera around 1.5KG. SK-EBH01 is
an easy-to-use time lapse device, users can set different rotating
angle and time directly on the device. SK-EBH01 comes with 1/4”
screw thread on the top for mounting camera and comes with
1/4” screw hole at the bottom, so it can be used together with
tripod, slider or any other device with 1/4” screw thread. With
SK-EBH01, users can make their own time lapse videos easily
with low budget.
①. Battery charger jack
②. Battery charger indicator
Thanks for choosing Sevenoak and congratulations on your
purchase of Sevenoak SK-EBH01 Electronic ball head. Before
use, please read the instruction manual and follow the instructions.
Duration Start/Stop R .T
5'
15' 30' 60'
15
°
30
°
45° 60
°
90
°
180°360
°
DIR
DIR
①
②
①
①
①
①
②
⑥
⑤
⑦
③
④
DC 12V
Charger
①. Power switch on/off
Off
On
Power
①. 1/4”-20 screw thread on the top
①. 1/4”-20 screw hole at the bottom
Battery capacity: 1200Mah
Charging voltage: DC 12V
Working temperature: -10~45 degree
Standby time: over 50 hours
Max load capacity: 1.5KG (Horizontal)
Max load capacity: 1.0 KG (30 degree slope)
Max load capacity: 0.8KG (Vertical)
Max load capacity: 1.5KG (Hang upside down)
Battery charge time: 4 hours
Motor: step motor
Battery life: 6 hours when the load capacity is about 1KG
Components:
1. Angle/duration indicator
2. Rotating time indicator
3. Direction indicator
4. Angle/duration selecting button
5. Rotating time selecting button
6. Start/stop button
7. Clockwise/anti-clockwise buttons
Start to set:
1. Turn the power switch on, when the R.T LED “5’ “and Duration
LED “15°” are on means this device is working normally.
2. Duration button means that you can select different angle at
your desire. Press Duration button, select an angle (such as 90°)
you need, the LED under the angle (such as 90°) will be on. This
means that the angle has been set correctly.
3. R.T button means that you can select a time to accomplish
the angle you selected. Press R.T button, select a time (such as
5’) you need, the LED under the time (such as 5’) will be on.
This means that the time has been set correctly.
4. Start/stop button means to start or stop the setting you
selected. Press Start/stop button, SK-EBH01 starts to work as
the setting you selected, press Start/stop button again, SK-EBH01
stops working, and in the meantime, the setting you selected
will not be saved automatically.
5. When SK-EBH01 stops working (but with power on), you can
set it to run clockwise or anti-clockwise by short pressing
Duration and R.T button at the same time.
6. After use, switch the power off, the Duration and R.T LEDs
will be off which means the device is off.
Note:
When four R.T LED lights blink at the same time, it
means battery is low or will be power off soon, you need a
12V DC adapter to re-charge the battery.
Do not force to rotate the rotating table by hand to avoid
damage the motor inside.You can set the device to run 360
degree in 5 minutes, when it comes to 0 degree, press the stop
buttom.