Smart Temp 44-233 Owner's Manual
Smart Temp
Model 44-233
Electronic Manual Thermostat
Owners Manual
Congratulations on the purchase of your new Electronic
Thermostat!
Your new Smart Temp thermostat
and design philosophy. As a result, if properly installed your new electronic
programmable thermostat will provide you with years of trouble free and
reliable service.
The Smart Temp 44-233 has been designed to be attractive, highly reliable
and simple to use. Please take the time to read these simple instruction to
familiarise yourself with the function and features offered in this product.
has been built using the best components
F
HEAT COOL SPAN
SET
TEMP
FILTER
F
C
Your Smart Temp model 44-233 is a non programable thermostat
capable of controlling both Heating & Cooling systems. As this
thermostat is non programable it does not require a complicated set up
procedure. Simply select your required mode of operation and set your
desired temperature. The 44-233 will then control your Heating or
Cooling system to maintain your set temperature.
Please note: Even though this thermostat is capable of controlling both
a heating and a cooling system, you may not have a heating or cooling
system installed in your home.
Selecting Mode
Your thermostat has 3 modes of operation as selected
by the “Mode” switch. These functions are described
below. The mode switch is found under the lower flap -
see Fig 2 below.
Off
In this position your thermostat will not control your heating or cooling
system regardless of your set temperature and the room temperature.
Heat
When “HEAT” is selected your thermostat will turn on your home
heating system if your room temperature falls below your heating set
temperature. When your thermostat calls your heating system to
operate and supply warm air into your home, the word “HEAT” will be
shown in the LCD to confirm heating is required. If the word “HEAT”
flashes in the LCD there is a 4 minute system time delay in progress.
There is NO control of your cooling system in this mode.
Cool
When “Cool” is selected your thermostat will turn on your home cooling
system if your room temperature raises above your cooling set
temperature. When your thermostat calls your cooling system to
operate and supply cooled air into your home, the word “COOL” will be
shown in the LCD to confirm cooling is required. If the word “COOL”
flashes in the LCD there is a 4 minute system time delay in progress.
There is NO control of your heating system in this mode.
Selecting Fan Operation
Your thermostat can control your heating or cooling
system fan in two ways as described below. The fan
switch is found under the lower flap - see Fig 2 right.
Auto
In this position the fan will turn on and off when the heating or cooling
turns on and off. This is the recommended position for this switch.
On
In this position the Heating and Cooling systems fan will operate
continuously, 24 hours a day 7 days a week. This mode is ideal when
you wish to improve the ventilation in your home without changing
the temperature.
System
Cool Off Heat
Fan
On Auto
Fig 2
Setting your desired Temperature
To adjust your desired temperature first select the operational mode,
either heating or cooling.
Next, press and hold either the up button or the down button. The
LCD will show the words “SET TEMP” and either “HEAT” or “COOL”.
The set temperature will then start to move in the required direction.
When your desired temperature is shown in the LCD take you finger
from the button and the LCD will return to the normal display. Your
new set temperature is active.
If heating or cooling is desired the word HEAT or COOL will be shown
in the LCD to confirm this function is required.
LCD Back light
The LCD will illuminate when ever a button is pressed to assist with
the adjustment in poorly lit areas. The back light will stay on for 7
seconds after the last button has been pressed.
Low Battery Warning
Your thermostat operates on two ALKALINE “AA”
batteries. When these batteries are low the back
light function is suspended and the low battery
symbol flashes. Replace the batteries as soon as
possible when this symbol is noted. If no action is taken within a few
days the thermostat will shut down until the batteries are replaced.
Filter Warning
The 44-233 records your heating and cooling usage. When the total
accumulated run time reached 400 hours the filter warning symbol
flashes to remind you to clean your return air filter if installed.
Press ands hold the filter button for 5 seconds to reset this counter.
Error Messages
If your thermostat displays E1, E2, Hi or Lo replace your batteries with
2 new “AA” Alkaline batteries even if you have just replaced them. If
the problem persists please call your installer or Smart Temp
Australia P/L
TEMP
22
C
Room/Set Temp
Backlit LCD
Low Battery Warning
Battery compartment door
Function switch
door
Change Filter
Warning
Filter Counter
Reset
Temperature
Adjust
Battery compartment
2 x “AA” Alkaline only
System Mode
Selector
Fan Mode
Selector