Smart View KVM-L?? User Manual - page 2
Installation
PS/2
PS/2
3 in 1
custom
cable
HD-15
VGA
cable
Rear View
Front View
DC 9V
600mA
Adaptor
Local
Monitor
Local
PS/2
Mouse
Local
PS/2
Keyboard
PC
PS/2
PS/2
HD-15
VGA
cable
KVM-R (Remote)
Rear View
Front View
DC 9V
600mA
Adaptor
Remote
Monitor
Remote
PS/2
Mouse
RemotePS/2
Keyboard
KVM-L (Local)
1. Connect PC console port by using standard 3-in-1
cable to Local. (First connects PS/2 mouse, then
connects PS/2 keyboard and VGA connector).
2. Connect CAT5 cable to Local.
3. Connect CAT5 cable to Remote.
4. Connect keyboard, mouse and monitor to Local.
5. Connect keyboard, mouse and monitor to Remote.
6. Power on PC and Local.
7. Check the VGA quality by the monitor. If the video
quality is not good. Please use hot key of Remote to
adjust the video quality.
Operation
Change hot key in Local and Remote
Press hot key (default: Scroll Lock) twice to enter the
command mode, and press below key to select, and
press “ESC” key to exit command mode.
Key
Function
Scroll lock
“Scroll lock” is the hot key.
Num lock
“Num lock” is the hot key.
Shift (left/ right)
“Ctrl” (left/ right) is the hot key.
-4-
Mode switch of KVM-E
ΙΙ
KVM-E
ΙΙ supports three modes:
Share mode:
The two users (Local and Remote) can access one
PC base on a first-come, first-served policy.
When the Local user accessing the PC, the Link
LED of Remote will flash to remind the other user
that it can’t access now, and vice versa.
Local only mode:
Only the Local user can access the PC. The
Remote user can’t access the PC (include the
video).
The Power LEDof Local and Remote will flash to
remind both the Remote and the Local user that
right now only the Local can access the PC.
Only the Local user can switch the access mode.
KB/MS disable mode:
The Remote user can’t access the PC by keyboard
and mouse, but can see the video. The Local user
can access the PC and see the video.
The Local user can switch the mode by two ways:
Toggle the push button in the front panel of Local.
Press hot key (default: Scroll Lock) twice to enter
the command mode, and press below key. After
operation, press “ESC” key to exit command mode.
Key
Function
L
Switch to “Local only” mode.
S
Switch to “Share” mode.
K
Switch to “KB/MS disable” mode.
-5-
Configure Video quality by Remote User
Our KVM Extender provides 2 ways to adjust video
quality: Manually or Automatically. The user can
process the adjustment by hot key as follow.
Press hot key (default: Scroll Lock) twice of Remote to
enter the command mode, and press below key to select
video adjustment function. Then press ↑ or ↓ key to adjust
the value. When finished, press “ESC” key to end adjust.
Key
Function
A
Adjust video quality Automatically.
N
Adjust video Gain.
E
Adjust video Equalization.
D
Set video and hot key to Default.
NOTE: Allthe video parameters have 32 levels to adjust.
You can also press & hold ↑ or ↓ to continually adjust
video, and if you adjust it to the last level then there will
be a “long” beep sound.
Troubleshooting
1. If the Power LED of Remote is not on, please make
sure power adapter is connected to Remote.
2. If no video signal is displayed on the monitor.
(1) Please check all of VGA cable and CAT5 cable
is loosened or disconnected.
(2) 3-in-1 cable was not attached to PC during boot
up process.
(3) Power adapter is not connected.
3. If video signal is foggy or un-clear, please check VGA
connector, or low the VGA resolution for long cable. It
is highly recommended to use “optimal CAT5 cable
length” to get the best video quality and not to waste
unnecessary CAT5 cable.
4. For the PC without PS/2 connector, please apply
PS/2-to-USB adapter to Local.
© C&C TECHNIC TAIWAN CO., LTD. All rights reserved.
Trademarks:
All the companies, brand names, and product names
referred to this manual are the trademarks or registered
trademarks belonging to their respective companies.
-6-